Where is the cabin air filter located in the 508?

1 Answers
DawsonLynn
07/30/25 7:13am
The cabin air filter in the 508 is located above the accelerator pedal under the dashboard on the driver's side. The cabin air filter is a filter installed in the car's air conditioning system, which can absorb dust particles, alleviate respiratory discomfort, reduce irritation for allergy sufferers, and protect the air conditioning cooling system. The 508 is a mid-size sedan under Dongfeng Peugeot, equipped with a 1.6T turbocharged engine producing a maximum horsepower of 170 HP. The dimensions of the 508 are 4870mm in length, 1855mm in width, and 1455mm in height, with a wheelbase of 2848mm, and it comes with a 6-speed automatic transmission. The car has a top speed of 220 km/h, a trunk capacity of 513L, and uses a front-engine, front-wheel-drive layout.
Was this review help?
3
0
Share
More Forum Discussions

How to Eliminate the Yellow Engine Light?

Methods to eliminate the yellow engine light: The owner can try starting and turning off the vehicle three times in a row, or disconnect the negative terminal of the engine battery, wait for 30 seconds, reconnect it, and then attempt to start the vehicle. After performing the above steps, check if the engine warning light on the dashboard is still on. It is important to note: When the engine warning light on the dashboard is illuminated, it cannot be manually eliminated. Typically, it is necessary to visit a 4S shop to use a fault detection device for troubleshooting before the light can be turned off. Reasons for the yellow engine light on the dashboard: 1. Sensor issues; 2. Maintenance problems; 3. Fuel quality issues; 4. Poor combustion of the air-fuel mixture; 5. Intake problems.
18
0
Share

Where is the Cruze air intake located?

The air intake of the Cruze engine is located at the junction between the right front bumper and the fender. Below are the specific details about the Chevrolet Cruze: 1. Dimensions: The Cruze measures 4630mm in length, 1798mm in width, and 1485mm in height, with a wheelbase of 2640mm. 2. Lighting configuration: The Cruze comes standard with LED lighting technology across all models. The sharp-looking LED automatic sensing headlights feature Chevrolet's classic dual-element design and are equipped with three-dimensional LED light conductor daytime running lights. 3. Powertrain: The Cruze is equipped with two engines, one being a 1.0-liter turbocharged engine and the other a 1.3-liter turbocharged engine. The 1.0-liter turbocharged three-cylinder engine delivers a maximum power of 92 kW and a maximum torque of 170 Nm, while the 1.3-liter turbocharged engine produces a maximum power of 120 kW and a maximum torque of 230 Nm.
6
4
Share

What Causes the Car's Auxiliary Water Tank to Always Lack Water?

The reasons why the car's auxiliary water tank always lacks water are as follows: 1. Cylinder head gasket: Frequent water shortage indicates a leak in the cooling system or a slight cylinder head gasket failure. 2. Overheating: Excessive coolant temperature can also lead to system water shortage, and leaked coolant can be seen from the front of the engine. 3. Water pump seizure: A seized water pump can cause timing belt damage, leading to piston top valve and other related component issues. 4. Cylinder gasket failure: A failed cylinder gasket (air or water passage) can mix with engine oil or be expelled through the exhaust pipe, causing water shortage. 5. Water-cooled air compressor: Leakage due to air compressor steel gasket failure.
20
3
Share

What is the reason for the gw250f1 light coming on?

gw250f1 light coming on indicates a fault in the fuel injection system. It is necessary to go to the after-sales service to read the fault code based on the flashing of the indicator light to determine the fault. The following are specific introductions about the fuel injection system: 1. Introduction: The electronically controlled gasoline injection system uses the electronic control unit as the control center and utilizes various sensors installed on the engine to measure various operating parameters of the engine. Then, according to the control program pre-stored in the computer, it precisely controls the fuel injection quantity of the injector, so that the engine can obtain the best air-fuel ratio of combustible mixture under various working conditions. 2. Principle: Using various sensors installed on different parts of the engine and the vehicle, the system measures various working parameters of the engine. Through the set control program and data, it precisely controls the fuel injection timing of the fuel injection pump, so that the engine can obtain the best fuel injection timing under various working conditions, meeting the requirements of output torque, low fuel consumption, and emission standards.
19
5
Share

What Causes the Squeaking Noise When the Front Wheels Go Over Bumps?

Front wheels squeaking when going over bumps is usually caused by damaged rubber bushings in the shock absorber system, and replacing them can resolve the issue. Below are specific details about the shock absorber system: 1. Introduction: In the suspension system, vibrations are generated when elastic components are impacted. To improve ride comfort, shock absorbers are installed in parallel with the elastic components in the suspension. Most shock absorbers used in automotive suspension systems are hydraulic shock absorbers designed to dampen vibrations. 2. Principle: The working principle involves the piston inside the shock absorber moving up and down when relative motion occurs between the frame (or body) and the axle due to vibrations. The oil in the shock absorber chamber repeatedly flows from one chamber to another through various orifices.
9
0
Share

Should I buy the 2019 or 2021 Lavida?

This depends on the owner's personal needs. The differences between the 2019 Lavida and the 2021 Lavida are: 1. Different body dimensions: The 2019 Lavida has a body length, width, and height of 4613mm, 1765mm, and 1460mm respectively; the 2021 Lavida has a body length, width, and height of 4670mm, 1806mm, and 1474mm respectively. 2. Different wheelbase: The 2019 Lavida has a wheelbase of 2610mm; the 2021 Lavida has a wheelbase of 2688mm. 3. Different engines: The 2019 Lavida is equipped with an EA211dlf engine; the 2021 Lavida is equipped with an EA211dmb engine. 4. Different lighting configurations: The 2019 Lavida uses halogen light sources for its high and low beam headlights; the 2021 Lavida uses LED light sources for its high and low beam headlights.
14
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.