Where is the ABS pump located in a BMW 7 Series?

How to Tell When the Steering Wheel is Centered?

Methods to determine if the steering wheel is centered are as follows: 1. Based on the logo: You can judge by the logo on the steering wheel. When the logo is directly facing the driver, it means the wheel is centered. If there is any deviation, it indicates the wheel is not centered. 2. Based on the number of turns: You can determine if the steering wheel is centered by counting the number of turns. While moving the vehicle, turn the steering wheel and remember how many turns it takes from the fully locked position to the center. Then, turn it back the same number of turns to return to the center position, thus centering the steering wheel. 3. Check the tire direction: Drive a short distance in one direction. If the car does not deviate, it means the steering wheel is centered. If there is any deviation, it means the wheel is not centered yet, so you should adjust the steering wheel based on the degree of deviation.

9

3

Share

Can motorcycles go on highways in Hainan?

Motorcycles are not allowed on highways in Hainan. Here are some precautions for motorcycle riding: Running-in period: During riding, it should be noted that the engine speed during the running-in period should not exceed 50% of the maximum power speed, and the maximum speed should not exceed 75%. After the running-in period: The maximum riding speed should not exceed 75% of the maximum power speed, as this may cause unnecessary malfunctions during riding. Gear usage: Taking a common 125CC motorcycle as an example. First gear is only used for low-speed starts or climbing very steep slopes. Immediately after starting, shift into second gear. Second gear is generally suitable for speeds between 10-20, third gear is suitable for speeds between 20-40, fourth gear is suitable for speeds between 30-50, and speeds above 40 can generally be driven in fifth gear.

7

1

Share

What is the difference between iron and aluminum engine blocks?

The differences between iron and aluminum engine blocks are as follows: 1. Cast iron cylinder: It has better wear resistance and durability compared to aluminum cylinders, and its manufacturing cost is relatively lower. However, its disadvantage is that the expansion coefficient differs from that of the aluminum pistons inside. When driving at high speeds for extended periods, causing the engine to overheat, the aluminum pistons expand more than the cast iron cylinder, which can sometimes lead to piston seizure, rendering the vehicle undrivable. Additionally, its heavier weight increases fuel consumption. 2. Aluminum cylinder: It is lighter in weight, and its expansion coefficient matches that of the pistons, almost eliminating the risk of piston seizure. It also has better heat dissipation than cast iron. Although its wear resistance is slightly lower than that of cast iron, the difference is minimal due to the use of aluminum alloy. While the material cost is higher than cast iron, the impact on the overall engine cost is negligible. Moreover, its lighter weight contributes to better fuel efficiency.

1

Share

What to Do When Driving License Points Reach Zero?

If a driving license accumulates zero points within one cycle, the holder must attend a seven-day training program at the local traffic management department of the public security authority. After completing the training, the driver must retake the subject one exam. Below are relevant details about driving license penalties: 1. Retaking the exam after failure: After accumulating 12 penalty points, drivers must undergo eight-hour daily training on road traffic safety regulations and related knowledge. The exam content is identical to that for new license applicants. Upon passing the subject one exam, the penalty points will be cleared, and the traffic authority will return the driving license. Those who fail must retake the training and exam. 2. Standardized driving: If a license accumulates 12 points for two consecutive cycles or 24 points in one cycle, the driver must retake both subject one and subject three exams. Traffic regulations are strictly enforced - any traffic violation by motor vehicle drivers will be penalized, with severe cases potentially resulting in license revocation. Therefore, standardized driving is essential.

12

0

Share

Why does the windshield washer fluid not go down?

There are two possible reasons: first, there may be a lack of windshield washer fluid; second, the nozzle might be clogged. It is recommended to first check the windshield washer fluid reservoir. The functions of automotive windshield washer fluid include the following four points: 1. Cleaning performance: Windshield washer fluid is composed of various surfactants and additives. Surfactants usually have functions such as wetting, penetrating, and solubilizing, thus achieving the effect of cleaning and removing dirt; 2. Antifreeze performance: It can significantly reduce the freezing point of the liquid, thereby achieving an antifreeze effect and quickly dissolving frost; 3. Anti-fog performance: A single-molecule protective layer is formed on the glass surface, which can prevent the formation of fog droplets, ensuring the windshield is clear and transparent with a clear view; 4. Anti-static performance: After cleaning with windshield washer fluid, substances adsorbed on the glass surface can eliminate the charge on the glass surface, providing anti-static performance.

11

1

Share

What Causes Vibration When Idling in D Gear?

The following are the reasons for vibration when idling in D gear: 1. High engine speed: When the engine speed is too high during cold start, the torque converter transmits more power, resulting in greater impact and more noticeable vibration when shifting gears. 2. Brake not fully engaged: When shifting gears, the engine's power is directly transmitted to the wheels. If the brake is not fully engaged, the wheels may move slightly, causing the vehicle to jerk forward with a strong vibration sensation. 3. Brake released too early: When the traffic light turns green, shifting into drive and releasing the brake to start can cause the vehicle to lurch forward violently if the brake is released too soon, leading to a sudden power combination. Since the automatic transmission gear lever does not directly control the gear position but acts as a signal device, different signals are sent to the transmission control system when different gears are engaged, and the transmission control system then completes the gear shift.

14

5

Share

Where is the ABS pump located in a BMW 7 Series?

How to Tell When the Steering Wheel is Centered?

Can motorcycles go on highways in Hainan?

What is the difference between iron and aluminum engine blocks?

What to Do When Driving License Points Reach Zero?

Why does the windshield washer fluid not go down?

What Causes Vibration When Idling in D Gear?

How to Use Cruise Control in Volkswagen Teramont?

Can Hill Start Assist Be Installed Aftermarket?

What are the battery issues with the 535le new energy vehicle?

Used Car Ownership Transfer and License Plate Replacement Process?