···
Log in / Register

Where is the ACC fuse located in the Hyundai Verna?

3 Answers
DavidMarie
07/24/25 10:41pm
The ACC fuse of the Hyundai Verna is located inside the fuse box. There are two fuse boxes in the Hyundai Verna, one is located inside the dashboard support bracket on the driver's side, and the other is located near the battery in the engine compartment. To prevent short circuits, vehicles are usually equipped with fuses. Automotive fuses can be divided into blade-type fuses, glass tube fuses, and fork-type fuses. Their function is to quickly blow when the circuit current exceeds twice the rated current of the fuse, thereby protecting the circuit. The ACC function in a car refers to the power supply for auxiliary electrical appliances. Generally, there are three modes when starting a vehicle: off, auxiliary electrical appliances powered, full vehicle powered, and start. The so-called auxiliary electrical appliances refer to devices such as the radio and lights. When the vehicle is in ACC mode, the radio and interior lights can be used normally, but the air conditioning and windows cannot be opened. To control the air conditioning or windows, the key needs to be turned to the full vehicle power position.
Was this review help?
16
3
Share
DiZane
08/10/25 10:16am
As someone who has worked on cars for many years, I'm very familiar with the location of the Hyundai Verna's ACC fuse. It's located in the dashboard area below the driver's seat, near your right foot. You'll need to bend down to find a small plastic cover, usually marked with a fuse box icon. After lifting the cover, there's a color-coded diagram or label on the inner wall indicating all fuse numbers and functions. The ACC fuse is typically labeled as ACC or ACCESSORY, usually numbered between F21 to F25. If your cigarette lighter or charging port stops working, it's likely this fuse has blown. Common causes include device short circuits or current overload. When replacing, always use a new fuse with the same amperage, such as a 15A fuse. Remember to turn off the engine before operation, and use special tweezers to gently remove the bad fuse and insert the new one. Regular fuse checks can prevent circuit failures - I recommend keeping spare fuses in your glove compartment for emergencies. Once you're familiar with the location, the whole process takes less than five minutes. If unsure, consulting your vehicle manual is the safest approach.
Was this review help?
6
4
Share
Expand All
AthenaMarie
09/26/25 6:33am
I've been driving my Hyundai Verna for several years, and that experience with the blown ACC fuse taught me its location. It's right under the driver's seat, beneath a small plastic cover near your right foot. After lifting the cover, you'll see a row of fuses with a diagram on the lid indicating ACC is fuse number F23. If your cigarette lighter suddenly stops working, chances are this fuse is the culprit. In my case, it blew due to a short circuit from a charger, so I replaced it with a new 15A fuse. The process is simple: turn off the car's power, use small pliers to remove the faulty fuse, and insert the new one. During car washes, I make it a habit to glance at the fuse box to keep it clean. The location isn't hard to find, and I recommend new car owners take some time to familiarize themselves with the diagram to avoid mistakes. Understanding this small detail saves you a trip to the repair shop and unnecessary expenses. Spare parts can be bought at auto parts stores for just a few bucks. Maintaining healthy circuits is a money-saving habit, especially during long trips when the cigarette lighter gets frequent use.
Was this review help?
6
0
Share
Expand All
More Forum Discussions

Is it okay if the car scraped the chassis?

If the car scraped the chassis without any fluid leakage or mechanical deformation, it should be fine. The function of the chassis is to support and install the car engine and its various components and assemblies, forming the body shape, receiving the power from the engine to make the car move and maintain normal driving. The composition of the car chassis: it consists of the transmission system, steering system, driving system, and braking system. The maintenance methods for the car chassis are: 1. Check the oil condition of each important assembly in time; 2. Pay attention to the wear of brake pads and clutch plates; 3. Regularly perform four-wheel alignment; 4. Pay attention to the tire pressure and wear condition.
8
5
Share

How to Replace a Faulty Spark Plug?

To replace a faulty spark plug, follow these steps: 1. Wait for the engine to cool completely, open the hood, unplug the high-voltage pack connector, and remove the fixing bolts; 2. Use a socket wrench to loosen the nuts by turning counterclockwise; 3. Use a magnetic rod to extract the spark plug; 4. Attach the new spark plug to the magnetic rod and insert it into the hole; 5. Reassemble by following the above steps in reverse order; 6. Start the engine to check if the spark plug is functioning properly. The reasons for a faulty spark plug include: 1. Insufficient spark energy during ignition; 2. Excessive air-fuel ratio in the fuel mixture; 3. Overheating of the engine; 4. Dirty air filter; 5. Excessive idle speed; 6. Severe carbon buildup and use of low-quality gasoline; 7. Damaged valve oil seal or crankcase ventilation valve.
4
4
Share

Why is it difficult to engage reverse gear in a manual transmission?

The reasons why it is difficult to engage reverse gear in a manual transmission are: 1. The gear is not engaged and is in neutral; 2. The gear switch of the transmission is faulty; 3. The clutch is not fully depressed; 4. The synchronizer is not installed, causing the teeth to misalign with the gear; 5. The handbrake is not released, leaving the car in manual braking state. The steps to start a manual transmission car are: 1. After starting the car, press the clutch pedal all the way down with your left foot to completely disengage the clutch; 2. Shift the transmission into first gear; 3. Press or lift the electronic handbrake button; 4. Ensure safety by observing the road and other vehicles or pedestrians; 5. Continue to hold the clutch pedal with your left foot to keep the clutch disengaged, press the accelerator pedal with your right foot, and slowly release the clutch pedal with your left foot.
14
5
Share

What is the Volkswagen Teramont 330TSI?

Volkswagen Teramont 330TSI is the Volkswagen Touareg 330TSI model. Here are the specific details about the Volkswagen Touareg: 1. Powertrain: The Touareg is equipped with three powertrain options, including a 2.0T high/low-power version and a 2.5T V6 engine. The Touareg 330TSI model features a 2.0T engine with a maximum power output of 186 horsepower and a maximum torque of 320 Nm, paired with a 7-speed dual-clutch transmission. The power of the 330TSI model can meet the basic needs of daily driving. 2. Features: The vehicle comes with a multimedia information display that supports the App-Connect smartphone integration platform, compatible with Apple CarPlay and Android Auto. It also includes adaptive cruise control, lane keeping assist, blind spot monitoring, collision warning, heated steering wheel, front seat heating/ventilation, and a panoramic sunroof.
19
3
Share

What Causes the Jerking Sensation When Releasing the Clutch After Shifting Gears?

The reasons for experiencing a jerking sensation when releasing the clutch after shifting gears are: 1. Jerking during upshifting: The transmission's response speed is not fast enough, and the upshift speed cannot keep up with the driver's throttle input, resulting in a jerking sensation during gear changes. 2. Jerking during downshifting: When the driver releases the accelerator pedal or presses the brake pedal, the alternator starts working, placing a load on the engine and causing a mismatch between the engine speed and the clutch disc speed, leading to a jerking sensation. The working principle of the clutch is: 1. The torque generated by the engine is transmitted to the driven disc through the friction between the flywheel, pressure plate, and the contact surface of the driven disc. 2. When the driver depresses the clutch pedal, the diaphragm spring's large end moves the pressure plate backward through mechanical linkage, separating the driven components from the driving components.
20
4
Share

How to Turn Off a Motorcycle Alarm?

There are several methods to turn off a motorcycle alarm: you can directly use the key to turn on the power switch, which will deactivate the alarm state. When the key is not available, simply unplug the power connector and then plug it back in to deactivate the alarm state. Below is additional information about power locks: 1. By voltage: Power locks can be categorized into low-voltage power locks and high-voltage power locks based on voltage levels. Low-voltage power locks are mainly used in small appliances, electric toys, and electric vehicles. High-voltage power locks are primarily used in machine tools, elevators, etc. 2. By the number of controlled circuits: Power locks can be divided into single-circuit power locks, dual-circuit power locks, and multi-circuit power locks. A single-circuit power lock can only control one circuit. A dual-circuit power lock can simultaneously control two circuits.
17
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.