Where is the air conditioning outlet of the X-Trail located?

1 Answers
Elise
07/30/25 10:53am
The drainage outlet of the X-Trail's air conditioning system is designed at the lowest point below the condenser in the cabin. Once you locate the condenser inside the cabin, you will find the drainage outlet. Function of the air conditioning drainage outlet: The purpose of the air conditioning drainage outlet is to expel water condensed during the heat exchange process when the air conditioning is in use. The evaporator continuously absorbs moisture from the surrounding air, which condenses into water and is discharged through the drainage outlet. This explains why a puddle of water often forms under the car after the air conditioning has been running for a while. Many new car owners may mistake this for a car leak, but there's no need to worry as long as you confirm whether the air conditioning was turned on. Consequences of a blocked drainage outlet: During the cooling process, the car's air conditioning system produces condensed water, and the drainage pipe for this water is located under the chassis. During the rainy season, exposure to mud and standing water can cause the drainage outlet to become blocked. The consequences are similar to those of a blocked engine compartment drainage outlet—water may flow back into the car, leading to water accumulation on the floor.
Was this review help?
8
3
Share
More Forum Discussions

Which way should the steering wheel turn when reversing to the left?

When reversing to the left, the steering wheel should be turned to the right. Here is a partial introduction about reversing to the left: Technique: Engage reverse gear, slowly release the clutch pedal to start reversing in a semi-engaged state. Look at the right rear window, and when the 3ccc mark on the right rear window glass aligns with the right line of the garage, immediately and evenly turn the steering wheel fully to the right. Look at the left rearview mirror, adjust the vehicle's position by observing both side mirrors, and reverse into the garage. Precautions: To exit the garage, engage first gear, slowly release the clutch pedal, and start moving forward in a semi-engaged state.
16
4
Share

Correct Connection Method for Car Battery Jumper Cables?

Correct connection method for car battery jumper cables is to clamp the red cable to the positive terminal of the battery. Here are some introductions about car battery jumper cables: Battery Jumper Cables: Clamp one end of the red cable to the positive terminal of the dead battery, connect the jumper cable, then clamp the other end of the red cable to the positive terminal of the live car's battery. Clamp one end of the black cable to the negative terminal, and the other end to the negative terminal of the live car's battery or to the car body or any metal engine part. Precautions: Ensure all connection points are tightly clamped, as the starting current is high. Remove the protective cover from the positive terminal of the car battery, clamp one end of the red cable (+) to the positive terminal of the battery, then proceed to connect the jumper cables.
6
5
Share

Where is the USB port in the Avancier?

The USB port in the Avancier is located on the side or rear of the center console panel. Here is some relevant information about the Avancier: Exterior: The Avancier is a new mid-size luxury SUV launched by GAC Honda. With a design concept that transcends the times, the Avancier's exterior embodies a majestic and dynamic style, combining strength and beauty. Features like the bold front grille, eagle-wing LED headlights, and robust body lines highlight its uncompromising and sharp character. Interior: Inside, the Avancier boasts a symmetrical dashboard wrapped in soft materials and wood trim. A large adjustable floating touchscreen dominates the center, enhancing the technological ambiance. The vehicle comes equipped with practical features such as a one-touch start system, electronic parking brake, heated seats, rear parking sensors, and vehicle stability assist. Additional comfort and tech features include rear automatic air conditioning, a rear center armrest with entertainment system controls, and rear sunshades.
5
3
Share

Brief Introduction to the Causes of Drive Axle Oil Leakage

Drive axle oil leakage is caused by loosening or damage. Here are some common causes: Loosening: Possible causes of drive axle loosening include: loose oil filler cap or drain plug; worn or hardened oil seal, incorrectly installed oil seal, misalignment between oil seal and shaft neck, or groove formation on the oil seal shaft neck; deformed, rough, hardened, or damaged mating surfaces. Additionally, the drive axle must withstand vertical forces, longitudinal and lateral forces acting between the road surface and the frame or body, as well as braking torque and reaction forces. Damage: Possible causes of drive axle damage include: damaged fastening screws; blocked vent hole; casting defects or cracks in the axle housing; excessive gear oil leading to increased internal pressure during operation and gear oil seepage.
14
2
Share

How to cancel the next oil change maintenance reminder?

Follow the instrument panel's vehicle condition check prompt to reset it. Below is relevant information about the maintenance light: 1. Introduction: The maintenance light is a reminder function set by the manufacturer to prompt the owner to perform maintenance at certain mileage or time intervals, displayed through instrument or screen messages or indicator lights. Resetting the maintenance light means clearing the reminder information after maintenance is completed, essentially resetting the information; 2. Function: The maintenance light records the mileage of important components, acting like a timer in a sprint race to remind the owner and automotive maintenance personnel. If the owner replaces related components but does not reset the light, it will not affect the vehicle's performance but may cause inconvenience for the next component replacement, as the exact usage time of the new component cannot be accurately tracked.
2
1
Share

How to Choose Between BMW 3 Series and Mercedes-Benz C-Class?

BMW 3 Series or Mercedes-Benz C-Class owners should make their purchase decision based on their own needs. The following introduces the differences between the two: 1. Different exterior styles: The new BMW 3 Series maintains a relatively youthful and sporty style overall, which is somewhat similar to Mercedes-Benz. However, most people would feel that the Mercedes-Benz C-Class appears more upscale, giving off a more luxurious vibe on the road. The Mercedes-Benz C-Class exudes a sense of elegance and dignity. Its front-end design comes in two variants: sporty and luxurious. Due to the C-Class's body lines resembling those of the S-Class, both the sporty and luxurious designs blend perfectly without appearing out of place. 2. Interior: The difference between high-end and low-end models of the BMW 3 Series is very significant in terms of interior, while the gap between high-end and low-end models of the Mercedes-Benz C-Class is relatively small.
12
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.