Where is the air conditioning filter located in a BMW 740?

1 Answers
Kieran
07/29/25 11:38pm
The air conditioning filter in a BMW 740 is located inside the glove compartment on the passenger side. Air filter applications: An air filter is a type of filter. It is mainly used in engineering vehicles, automobiles, agricultural vehicles, laboratories, sterile operating rooms, and various precision operating rooms as an air filtration device. Effects of unfiltered air: When the engine is running, it needs to intake a large amount of air. If the air is not filtered, the dust suspended in the air will be drawn into the cylinders, accelerating the wear of the piston assembly and cylinders. Larger particles entering between the piston and cylinder can cause severe "cylinder scuffing," which is particularly serious in dry and sandy working environments. Function of the air filter: The air filter is installed in front of the carburetor or intake pipe to filter out dust and sand particles from the air, ensuring that sufficient and clean air enters the cylinders.
Was this review help?
11
3
Share
More Forum Discussions

How to Set Up Remote Window Control?

Method to set up remote window control: Turn on the ignition switch, use the switch to open the power window halfway, then fully push the switch until the power window is completely closed, and keep holding the switch for 3 to 5 seconds after the window is fully closed. If you forget to close the windows after getting out of the car and the distance is too far to walk back, simply take out the key and lightly press the lock button on the remote key, and all four windows and the sunroof will automatically close. The power window settings should be reconfigured under any of the following circumstances: 1. Replacement or disassembly of the multiplex network master switch, multiplex network switch, multiplex network door ECU harness, or power window regulator motor; 2. Replacement of fuses or relays related to power window control. Unless the power window regulator motor is reset, the AUTO operation function, anti-pinch function, and remote control operation function of the multiplex network master switch will not work.
10
0
Share

How to Replace the Remote Battery for Volvo S90?

Steps to replace the remote battery for Volvo S90: 1. Remove the mechanical key. Open the panel to see the mechanical key, which is fixed between two panels via a slot. Press the small black button on the top of the key sideways and push the logo side forward to open it; 2. Press the protruding button on the back panel sideways and pull the back panel upward by 5mm. At this point, the back panel will detach from the main body and can be removed; 3. Rotate the battery cover to the 'ope' position, then remove the battery cover from the gap and take out the O-ring seal; 4. Now you can see the coin battery, which is model CR2032. Simply remove the old battery and replace it with a new one. The Volvo S90 is a luxury sedan under the Volvo brand. The dimensions of this car are 5090mm in length, 1879mm in width, 1450mm in height, with a wheelbase of 3061mm.
14
0
Share

What to Do When the Steering Wheel Pulls to the Left When Braking?

The solution to the steering wheel pulling to the left when braking is to perform a four-wheel alignment. Four-wheel alignment is based on the four-wheel parameters of the vehicle, adjusting them to ensure good driving performance and a certain level of reliability. Front wheel alignment includes four aspects: caster angle, kingpin inclination angle, camber angle, and toe-in. Rear wheel alignment includes camber angle and toe-in for each rear wheel. Reasons for the steering wheel pulling to the left: severe uneven tire wear, especially when the diameter difference between the inner and outer rear tires is significant, leading to more severe irregular braking deviation; uneven tread depth on both sides of the tires, which can cause the car to tilt to one side—it's best to use tires of the same model.
14
5
Share

Where is the engine number located on the Santana?

The engine number of the Santana is located in the engine compartment, between the battery and the brake master cylinder. On the front of the engine, there is a small black block with three sets of numbers and letters. The 17-digit one is the vehicle identification number (VIN), and the 11-digit one is the engine number. The number of digits in the engine number varies by brand, with common engine numbers typically being between 7 and 8 digits. The Santana is a brand car produced by Volkswagen in California, USA. The new generation of this model has dimensions of 4475 mm in length, 1706 mm in width, and 1469 mm in height, with a wheelbase of 2603 mm. The new Santana is equipped with a 1.5-liter naturally aspirated engine, coded EA211DIf, which delivers a maximum power of 82 kW and a maximum torque of 145 Nm.
14
4
Share

Where is the transmission oil filler port of Dongfeng Fengshen AX7?

Dongfeng Fengshen AX7 transmission oil filler port is located on the side cover of the transmission. Transmission oil is a lubricant used to keep the gear system clean, providing lubrication to extend the lifespan of the transmission components. It offers effective lubrication even in low-temperature conditions and reduces oil loss under harsh operating conditions. The Dongfeng Fengshen AX7, developed and manufactured by Dongfeng Fengshen, is a self-owned brand SUV model. The dimensions of this vehicle are 4645 mm in length, 1880 mm in width, and 1690 mm in height, with a wheelbase of 2715 mm. The Dongfeng Fengshen AX7 has been upgraded with a new starry sky grille, electric lumbar support for the driver's seat, welcome memory function for the driver's seat, and stepless adjustment for the rear seat angle.
17
2
Share

What is the wading depth of the Model 3?

The wading depth of the Model 3 should not exceed half the height of the tires. Definition of vehicle wading depth: The wading depth of a vehicle is determined by the height of the engine air intake. For most compact and small cars with low ground clearance, the air intake position serves as the benchmark when driving through waterlogged roads. The function of the air intake is to draw in air. If the water depth exceeds the height of the air intake, a large amount of water will be sucked into the engine, causing severe damage to the vehicle. Symptoms of water entering the vehicle's air intake: When the engine air filter element gets soaked, it increases air intake resistance and allows water to enter the combustion chamber. This prevents the spark plugs from igniting, and if water enters the distributor cap, it disrupts the normal ignition function, leading to the vehicle stalling while driving.
15
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.