Where is the body control module of Landwind X7 located?

1 Answers
ZacharyDella
07/30/25 7:46am
Landwind X7 body control module is located above the accelerator pedal in front of the driver's seat, specifically on the left side under the dashboard. The main functions of the body control module are as follows: 1. Power management: The BCM integrates the power supply of vehicle electrical equipment, saving wiring harnesses and facilitating later maintenance. 2. Light control: When the BCM detects a short circuit to ground or excessive current in the small light circuit, it activates a protection function to prevent the vehicle's wiring harness from burning due to excessive current. 3. Wiper control: The wiper circuit is relatively complex. Using conventional control would require a large number of wiring harnesses. With the BCM, wiring harnesses are significantly saved, and additional wiper functions are added, such as manually adjusting the speed of the intermittent wiper mode. 4. Central locking and remote control reception: When the BCM detects the vehicle speed increasing from less than 10 km/h to 10 km/h and the door locks are in the unlocked state, it performs a locking operation. If the door locks are already locked, no action is taken. Additionally, after receiving a wireless signal from the remote control, the BCM can control the door locks for operations such as locking, unlocking, opening the tailgate, and vehicle locating. 5. Vehicle anti-theft and engine immobilizer control: When the vehicle's anti-theft system is successfully activated and the vehicle is illegally accessed, the horn will sound and the alarm lights will flash to alert the owner. With the engine immobilizer activated, even if someone duplicates the car key, they cannot start the vehicle. 6. Fault mode self-diagnosis control: When the BCM detects an internal fault, it activates a self-diagnosis function, displaying a fault indicator on the dashboard to remind the owner for maintenance. Additionally, specialized equipment can be used to read data from the BCM to assist in repairs.
Was this review help?
18
5
Share
More Forum Discussions

Is It Dangerous When the Light Is Off but Still Glows Slightly?

It is quite common for the light to still glow slightly when turned off. The reasons are as follows: 1. Capacitor step-down current limiting method: The driver of this LED light uses a very simple capacitor step-down current limiting method, rather than a dedicated and standard isolated switching constant current source; 2. Induced electricity: Although the switch is installed on the live wire, the neutral wire is only at 0 potential relative to the live wire and actually may still have a certain voltage, or induced electricity generated by other circuits. Combined with the high luminous efficiency of small-power LED lights; 3. Discharge causing flickering: After the power is turned off, the fluorescence or accumulated induced electricity discharges to a certain extent, resulting in flickering, which is understandable.
3
4
Share

What Causes Abnormal Noise During Transmission Acceleration?

Transmission acceleration has abnormal noise reasons: Bearing wear and damage: When bearings wear, their clearance increases and fitting accuracy decreases. When bearings are damaged, they cannot operate normally, which will produce abnormal noise and may even damage transmission components, leading to further malfunctions. Transmission component wear: Wear of transmission components or use of replacement parts with excessively low precision, such as gear wear or excessive clearance between new replacement gears and original gears. Insufficient lubrication: Insufficient lubrication oil or excessively high viscosity causing poor lubrication. In this case, the corresponding lubricating oil (grease) should be replaced, otherwise it will accelerate transmission wear and shorten service life.
15
2
Share

What is the safest way to drive when two vehicles meet in foggy conditions?

When driving in foggy conditions and encountering an oncoming vehicle, you should slow down and proceed with caution. Here are some precautions for driving in fog: 1. Pay attention to the relationship between speed and visibility: In heavy fog with low visibility, reduce your speed and adjust it according to the fog density and visibility to ensure you have enough time to react in case of emergencies. 2. Maintain a safe distance from the vehicle ahead: Turn on your vehicle's headlights, taillights, and fog lights. In severe conditions, you may also use hazard lights. Avoid using high beams, as their elevated light beams can easily obscure fog lights and impair other drivers' vision. 3. Use your horn to indicate your position: Honking is particularly effective in foggy conditions, especially for American and European vehicles, as their horns have strong penetrating power in the air and can be heard over long distances.
8
1
Share

What Causes the Abnormal Noise from Car Doors When Starting the Power?

The reasons for abnormal noise from car doors when starting the power are as follows: Noise caused by door seals: After prolonged use, the door seals gradually age, causing friction between the seals and the car body. This can result in abnormal noise while driving. Solution: Replace the door seals. Noise caused by door hinges: Extended use of hinges can significantly increase friction, leading to abnormal noise. Solution: Apply lubricant to the hinges. Noise caused by door limiters: If door limiters are not regularly maintained, they can also cause abnormal noise. Solution: Perform regular maintenance on the door limiters.
3
5
Share

What car has 'RS' on the steering wheel?

Steering wheels with 'RS' belong to Audi's RS series. Meaning of Audi RS: 'RS' stands for RACING SPORT (Racing Sport type). The Audi 'RS' series is entirely designed, developed, and manufactured by Audi's quattro department, and is not produced on the same assembly line as regular Audi models. The entire 'RS' series is equipped with high-performance engines exclusively developed by quattro, delivering extraordinary performance, making them the true flagship models. Models under Audi RS: These include RS3, RS4, RS5, RS6, and RS7.
12
1
Share

What does it mean when a sedan's yellow warning light comes on?

A sedan's yellow warning light comes on due to an engine malfunction. Sensor issues: Sensors include those for coolant temperature, crankshaft position, air flow, intake air temperature, and oxygen sensors. When these sensors are damaged, have poor connections, or experience signal interruptions, the vehicle's ECU cannot accurately obtain engine data, which triggers the engine warning light. Poor fuel mixture combustion: Engine issues such as faulty spark plugs, defective ignition coils, malfunctioning fuel pumps, or clogged fuel lines can lead to poor combustion of the air-fuel mixture. Poor combustion results in engine carbon buildup or knocking, which is detected by the engine's oxygen sensors and reported to the ECU, prompting the warning light to illuminate as an alert.
13
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.