···
Log in / Register

Where is the AUX interface in the new Focus?

4 Answers
FelixMarie
07/29/25 6:49pm
The AUX interface in the new Focus is located inside the glove compartment in front of the passenger seat. Simply open the glove compartment lid to find it. The AUX is an audio input interface, and its basic working principle is that after connecting to the AUX interface, audio from electronic devices can be transmitted through the headphone jack and AUX interface to the car's audio system, allowing playback through the car's audio broadcasting facilities. The USB interface can be used to insert a USB drive for audio playback. When using the AUX interface, connect one end to the AUX port and the other end to devices like smartphones, MP3 players, or MP4 players. This allows you to listen to songs or niche music anytime, anywhere, without being limited to car music CDs. However, if the playback device runs out of battery, the music will stop (the interface typically uses a standard 3.5mm headphone jack). Aux, short for Auxiliary, refers to an additional signal line design. In general audio equipment, besides the standard output and input terminals, there are often several terminals labeled Aux, serving as backup connection points. These can be used for special applications, such as additional audio output or input. Such backup terminals or lines, whether for input or output, are collectively referred to as Aux. Function: The AUX port is an asynchronous port primarily used for remote configuration, dial-up connections, or connecting to a MODEM via a transceiver. It supports hardware flow control. The AUX port is usually placed alongside the CONSOLE port because they serve different configuration environments. The AUX interface establishes a command-line connection between the user and the device, enabling operations that are typically impossible in user mode, such as initialization, restoring default settings, or correcting abnormal user modes. It provides a fixed port that can function as a standard asynchronous serial port with a maximum speed of 115200 bit/s. Using the AUX interface, remote configuration of hardware products and line backup can be achieved. Note: When using the AUX interface, ensure you purchase the correct connecting cable and avoid plugging the audio cable into the wrong port. It’s best to follow the steps outlined in the product’s user manual. If unsure, consult the product’s official website or contact customer service for guidance.
Was this review help?
5
1
Share
Justin
08/14/25 12:27pm
I've driven quite a few cars, and the AUX port in a Focus is usually hidden inside the glove box. Once you open it, you'll spot the small jack, slightly to the left. If you can't find it, try rummaging through the clutter in the glove box—sometimes the owner's manual is tucked in a corner with a reminder about its location. The new Focus has this discreet design to prevent kids from tampering with it. When plugging in the cable, make sure the connector is clean to avoid poor contact affecting sound quality. Using an AUX cable with your phone provides more stable audio quality than Bluetooth. But if it's not in the glove box, check the storage compartment on the passenger side of the center console—I've seen older models place it there. If you still can't find it, try starting the car and switching to audio mode—if the AUX option appears, it means the port is functioning properly in the system. I recommend buying a high-quality AUX cable to prevent static noise—cheap ones tend to have fragile cores that break easily.
Was this review help?
19
5
Share
Expand All
LeEvangeline
10/14/25 8:25am
I think the AUX port location on the new Focus is quite decent - it's positioned along the inner edge of the front center armrest console. Just open it and you'll spot a small slot-style jack. This design prevents dashboard clutter, though personally I prefer using Bluetooth for wireless phone connection to play music, avoiding the hassle of plugging/unplugging cables. If you favor AUX for its more accurate sound quality, the port is conveniently located in the armrest - just be careful not to damage anything when rummaging after opening. If you can't find it, it might be missing from factory installation or modified - check the trunk toolkit for spare ports or verify activation in the user app's audio source settings. Focus ports are generally durable, but periodic dust cleaning is recommended to maintain smooth connection and prevent electrical leakage.
Was this review help?
4
4
Share
Expand All
EstherRose
11/28/25 2:32am
On my Focus, the AUX port is located in the small storage compartment under the dashboard, near the passenger side. Just pull out the manual drawer and you'll see the small round hole. Once opened, simply plug in your phone cable and it should work—easy to operate without worrying about complexity. The position is designed to be discreet yet accessible. If you can't find it, check whether your vehicle configuration includes the premium sound system, as it might be relocated next to the center display. Ensure the AUX cable is securely connected for clear playback without lag—new owners can quickly locate it using the manual's diagram. For daily use, don’t neglect port maintenance to avoid water damage and short circuits.
Was this review help?
10
2
Share
Expand All
More Forum Discussions

What does it mean when the ABS yellow light comes on in a Volkswagen Polo?

When the car displays the ABS light, it indicates a malfunction in the vehicle's anti-lock braking system. During emergency braking, if the wheels lock up, the vehicle may lose control and skid, preventing the driver from slowing down or adjusting the vehicle's trajectory, which poses significant safety risks. There are several conditions under which the ABS light may illuminate, each with different causes and solutions, as detailed below: Condition 1: ABS warning light stays on constantly (most common). Cause 1: The ABS speed sensor's sensing area is covered by dirt, mud, or other contaminants, affecting the sensor's ability to detect the corresponding speed signal. This prevents the ABS computer from determining the vehicle's speed and the wheel's slip rate, thus failing to issue appropriate commands to adjust braking. Solution: Clean the dirt from the speed sensor and adjust the gap between the speed sensor and the signal ring to restore normal function. Cause 2: Poor signal due to loose connections in the system wiring or poor contact in the ABS relay, leading to system failure. Solution: Check the wiring connections and reconnect any loose parts. Condition 2: ABS warning light intermittently illuminates but turns off when accelerating. Cause: When multiple vehicle electrical components are in use, the battery voltage may drop below 10.5V. As the engine speed increases, the voltage rises, causing the ABS light to turn off. This could also be due to insufficient power supply voltage to the ABS system, such as poor terminal contact or grounding issues. Solution: Check the battery's specific gravity; inspect the charging system; examine the power supply (e.g., voltage relay or poor power contact). Condition 3: ABS warning light stays on after engine start and only turns off when the engine is turned off (IGFF). Cause: Poor grounding contact in the ABS hydraulic valve body; poor electrical connection in the ABS hydraulic valve body; ABS computer malfunction. Solution: Loosen the grounding screw on the hydraulic valve body, then retighten it, cleaning the contact surface if necessary; check if the plug gap has widened; replace the ABS or ABS/ASR computer. Condition 4: ABS warning light illuminates during high-speed driving. Cause: At high speeds, the ABS computer detects a significant discrepancy between the rear and front wheel speed signals; incorrect tire or wheel rim specifications. Solution: Refer to the vehicle's tire and wheel rim specifications, as indicated on the sticker near the fuel tank cap. Condition 5: ABS warning light intermittently illuminates. Cause: Improper adjustment of the brake light switch; poor internal contact in the brake light. Solution: Start the engine, press the brake pedal, push the brake switch linkage down fully with your finger, then release the brake pedal to complete the self-setting position; replace the brake light switch if necessary.
19
5
Share

Where are the sunroof drainage holes located on the Golf 6?

The sunroof drainage holes on the Golf 6 are located at the four corners of the sunroof. Below are specific details about the Golf 6: 1. Positioning: The Golf is a compact car under the Volkswagen brand. This model has achieved excellent sales in China and is highly favored by young consumers, ranking among the top in terms of market share. 2. Configuration: The Golf is equipped with three types of engines: a 1.2-liter turbocharged engine, a 1.4-liter turbocharged engine, and a 1.6-liter naturally aspirated engine. The transmission options for this model include a 5-speed manual transmission or a 7-speed dual-clutch transmission.
19
5
Share

What is the fuel consumption of the Golf 4?

The Golf 4 generally has a combined fuel consumption of around 8-10 liters per 100 kilometers. Below is a related introduction to the Golf 4: 1. Performance: Equipped with the EA211 engine, with the assistance of TSI turbocharging technology, the 1.4T model achieves an efficient acceleration of 8.2 seconds from 0 to 100 km/h while maintaining a lower fuel consumption of 5.4L/100 km. 2. Safety: In terms of passive safety, it adopts sine curve laser welding technology; equipped with multiple passive safety features such as pre-tensioned seat belts, head and knee airbags, and ISOFIX+TopTether child seat interfaces.
14
0
Share

What is the fuel tank capacity of the Golf 4?

The fuel tank capacity of the Golf 4 is 60 liters. Below is the relevant introduction of the Golf 4: 1. Performance: Equipped with the EA211 engine, with the assistance of TSI turbocharging technology, the 1.4T model achieves an efficient acceleration of 8.2 seconds for 0-100 km/h while maintaining a lower fuel consumption of 5.4L/100 km. 2. Safety: In terms of passive safety, it adopts sine curve laser welding technology; equipped with multiple passive safety features including pre-tensioned seat belts, head and knee airbags, and ISOFIX+TopTether child seat interfaces.
8
0
Share

What Are the Causes of Engine Carbon Deposits?

Engine carbon deposits are formed due to: 1. Long-term poor driving habits, such as driving at low engine speeds with high gears; 2. The use of low-quality gasoline with high impurity content, which forms carbon deposits after combustion in the engine; 3. Aging or damage to the engine's carburetor, leading to insufficient fuel atomization before combustion, resulting in carbon deposit formation. Methods for engine maintenance include: 1. Using high-quality engine oil; 2. Using qualified coolant; 3. Regularly cleaning radiator scale; 4. Periodically removing carbon deposits from the car; 5. Timely replacement of the car's three filters; 6. Maintaining reasonable engine speeds.
20
3
Share

What does the flashing 4lo light mean?

It indicates an issue with the vehicle's four-wheel drive system. 4lo is the fault indicator light for the 4WD system. Here is relevant information: 1. When this light illuminates, you must have a mechanic use a diagnostic scanner to read the trouble code and identify the cause of the fault for targeted repairs. After completing the repairs, clear the trouble codes. 2. When the vehicle switches to low-speed cruise mode in 4WD, the 4lo light flashing is a relatively common issue. The faults causing the 4lo light to flash are complex and cannot be self-diagnosed - only by reading system data can abnormalities be detected. The fault light will turn off only after the issue is resolved.
10
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.