···
Log in / Register

Where is the air conditioning filter located in the Changan CX30?

1 Answers
AmaraAnn
09/07/25 4:53am
The air conditioning filter in the Changan CX30 is located beneath the wiper panel in the engine compartment. You'll need to remove the wiper panel to access it. Since this involves removing the wipers, it's recommended to have it replaced at a 4S shop or auto repair shop. Here's more information about car air conditioning filters: 1. Manufacturers generally recommend replacement every 20,000-30,000 kilometers, but in practice, replacement is usually needed every 10,000-20,000 kilometers. This is because maintenance typically involves cleaning with high-pressure air, and it's advisable to avoid using the external circulation mode during normal operation due to excessive road dust. 2. In areas with high windblown sand or severe smog, the replacement interval can be appropriately shortened to every 5,000-7,500 kilometers. Generally speaking, how often a car's air conditioning filter needs to be replaced depends on usage conditions. For ordinary urban family cars, replacement is typically needed every six months to a year.
Was this review help?
7
2
Share
More Forum Discussions

How to Reset the Maintenance Light on the 2020 Buick Excelle?

Press and hold the reset button "A" while stepping on the brake. Turn the ignition switch to "on" without starting the car. The characters "INSP" will flash or the display will blink. Continue holding the reset button "A" until "..." appears on the display. Release the reset button "A" and take your foot off the brake. Turn the ignition switch back to the "Off" position. The reset process is complete. Note that not all models can be reset manually; some models require code clearing.
11
3
Share

How to restart the Audi MMI system?

Press the car button at the bottom left, the large knob in the middle, and the button at the top right next to the large knob to restart the MMI. Hold for about 6 seconds, and the system screen will turn off and then automatically restart. If you find that it cannot restart smoothly each time, it is related to these buttons. Hold for about 2 seconds to forcibly shut down the MMI system. After shutting down, press and hold the power button to turn it on again. If the above methods cannot restart the system smoothly, it is time to go to the 4S store for replacement and repair in a timely manner.
9
0
Share

What to Do When the Car Key Fob Won't Open the Door?

Here are the solutions when the car key fob fails to open the door: 1. Replace the battery; 2. Use the mechanical key to open the door; 3. Inspect and repair the sensor module. The steps to replace the key fob battery are: 1. Remove the mechanical key; 2. Insert a flat-head screwdriver into the "open" slot at the bottom and gently pry upwards and downwards; 3. Once a gap appears, use the screwdriver to carefully pry open the key fob along the gap; 4. Remove the old battery and replace it with a new one. The reasons why the car key fob may not open the door include: 1. Insufficient battery power in the key fob; 2. The car battery is dead, preventing the key fob from being detected; 3. Issues with the key fob or sensor module.
18
4
Share

How to release the windshield washer fluid in Haval M6?

To release the windshield washer fluid in Haval M6, pull the lever on the right rear side of the steering wheel toward the driver's direction and hold for two seconds. The Haval M6 is a compact 5-door, 5-seat SUV with the following dimensions: length 4664mm, width 1830mm, height 1729mm, and a wheelbase of 2680mm. It is equipped with a 1.5T turbocharged engine and a 6-speed manual transmission, delivering a maximum power of 110 kW at 5600-6000 rpm and a peak torque of 210 Nm at 1800-4400 rpm. The drivetrain configuration is front-engine, front-wheel drive. The front suspension uses MacPherson strut independent suspension, while the rear suspension employs double-wishbone independent suspension.
15
5
Share

How to Repair a Dented Car Rocker Panel?

Insert the hot melt glue stick from the back of the glue gun, ensuring the stick is fully inserted. Plug the glue gun into a power outlet, set the temperature to the highest level, and preheat for 3-5 minutes until the hot melt glue is completely melted. Select a suitable traction washer based on the diameter of the dent, then pull the glue gun trigger to coat the traction washer with melted glue. Gradually, the dent will rise. If any raised areas appear after pulling, use a rubber hammer and a specialized wooden pen to gently tap until the dent blends into the car paint.
12
5
Share

What to do if the roof light of the Lavida stays on and cannot be turned off?

First, open the rear door of the car and sit in the middle of the back seat. Look up, and you will find the switch for the roof light directly above the seat. The button generally has three modes: ON (always on), DOOR (on when the door is open and off when closed), and OFF (off). OFF means the light is turned off; selecting this mode will keep the roof light off and it will not illuminate.
20
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.