Where is the air conditioning filter of Jianghuai truck located?

2 Answers
JulietAnn
07/28/25 3:06pm
Jianghuai truck air conditioning filter is located under the storage box in front of the co-pilot. The following is part of the introduction about the air conditioning filter: 1. The air conditioning filter is an ideal material for various high-end cars, sedans and commercial vehicles as automobile air conditioning filters; The filter can efficiently filter and adsorb particulate impurities to achieve oil filtration and air purification performance, and can also well remove organic gases. 2. The air conditioning filter filters the air entering the compartment from the outside to improve the cleanliness of the air. The general filtering substances refer to the impurities contained in the air, such as tiny particles, pollen, bacteria, industrial waste gas and dust.
Was this review help?
10
2
Share
MacPiper
08/11/25 10:47pm
I've been driving a JAC truck for many years and have replaced the cabin air filter several times by myself. For most JAC trucks, the filter is located behind the glove compartment on the passenger side. You need to release the clips on both sides of the glove compartment and remove it entirely to access the filter. Some newer models might have it under the dashboard, but it's generally in the passenger side area. I recommend checking the manual to confirm the model before replacement - buying the wrong size filter would make all your effort wasted. When removing the old filter, pay attention to the arrow direction, and install the new filter following the same orientation. I always replace it before summer, otherwise the AC blows dusty air. DIY replacement saves at least 100 yuan compared to going to a repair shop, and you can clean fallen leaves from the blower wheel while you're at it.
Was this review help?
15
5
Share
Expand All
More Forum Discussions

How to Set the Best Sound for the Envision Audio System?

In the Envision control panel, adjust the vehicle's audio center slightly forward or backward, then increase the volume. When set to the appropriate position, you will achieve the best sound effect. Below are relevant details about the Envision: 1. Configuration: The Buick Envision is equipped with a BOSE audio system, delivering rich sound quality with surround effects. Additionally, the Envision uses hidden microphones to detect interior noise waves and counteracts them by emitting opposing sound waves through the speakers. BOSE is one of the largest speaker manufacturers in the U.S., headquartered in Massachusetts, with hundreds of engineers dedicated to research and development. It is a wholly independent company. 2. Audio Adjustment: For Envision audio adjustment, EQ settings are sufficient. NORMAL mode provides an unaltered sound effect with no boosts or cuts across any frequency range, ideal for those who prefer original sound. ROCK mode significantly enhances both high and low frequencies, delivering powerful bass for a strong rhythm and clear, sometimes sharp highs. POP mode follows a curve similar to ROCK but slightly reduces low frequencies while enhancing highs for better instrument performance. JAZZ mode boosts low frequencies and the 3-5kHz range, enhancing the live experience. CLASSIC mode enhances both high and low frequencies, emphasizing instrument performance and soundstage, making it perfect for grand classical music performances.
7
4
Share

What are the types of cranes?

Cranes are used for lifting equipment, emergency rescue, hoisting, machinery, and rescue operations. Commonly used cranes include truck cranes, crawler cranes, and tire cranes. The specific details are as follows: Cranes are classified by mobility into: 1. Mobile types: truck cranes, crawler cranes, overhead cranes, etc. 2. Fixed types: dock cranes, tower cranes, gantry cranes, etc. Additional information: Safety devices of cranes: 1. Load indicator: An angle indicator installed near the driver's position at the base of the boom, which changes with the boom's elevation angle, reflecting the angle between the boom and the ground. By knowing the elevation angle at different positions of the boom and referring to the crane's performance table and performance curve, one can determine the reference values such as the radius, lifting capacity, and lifting height at a specific elevation angle. 2. Over-hoisting limiter: A safety device installed on the pulley group at the end of the boom to limit the lifting height of the hook and prevent over-hoisting accidents. It ensures that when the hook reaches the limit position, an alarm signal is automatically triggered or the power source is cut off to stop the lifting, thereby preventing over-hoisting.
5
3
Share

Which company produces Nissin brake calipers?

The company that produces Nissin brake calipers is Nisshinbo Brake Inc., with its parent company being NISSHINBO Holdings Inc. NISSHINBO is involved in various businesses including textiles, brake components, paper manufacturing, machinery, chemicals, electronic technology, real estate, and even international logistics. Functions of brake calipers: Brake calipers are designed to decelerate moving wheels, bring them to a stop, or maintain a stopped state. They are typically used in disc brake systems and are the protruding parts on the outer side of the brake pads that enhance braking performance. Calipers are equipped with dust boots to prevent impurities from damaging the pistons and also include anti-rattle clips to secure the brake pads, reducing noise during daily use. Classification of caliper colors: Black brake calipers are the most common and are generally used in Porsche's entry-level models such as the Boxster and base versions of the Cayenne. Silver brake calipers are an upgraded version of black ones, usually found in enhanced versions of entry-level models and many mid-level models, such as the Carrera in the 911 series. Red brake calipers represent a new brake system characterized by larger brake disc sizes. For example, the Cayman S sports version comes standard with a red-caliper brake system. Red brake calipers are also quite common in Porsche's mid-range vehicles.
15
3
Share

Is it safe if the car sensor is broken?

Damage to the car sensor can directly affect driving safety to a certain extent. If the wheel speed sensor is damaged, it not only causes slight deviations in the speed display on the dashboard but also leads to unstable engine idling and reduced acceleration performance. The main sensors in a car are as follows: 1. Airflow sensor: The airflow sensor is usually installed between the air filter and the throttle body to measure the amount of air inhaled by the engine, converting it into an electrical signal provided to the ECU as a reference signal for fuel injection timing. If it malfunctions, the car may experience idling vibrations, weak acceleration, increased fuel consumption, and black smoke from the exhaust pipe, thereby affecting the engine's performance. 2. ABS sensor: The ABS sensor is typically located near the wheel bearing, outside the hub bearing and inside the brake disc, to monitor the vehicle's speed. During emergency braking, it feeds the wheel speed back to the braking system, which then controls the wheel's rotation to achieve optimal braking effect. If it fails, the ABS will not function, causing the wheels to lock up during emergency braking, leading to skidding and loss of control. 3. Throttle position sensor: The throttle position sensor is installed on the throttle body to detect the throttle opening. It works in conjunction with the throttle via a lever mechanism, measuring the throttle opening angle's voltage signal and transmitting it to the ECU as a reference signal for fuel injection volume and ignition timing correction. If it malfunctions, it can result in abnormal engine idling, engine vibrations, and delayed acceleration response.
18
1
Share

Why does the car fail to start on the first attempt when cold but succeeds on the second try?

There are several reasons why a cold car fails to start on the first attempt but succeeds on the second try: 1. Check the spark plugs: Inspect the ignition and combustion condition of the spark plugs. The ignition energy of the spark plugs directly affects combustion in the cylinder, thus impacting startup. Therefore, the first step is to check the spark plugs. 2. Clean the fuel injectors: Poor atomization of the fuel injectors also affects combustion and can cause difficulty in starting. A key function of fuel injectors is to atomize fuel for complete combustion. 3. Check fuel pressure: Insufficient fuel pressure or poor supply can lead to inadequate fuel injection, affecting startup. A clogged fuel filter or a leaking pressure valve on the fuel pump can cause fuel pressure loss in the fuel lines, requiring pressure to be rebuilt each time the car starts. This is the most critical and easily overlooked issue. 4. Charcoal canister solenoid valve: This is another easily overlooked component. The charcoal canister solenoid valve controls the entry of fuel vapor from the fuel tank into the engine for combustion. If too much fuel vapor enters the engine, it can cause an overly rich air-fuel mixture, leading to difficulty in starting. 5. Excessive carbon buildup can also cause starting difficulties: This is the hardest issue to address. For naturally aspirated engines, carbon buildup under normal usage within 80,000 kilometers usually doesn’t have a significant impact. However, direct-injection turbocharged engines tend to have more severe carbon buildup by 80,000 kilometers compared to naturally aspirated engines.
3
2
Share

What is the method to reset the maintenance reminder light on the Ford Kuga?

Sit in the car, close the door, and turn the ignition to the second position. Then press the accelerator and brake pedals simultaneously to the floor. After about 10 seconds, the information center will display a prompt. Continue holding the pedals for about 30 seconds, and the information center will show "OIL-LIFE-RESET-COMPLETE," indicating the operation is complete. Additional information is as follows: 1. Vehicle Introduction: The Ford Kuga inherits over half a century of research, design, manufacturing, and tuning expertise from the Ford SUV family. Its exterior is more sporty and stylish, and the center console features a new 10-inch LCD screen paired with an advanced internet-based car intelligent system. The optimized rear seating space improves knee room for passengers, enhancing overall comfort. 2. Performance: The EcoBoost® series engines are known for their powerful, quick-start, and sustained acceleration capabilities. Particularly, the class-leading EcoBoost® 245 engine utilizes twin-scroll turbocharging technology, enabling earlier turbo engagement and more rapid power delivery. It delivers a maximum power of 180 kW at 5500 rpm and a peak torque of 350 Nm between 1750-4000 rpm, paired with an intelligent AWD system.
9
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.