Where is the cabin air filter located in the C4L?

1 Answers
McJoanna
07/30/25 9:37am
The cabin air filter in the C4L is located in the engine compartment. Open the engine hood, and you will find it beneath the windshield wiper drainage channel. There are four round plastic fasteners from left to right. After removing these fasteners and opening the cover, you can access the cabin air filter. The cabin air filter is a component installed in the car's air conditioning system, designed to absorb dust particles, alleviate respiratory discomfort, reduce irritation for allergy sufferers, and protect the air conditioning cooling system. The Citroën C4L is a model launched by Dongfeng Motor Corporation, with dimensions of 4675mm in length, 1780mm in width, and 1500mm in height, and a wheelbase of 2710mm. In terms of exterior design, the vehicle features a horizontal grille design on both the upper and lower sections. The headlights are connected to the front grille, while the fog lights are integrated with the lower grille. The daytime running lights are incorporated into the overall lighting assembly, embodying a harmonious blend of strength and beauty.
Was this review help?
14
2
Share
More Forum Discussions

What are the symptoms of a faulty BMW eccentric shaft sensor?

BMW eccentric shaft sensor failure can cause the car to fail to start. The criteria for judging bearing damage mainly depend on two manifestations: vibration and temperature. Vibration of eccentric bearings: Bearing vibration is highly sensitive to bearing damage, such as spalling, indentations, rust, cracks, and wear, all of which can be reflected in bearing vibration measurements. Therefore, by using special bearing vibration measuring devices (such as frequency analyzers), the magnitude of vibration can be measured, and the specific abnormality can be inferred from the frequency distribution. The measured values vary depending on the bearing's operating conditions or the sensor installation position, so it is necessary to analyze and compare the measurement values of each machine in advance to determine the judgment criteria. Temperature of eccentric bearings: The temperature of eccentric bearings can generally be inferred from the temperature outside the bearing housing. If the outer ring temperature can be directly measured using an oil hole, it is even more suitable. Typically, the temperature of eccentric bearings gradually rises as the bearing begins to operate and stabilizes after 1-2 hours. The normal temperature of the bearing varies depending on the machine's heat capacity, heat dissipation, speed, and load. If lubrication or installation is improper, the bearing temperature will rise sharply, leading to abnormally high temperatures. In such cases, operation must be stopped, and necessary preventive measures must be taken. Using thermal sensors, the working temperature of the bearing can be monitored at all times, and automatic alarms or shutdowns can be implemented when the temperature exceeds the specified value to prevent bearing seizure accidents.
18
1
Share

Does the Besturn B50 have one-touch window lift function?

The Besturn B50 has one-touch window lift function. Spacious appearance, large space, and low fuel consumption are several major advantages of the Besturn B50. Appearance: The Besturn B50 has a grand, stable, and highly modern appearance that has won consumer approval. Space: The space is relatively large, but headroom is insufficient. Low fuel consumption In terms of product positioning, the Besturn B50 leans more towards family users, so the vehicle maintains a relatively low fuel consumption level. During test drives under different road conditions, with the air conditioning set to maximum, the comprehensive fuel consumption of the Besturn B50 is about 7.5, which will satisfy many consumers.
8
3
Share

Where is the oil filter of the X-Trail located?

The oil filter of the Nissan X-Trail is located on the left side of the lower engine when the vehicle is lifted. Using an oil filter is very necessary. If the oil does not pass through it, it will affect the vehicle. Reasons for using an oil filter: To reduce the frictional resistance between the moving parts in the engine and minimize wear on the components, oil is continuously delivered to the friction surfaces of the moving parts, forming a lubricating film for lubrication. The oil itself contains a certain amount of gum, impurities, water, and additives. During engine operation, the introduction of metal particles, contaminants from the air, and the generation of oil oxidation products gradually increase the contaminants in the oil. It is necessary to filter out the contaminants, gum, and water from the oil to deliver clean oil to the lubrication points. Effects of not filtering: If the oil is not filtered and directly enters the lubrication circuit, it will carry the contaminants present in the oil into the friction surfaces of the moving parts, accelerating component wear and reducing the engine's service life.
19
3
Share

How Many Kilometers Should a BMW Undergo a Major Maintenance?

BMW major maintenance is recommended every 30,000 kilometers. Different components of the car have varying maintenance intervals. Spark Plugs: Spark plugs are a key component in the ignition system of a car engine. For BMW models, the recommended maintenance interval is at least every two years or approximately 20,000 kilometers (only for B-series engine models). For previous N-series engine models, it is recommended to perform spark plug maintenance every four oil changes. Wiper Blades: Wiper blades are made of rubber and are used frequently in summer. High temperatures and rain can easily cause them to age, while sub-zero temperatures in winter can harden the rubber. They should be replaced promptly if they fail to clean the windshield effectively. The recommended maintenance interval for BMW models is every two to three years or approximately 20,000~30,000 kilometers. Brake System: Prolonged braking increases wear on the brake pads. If there are abnormal noises or ineffective braking, they should be inspected and replaced promptly. Brake Fluid: The recommended maintenance interval is at least every three years or approximately 30,000 kilometers. The first brake fluid maintenance for a new car is at 36 months, with subsequent intervals at 24 months.
18
1
Share

What is the maintenance interval for Audi?

Maintenance cycle is every 10,000 kilometers or 12 months. Specific routine maintenance items include engine oil and oil filter. Engine oil: There are many types and brands of engine oil to choose from. Audi semi-synthetic, Fuchs, Golden Shield, and Extreme Protection are among the brands used. The theoretical replacement cycle can be as long as 10,000-15,000 kilometers, suitable for temperatures above 30 degrees and ideal for vehicles in northern regions. Oil filter: Although the oil filter only serves to filter impurities from the oil, acting as a simple filter screen, its position is crucial. It directly affects the purity of the oil, ensuring the engine's performance. It must be replaced along with the engine oil during every maintenance. The model of the oil filter varies depending on the engine displacement.
13
1
Share

What is the origin of GAC Trumpchi?

GAC Trumpchi (abbreviated as Trumpchi) is a domestic brand created by GAC Group to enhance core competitiveness and achieve sustainable development. Brand Culture: GAC Trumpchi is the first independently developed model by GAC Group, positioned in the mid-to-high-end market. Adhering to the brand philosophy of "Building good cars for loved ones and filling the world with love," it integrates GAC Group's resources and experience, insists on independent innovation, and is committed to developing models suitable for Chinese driving habits and road characteristics. Corporate Honors: On December 15, 2019, GAC Trumpchi was awarded the Top Ten Annual Emerging Brands at the 2019 China Brand Power Ceremony.
16
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.