Where is the cabin air filter located in a Ford Mondeo?

2 Answers
SanAsher
07/28/25 7:39pm
Mondeo's cabin air filter is located on the right side of the driver's accelerator pedal, which requires removing the accelerator pedal to access it. The cabin air filter functions to purify incoming outside air before it enters the vehicle interior. The replacement procedure is as follows: 1. First remove the air vent above the glove compartment on the passenger side, which is secured by three plastic clips - apply moderate force during removal to avoid damage. 2. There's a decorative panel on the right side of the glove compartment, remove it using the same method. 3. Use a screwdriver to remove six screws on the glove compartment. 4. After removing all screws, disconnect the glove compartment lighting wire and pull the glove compartment outward. 5. The cabin air filter becomes visible after removing the glove compartment. After replacement, reassemble the glove compartment by reversing the removal sequence.
Was this review help?
9
0
Share
Felix
08/12/25 12:33am
I must say, the cabin air filter in a Ford Mondeo is usually located right behind the glove box. You can spot it as soon as you open it, but you'll need to remove a few screws or clips first to access it. When I drive this car myself, I prefer changing the filter by hand to avoid unnecessary expenses at the shop. Last summer, after installing a new filter, the air inside the car immediately felt fresher—no more dust blowing around and irritating my nose like before. I recommend checking it regularly, say every 10,000 kilometers or once a year. Otherwise, accumulated dust can easily trigger allergies or cause unpleasant odors from the AC. When replacing it, opt for an aftermarket brand filter—online options cost just over ten bucks, simple and cost-effective. Make it a habit to keep the glove box clutter-free for easy maintenance, which helps prolong your car's lifespan.
Was this review help?
16
5
Share
Expand All
More Forum Discussions

Can a new car run on the highway?

A new car can run on the highway. The precautions for high-speed driving are: 1. When entering the main lane from the ramp onto the highway, quickly increase the speed to a certain level; 2. When merging, do not obstruct vehicles already driving in the main lane; 3. Always pay attention to roadside and road signs and markings while driving, and keep appropriately to the right; 4. Maintain a safe longitudinal distance between vehicles; 5. When overtaking, turn on the left turn signal and honk the horn, passing the vehicle ahead from the overtaking lane; 6. In case of an emergency requiring a stop, quickly signal to the right, stop slowly in the emergency parking area, turn on the hazard lights after stopping, and set up a warning sign behind the vehicle; 7. Distinguish lane functions and drive in the appropriate lane.
14
4
Share

Where is Lynk & Co manufactured?

Lynk & Co is manufactured by Geely Auto. The models under the Lynk & Co brand include: Lynk & Co 03, Lynk & Co 01, Lynk & Co 02, Lynk & Co 01 New Energy, Lynk & Co 05, etc. Taking the 2021 Lynk & Co 03 as an example, it belongs to the compact car category with body dimensions of: length 4639mm, width 1840mm, height 1472mm, and a wheelbase of 2730mm. The curb weight is 1395kg. The 2021 Lynk & Co 03 features a MacPherson strut front suspension and a multi-link independent rear suspension. It is equipped with a 1.5T turbocharged engine, delivering a maximum horsepower of 156PS, a maximum power of 115kW, and a maximum torque of 245Nm, paired with a 6-speed manual transmission.
2
4
Share

What is engine oil composed of?

Engine oil is composed of base oil and additives. Engine oil, also known as engine lubricant, functions to: 1. Reduce friction and high temperatures; 2. Absorb shock and cushion; 3. Prevent rust and corrosion; 4. Cool down the engine; 5. Clean and remove contaminants. The hazards of using inferior quality engine oil include: 1. Reduced power output of the generator set; 2. Damage to the lubrication of precision components such as the fuel pump and injector; 3. Degradation of the oil quality, diminishing its performance; 4. Adverse effects on the engine's combustion efficiency. The method for changing engine oil is: 1. Lift the vehicle with a jack, locate the drain plug, and loosen it to drain the oil; 2. Remove the oil filter and place a container beneath it; 3. Replace with a new oil filter and add fresh engine oil.
11
0
Share

What Causes the Vehicle to Pull to One Side When Braking?

The reasons for the vehicle pulling to one side when braking are: 1. Uneven tire pressure; 2. Different tire tread patterns or varying tread depths; 3. Deformation of the front shock absorber springs; 4. Failure of the front shock absorbers; 5. Body deformation; 6. Excessive wear of chassis components; 7. Incorrect wheel alignment; 8. Brake system malfunction. Directional pull refers to the phenomenon where the vehicle, while driving straight on a flat road, automatically veers to one side, causing the centerline connecting the front and rear axles to deviate from the centerline of the driving trajectory. Methods to adjust directional pull include: 1. Slightly adjusting the steering wheel to the right if the vehicle pulls to the left, and to the left if it pulls to the right; 2. Rotating or replacing the tires; 3. Replacing the suspension springs.
7
2
Share

What does TRC mean on a car?

TRC on a car stands for Traction Control System, and TRC OFF means the Traction Control System is turned off. When the TRC light is on, it is likely that the TRC button was accidentally turned off. If it wasn't turned off, it indicates that there is an issue with the Traction Control System preventing it from functioning properly. The role of the Traction Control System is to ensure the car obtains optimal traction under various driving conditions. The control device is a computer that monitors the speed of all four wheels and the steering wheel's turning angle. When the car accelerates, if the computer detects a significant speed difference between the driving wheels and non-driving wheels, it immediately determines that the driving force is too high and sends a signal to reduce the engine's fuel supply, thereby lowering the driving force and reducing the slip rate of the driving wheels.
4
5
Share

How to Open the Hood of a Toyota Levin?

Toyota Levin's hood opening method is: 1. Open the car door and enter the driver's seat; 2. Locate the hood release lever under the left side of the dashboard; 3. Pull the hood release lever upwards to open the hood. Taking the 2021 Toyota Levin as an example, its body dimensions are: length 4640mm, width 1780mm, height 1455mm, rear track width 1526mm, fuel tank capacity 50 liters, and trunk capacity 471 liters. The 2021 Toyota Levin features a MacPherson strut front suspension and an E-type multi-link rear suspension, equipped with a 1.2L turbocharged engine delivering a maximum horsepower of 116PS and a maximum power output of 85kW.
15
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.