Where is the battery located in a Mercedes S350?

How to Pass Subject Two in One Attempt?

The pass rate for Subject Two is relatively low. On the shuttle bus, you often hear people complaining about things like the car being bad or the test site being non-standard, as if the examiners are deliberately failing students. In reality, it's not that serious at all. The cars may vary slightly, but the impact is minimal; the test sites are all standardized. Those who struggle the most (a significant portion being middle-aged women) are the ones who fail repeatedly and complain the most. Don't listen to them. Paying for a trial test will make things clear. Theoretical Basis One: The Three-Point Alignment Principle When your eyes, a specific point on the car body, and a marker on the ground form a straight line, you can determine the car's position. For example, when reversing into the garage, if your eyes see the lower edge of the left rearview mirror aligning with the garage line, it means the car is perfectly in the garage. Why? Because your eyes, the lower edge of the left rearview mirror, and the ground in front of the car form a straight line. Another example: if your eyes align with a red dot (or a node on the windshield wiper, which could be a dot or a square) and the line on the right side of the road, it means the right side of the car is about 30 cm away from the line. Theoretical Basis Two: The Parallel Principle Two parallel lines remain roughly parallel even under weak perspective. Therefore, if the car body in the rearview mirror appears parallel to the line on the ground, it is actually parallel. Looking to the left, if the left side of the car body is parallel to the line on the ground, it means the car body is parallel to the line. Theoretical Basis Three: Control Methods For humans, many controls are based on feeling, but for machines, control algorithms are needed. In automatic control, the essential steps are: setting a reference target position, observing the actual feedback position, comparing them, and executing the control. Car Principle One: Clutch and Gear Shifting The engine and the wheel drive shaft are connected via the clutch. Simplified, the engine keeps rotating while the other end is a wheel, connected by the clutch. The clutch can be seen as a friction plate. When tightly pressed together, the engine and the wheel are firmly connected; if completely separated, they don't affect each other; if slightly pressed, it's half-clutch. The role of half-clutch: when starting, the engine rotates, but the car remains stationary. If the clutch is fully released and the friction plate is pressed hard, the high-speed rotating engine suddenly collides with the stationary drive shaft, causing the engine to stall. Thus, half-clutch acts as a buffer, allowing gradual contact. This applies not only to starting but also to gear shifting. Controlling speed and clutch essentially means controlling the engine's output power. Car Principle Two: Forward and Reverse Driving The vehicle's steering revolves around a point on the rear axle, creating an arc. From the diagram, you'll notice: the front wheels have a larger turning radius than the rear wheels, so in an S-curve, the rear wheels are closer to the inner line while the front wheels are farther away. The steering direction is the same whether moving forward or backward. Turning the steering wheel to the left will make the car veer left, regardless of direction. Calibration As an engineering student, I know calibration is crucial. Calibration means "establishing standards." Only under consistent standards can you use familiar, unchanging methods for precise control. Calibration mainly involves adjusting the seat and rearview mirrors. My calibration method: first, park the car accurately in the garage, ensuring the lower edge of the left rearview mirror aligns with the garage line and both mirrors show the rear garage corners. This means the seat and mirrors are adjusted to "my standard position." How to Adjust the Seat and Rearview Mirrors Use the above calibration method to find the standard position. However, during the exam, you can't adjust like this, so establish five calibration results for adjustment. Park the car in the garage, adjust the seat and mirrors to the best position, then "one press, two stretches": press the clutch, lean your back against the seat, stretch your left arm forward horizontally to rest on the steering wheel's upper edge, and use your right hand to adjust the seat. If the clutch feels comfortable and your left wrist just rests on the steering wheel edge, it's suitable. Then, lean your back against the seat and stretch both arms forward. If both wrists can rest on the steering wheel edge, it's perfect. Otherwise, fine-tune the seatback angle. "Up, Down, Left, Right": First, adjust vertically so the front door handle is in the middle of the rearview mirror, and the rear door handle is just visible. Then, adjust horizontally so the white car body occupies a quarter of the mirror. Repeat adjustments, ensuring your back is always against the seat. Exam Process 1: Reversing into the Garage Secure the seat, fasten the seatbelt, adjust the seat and mirrors, and release the handbrake. Adjust the car's position if the previous test-taker left it in a poor state.

6

1

Share

What are the causes of ABS ESC failure?

ABS warning light can indicate various conditions, each with different causes and solutions as follows: Condition 1: ABS warning light stays on (most common). Cause 1: The ABS wheel speed sensor's sensing area is covered by mud, dirt, or other contaminants, affecting its ability to detect wheel speed signals. This prevents the ABS control unit from determining vehicle speed or wheel slip rate, thus failing to issue appropriate commands to regulate braking. Solution: Clean contaminants from the wheel speed sensor and adjust the gap between the sensor and tone ring to restore normal function. Cause 2: Loose wiring connections or poor ABS relay contact causing signal interference. Solution: Inspect wiring connections and re-secure any loose parts. Condition 2: ABS warning light intermittently illuminates but turns off during acceleration. Cause: Battery voltage drops below 10.5V when multiple electrical components are in use. The light extinguishes when engine speed increases voltage. Possible low system voltage due to poor terminal contact or grounding issues. Solution: Check battery specific gravity; inspect charging system; examine power supply (e.g., voltage relay or loose power connections). Condition 3: ABS light remains on after engine start until ignition OFF. Cause: Poor ground connection at ABS hydraulic valve body; faulty wiring harness connection; ABS control module malfunction. Solution: Loosen and retighten valve body ground screw (clean contact surface if necessary); check connector gaps; replace ABS or ABS/ASR control module. Condition 4: ABS light activates during high-speed driving. Cause: Significant discrepancy between front/rear wheel speed signals detected by ABS module; incorrect tire or wheel specifications. Solution: Verify correct tire/wheel specifications per vehicle placard (typically on fuel filler door). Condition 5: Intermittent ABS warning light activation. Cause: Improper brake light switch adjustment; internal switch contact failure. Solution: With engine running, fully depress brake pedal while manually pushing switch lever downward, then release pedal to reset position; replace brake light switch if needed. When the ABS warning light is illuminated, continued driving is not recommended as it indicates anti-lock braking system malfunction. During emergency braking, wheel lock-up could cause loss of vehicle control, preventing speed reduction or trajectory adjustment, posing significant safety risks.

16

5

Share

What Causes All Warning Lights to Illuminate and the Car to Fail to Start?

When all warning lights illuminate and the car fails to start, the most common cause is insufficient battery charge. Below are key points regarding the battery: 1. Low Car Battery Voltage: Use a multimeter to test the battery voltage. If it reads below 10V, replacement is recommended. If around 11V, it may still function temporarily, but prepare for replacement. A reading above 12V indicates normal operation. 2. Service Life: Car batteries typically require replacement every 2-4 years. Theoretically, a car battery's lifespan is generally 2-3 years, but with proper use and maintenance, it can last up to 4 years without issues.

4

1

Share

Can a Car Designed for 92 Octane Use 95 Octane Gasoline Long-Term?

92 octane and 95 octane gasoline should not be mixed for long-term use. Relevant explanations are as follows: 1. Long-term mixing may cause knocking, insufficient power, and other issues. Especially for cars designed for 95 octane gasoline, using 92 octane gasoline long-term can increase the frequency of knocking and accelerate engine wear. 2. The octane rating of gasoline represents its anti-knock quality. The higher the octane number, the better the anti-knock performance of the gasoline. Therefore, refueling according to the engine's compression ratio or the requirements specified in the car's manual is more scientific, economical, and can fully utilize the engine's efficiency.

8

3

Share

How to Remove a Paint Protection Film?

Paint protection film removal method: Start from the edge and locate the seal; then peel off the edge, avoiding hard pulling during the process. Instead, use a method of pulling from the inside out. If the film is made of TPU material, the entire film can be removed quickly. After removal, there may be residual adhesive traces at the edges. Spray these with tar remover and wipe them off with a towel. Paint protection film is a high-performance, environmentally friendly film widely used in the automotive film beauty and maintenance industry. It is commonly known as a transparent paint protection film, offering superior toughness. Once applied, it isolates the car's paint from the air, providing long-lasting protection.

9

2

Share

How to Replace the Key Battery for the New Mercedes-Benz C32-AMG?

To replace the key battery for the new Mercedes-Benz C32-AMG, follow these steps: 1. First, locate the sliding switch on the car key and slide it to open the mechanical key. 2. Pull out the mechanical key. 3. After removing the mechanical key, you can see the inside of the car key; insert the metal key and pry open the car key cover. 4. Then, remove the old battery. 5. Insert the new battery and reattach the car key cover. Notes: 1. Do not press the mechanical key downward too hard, as this may break the cover clip. 2. Pay attention to the battery's positive and negative terminals when installing the new battery.

3

Share

Where is the battery located in a Mercedes S350?

How to Pass Subject Two in One Attempt?

What are the causes of ABS ESC failure?

What Causes All Warning Lights to Illuminate and the Car to Fail to Start?

Can a Car Designed for 92 Octane Use 95 Octane Gasoline Long-Term?

How to Remove a Paint Protection Film?

How to Replace the Key Battery for the New Mercedes-Benz C32-AMG?

Why is the car safety indicator light always on?

What engine does the SAIC Maxus V80 use?

Which digit in the VIN represents the year?

What is the tire model for the Atenza 2.0 version?