Where is the air filter of the Qashqai located?

2 Answers
StLucas
07/25/25 2:33pm
The air filter of the Qashqai is located behind the glove box on the passenger side. Additional information: Function of the air filter: The air filter serves a filtration purpose, cleaning the air entering the cabin from outside, thereby improving air purity. The typical filtration targets include impurities in the air, such as tiny particles, pollen, bacteria, industrial exhaust, and dust. The air filter prevents these substances from entering the air conditioning system, protecting the system from damage, providing a good air environment for passengers, safeguarding their health, and preventing window fogging. Cleaning tips: If the filter is dirty, clean it by blowing compressed air from the opposite side. Hold the air gun about 5 cm away from the filter and blow at a pressure of 500 kPa for approximately 2 minutes. The air filter tends to accumulate a lot of dust, and blowing compressed air can remove the loose dust.
Was this review help?
16
2
Share
Elena
08/11/25 9:08pm
I've been driving the Qashqai for several years and have some experience. The location of the Qashqai's cabin air filter is not hard to find—it's right behind the glove box on the passenger side. First, open the glove box and empty its contents. You'll see some plastic clips securing the bottom of the box. Gently press the clips, and the entire glove box can be removed. After removing it, look inside, and you'll find a rectangular slot near the center under the dashboard—that's where the cabin air filter resides. I've replaced it several times myself. Remember to check it every six months or after driving 10,000 kilometers. Too much dust buildup can affect cooling efficiency and may cause unpleasant odors. When replacing it, simply pull out the old filter and insert the new one, aligning the arrow direction. It's simple and cost-effective. If it's your first time, be careful not to force the clips, as breaking them would require a trip to the repair shop.
Was this review help?
4
1
Share
Expand All
More Forum Discussions

What is a car with poor brakes called?

Tesla is the car with poor brakes. Here is an introduction about Tesla: Introduction to Tesla: Tesla is an American electric vehicle and energy company that manufactures and sells electric vehicles, solar panels, and energy storage equipment. Its headquarters is located in Palo Alto, California. It was founded on July 1, 2003, by Martin Eberhard and Marc Tarpenning, who named the company "Tesla Motors" in honor of the physicist Nikola Tesla. History of Tesla: Tesla's initial new energy vehicle startup team mainly came from Silicon Valley, using IT concepts to build cars rather than the traditional approach represented by Detroit's automakers. Therefore, Tesla's creation of electric vehicles is often seen as a story of a Silicon Valley upstart challenging Detroit's giants.
14
3
Share

What causes the brake lights to stay on and not turn off?

Brake lights staying on and not turning off is usually caused by a faulty brake switch. Here is some relevant information about car brake lights: Working principle: Brake lights are an important component of rear lights, distributed one on each side of the rear light assembly. The red light they emit serves as a warning signal, illuminating when the brake pedal is pressed (including when using the handbrake). Function: Brake lights alert following vehicles that the car is slowing down or stopping, allowing them to prepare in advance and take evasive action. Modern brake lights are typically fog lights that can penetrate thick fog, providing better warning effectiveness.
8
3
Share

Why Can't the Brake Be Depressed and the Car Won't Start?

Brake can't be depressed and the car won't start for the following reasons: Steering wheel lock: After inserting the key, turn it in the normal ignition direction, but not all the way. Gently turn it to the battery switch position. Once the car is powered on, gently move the steering wheel left and right. If the steering wheel can move, then depress the brake and start the car. Remember to straighten the steering wheel when parking in the future to avoid the same problem recurring. Low car battery power: In this case, after inserting the key, turn it to the battery switch position and observe whether the dashboard behind the steering wheel shows power. If unsure, turn on the headlights to confirm again. If the headlights don't light up, it confirms the battery is dead.
17
1
Share

What are the effects of water entering the brake system?

The impact of water entering the brake system is that it can cause brake lag, leading to vehicle deviation during braking and potential accidents. Below is an introduction about brakes: Introduction: As the name suggests, it is a mechanical braking device that can slow down the vehicle, also known as a decelerator. Function: The car brake pedal is located below the steering wheel. Pressing the brake pedal causes the brake lever linkage to be pressurized and transmitted to the brake shoes on the brake drum, which then clamp the brake disc to slow down or stop the vehicle. Category: The manual brake in a car is located next to the gear shift and is connected to the brake lever. Common types also include bicycle brakes, which rely on rod-shaped brakes fixed to the frame or disc-mounted caliper brakes to slow down.
12
5
Share

What is the reason for the occasional feeling of a loose brake pedal?

Occasionally feeling a loose brake pedal accompanied by a decrease in braking force indicates a malfunction in the brake system. Below is relevant information about brakes: Introduction: As the name suggests, it is a mechanical braking device that slows down the vehicle, also known as a decelerator. Structure: The car brake pedal is located below the steering wheel. Pressing the brake pedal causes the brake linkage to be pressurized and transmitted to the brake shoes on the brake drum, which then clamp the brake disc. Function: To slow down or stop the vehicle. The manual brake in a car is located beside the gear shift and is connected to the brake lever. Common examples also include bicycle brakes, which rely on rod-shaped brakes fixed to the frame or disc caliper brakes to decelerate.
20
3
Share

What is the material of brake discs?

The material of brake discs adopts the domestic gray cast iron 250 standard, abbreviated as HT250, which is equivalent to the American G3000 standard. The requirements for the three main chemical elements are: C: 3.1~3.4, Si: 1.9~2.3, Mn: 0.6~0.9. More details are as follows: Mechanical performance requirements: tensile strength >=206MPa, bending strength >=1000MPa, deflection >=5.1mm, hardness should be between 187~241HBS. Alternative names: In English, brake discs are usually referred to as BRAKE-DISC or BRAKE-ROTORS, while brake drums are called BRAKE-DRUM. Additionally, in southern China, brake discs are also known as brake discs or brake rotors. In fact, they all refer to the same thing.
7
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.