Where is the cabin air filter located in the Ford Mondeo?

2 Answers
GenevieveLee
07/28/25 6:37pm
The cabin air filter in the Ford Mondeo is located inside the glove compartment on the passenger side. The method to replace the cabin air filter is as follows: 1. Remove the air vent above the passenger-side glove compartment; 2. Remove the decorative cover panel on the right side of the glove compartment; 3. Use a screwdriver to remove the screws on the glove compartment; 4. Disconnect the lighting wire inside the glove compartment; 5. After removing the glove compartment, the cabin air filter will be visible. After replacing the cabin air filter, reassemble the glove compartment in the reverse order of disassembly. The Ford Mondeo is a mid-size sedan produced by Ford Motor Company, with body dimensions of 4873mm in length, 1852mm in width, and 1470mm in height, a wheelbase of 2850mm, and a top speed of 218km/h.
Was this review help?
16
4
Share
StElizabeth
08/12/25 12:10am
I remember the cabin air filter of my Ford Mondeo is located behind the glove compartment on the passenger side, which is super easy to access. I've replaced it myself several times. First, empty all items from the glove box, then locate the clips at the bottom and gently press to release them. After removing the glove box, you'll see the filter cover. Unscrew or unclip it to pull out the old filter. When installing the new filter, pay attention to the arrow direction, which usually points toward the rear of the vehicle. The whole process is straightforward and can be done without tools, taking about 10 to 20 minutes. The filter costs just tens of yuan online and can effectively filter dust and pollen, improving cabin air quality. It's recommended to replace it annually or every 15,000 kilometers to prevent odors and weak airflow from the AC.
Was this review help?
4
0
Share
Expand All
More Forum Discussions

Where is the OBD of Dongfeng Peugeot 308 located?

The OBD of the older model Dongfeng Peugeot 308 is located in a small compartment under the ashtray in front of the front gear lever, and it can be seen by removing the black plastic plate below; the OBD of the new model is inside the decorative panel below the steering wheel on the left side, and it can be seen by pulling the panel outward with force. OBD is the on-board diagnostic system, which monitors the operating condition of the engine and the working state of the exhaust after-treatment system at all times. Dongfeng Peugeot 308 is a compact car with a length, width, and height of 4590mm, 1820mm, and 1488mm respectively, and a wheelbase of 2675mm. The car is also equipped with LDWS lane departure warning system, dual xenon headlights, and up to 9 airbags, including 2 side airbags and a steering column airbag.
12
4
Share

What does PEPS mean on a car?

PEPS on a car refers to the Passive Entry Passive Start system, which is a keyless system that allows for intelligent entry and starting. When the driver enters a specified range, the system can identify the authorized driver and automatically unlock the doors. When leaving the vehicle, the doors will automatically lock and enter an anti-theft state. Additionally, the system can remember all service and diagnostic information, such as seat adjustments, air conditioning settings, and entertainment preferences. The working principle of the keyless system is as follows: 1. The driver approaches the vehicle with the key fob. When pressing the vehicle button or pulling the door handle, the vehicle receives a signal to start or unlock and sends a signal to the low-frequency antenna. 2. Upon receiving the signal, the low-frequency antenna sends a low-frequency trigger signal to the key fob. 3. The key fob receives the low-frequency trigger signal and emits a high-frequency unlock signal. 4. The high-frequency receiver receives the unlock signal, and the entire vehicle completes the unlocking or starting process.
11
1
Share

How to Use the Cruise Control in the New Passat?

The usage of the cruise control in the new Passat is as follows: 1. Maintain the car within a certain speed range, flip the small toggle knob above the car's turn signal controller to the ON position; 2. If you need to increase the speed, press the RES plus button above until the speed reaches the desired value; 3. If you need to decrease the speed, press the SET minus button below until the speed reduces to the desired value. The new Passat is a mid-size sedan designed by Volkswagen, which applies advanced engineering technology and surpasses the standard design of mid-size sedans in terms of power performance, overall design, safety concept, driving comfort, durability, and reliability.
5
0
Share

How to Turn on the Heater When There's AUTO in the Car?

Press the "AUTO" button, and the automatic air conditioning will adjust automatically based on the temperature inside the car. You should first start the engine to warm it up, wait until the engine temperature gauge needle reaches the middle position. Turn on the heater air conditioning, and set the air circulation to external circulation to allow the cold air inside the car to be expelled. After waiting for 2 to 3 minutes, set the air circulation to internal circulation. Choose an appropriate air conditioning temperature. Setting the temperature too low in summer can affect health, so the air conditioning temperature adjustment must be appropriate.
15
0
Share

How to Handle Insurance Transfer for Vehicle Ownership Change?

The original owner should fill out an application form for vehicle insurance transfer; The original owner or an authorized agent should bring the vehicle insurance documents and the vehicle registration certificate to the relevant insurance company to obtain an endorsement for changing the insured party; The original owner or an authorized agent should fill in the details of the insured party change on the received endorsement and complete the vehicle ownership transfer; The new owner only needs to bring the transfer invoice and a copy of the vehicle registration certificate to the original insurance company to obtain the transfer application documents.
13
4
Share

How to Lift the Wiper Blades on the Lamando?

The method to lift the wiper blades on the Lamando is: 1. Turn off the car, then within 10 seconds, activate the windshield washer switch by pulling the wiper lever toward yourself; 2. After pressing the windshield washer switch, the wiper blades will automatically move to the middle position of the windshield; 3. Simply lift the wiper blades manually. To reset them, follow the steps in reverse order. The Lamando is a compact car produced by SAIC Volkswagen, with dimensions of 4599mm in length, 1826mm in width, and 1425mm in height, and a wheelbase of 2656mm. The front of the car features a family-style design, with a three-bar grille connected to the headlights and round fog lights positioned on either side of the bumper.
20
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.