Where is the 4008's cabin air filter located?

2 Answers
DeIris
09/01/25 3:57am
4008's cabin air filter is located under the glove compartment on the passenger side. The functions of the cabin air filter are: 1. Provide fresh air for the cabin; 2. Ensure safety and hygiene inside the vehicle; 3. Absorb harmful substances; 4. Filter solid particles from the air. Taking the 2019 4008 as an example, it belongs to the compact SUV category, with body dimensions of: length 4510mm, width 1850mm, height 1628mm, wheelbase 2730mm, and fuel tank capacity of 53 liters. The 2019 4008 features a MacPherson strut front suspension and a torsion beam rear suspension. It is equipped with a 1.6L turbocharged engine, delivering a maximum horsepower of 170PS, maximum power of 125kW, and maximum torque of 250Nm, paired with a 6-speed automatic transmission.
Was this review help?
9
2
Share
AlexandraAnn
09/13/25 6:46am
I remember the cabin air filter of the Peugeot 4008 is usually hidden behind the glove compartment on the passenger side. Just open the glove box, and there it is – a simple release of the clips allows you to take it out. Maintaining this filter is quite important because when it gets dirty, the air quality inside the car deteriorates significantly, easily causing coughing or allergies, especially when using the AC in summer. It's recommended to replace it every 12 months or after driving 15,000 kilometers. Don’t skimp when buying a filter; opt for ones with pollen protection or carbon adsorption to filter out dust and odors. DIY replacement is easy too – just search for tutorials online, and it can be done in minutes, making your drive more comfortable and fuel-efficient.
Was this review help?
12
2
Share
Expand All
More Forum Discussions

How to Replace the Battery of a Tire Pressure Monitor?

It is necessary to remove the tire and then install the sensor on the wheel hub. After installation, vehicle dynamic balancing must be performed, which is generally done at a tire shop or repair shop. For external tire pressure monitors, simply replace the sensor on the tire's valve stem. The steps are simple and can be done by yourself.
11
4
Share

How to Modify Xenon Lights?

This modification method mainly uses original matching xenon headlights, which combine xenon light sources with specially designed light distribution lenses and reflectors. Choose a reasonable installation position to meet personalized needs.
7
5
Share

How to Register After Installing a Roof Rack on Your Car?

If you install a roof rack that can be easily removed, you can avoid the hassle of going through the procedures. Simply remove and restore it during the annual inspection, and reinstall it after the inspection is completed. The owner can directly go to the vehicle management office to apply for the change registration within 10 days after the modification.
15
4
Share

How to Turn Off the Trunk Light That Stays On When the Car Trunk Is Open?

First, check if the trunk is fully closed. If not, you can simply close the trunk again to resolve the issue. If the light remains on after the trunk is closed, it might be due to a faulty sensor switch. It is recommended to visit a professional repair shop for maintenance.
8
5
Share

How to Remove Car Interior Door Panel?

Use a flat-head screwdriver to pry open the lower trim panel of the door handle, starting from the middle and moving downward, then outward to pry open the front section of the rear door. After removing the lower trim panel of the handle, you will see two black 8mm hex bolts inside. Use a socket wrench to unscrew them. Unplug the power window switch connector. Use a flat-head screwdriver to pry open the decorative panel of the door handle from front to back. Remember to pull the door handle while removing it. Use your hands to slightly pry open a gap at the bottom of the interior door panel, then insert a pry tool to loosen and remove the panel one clip at a time.
17
0
Share

How to Check Tire Pressure on Nissan Tiida?

First, unscrew the valve cap of the tire. Note that you should twist it quickly when opening. Insert the measuring head of the tire pressure gauge onto the valve stem, ensuring even pressure when pressing it onto the valve. Compare the measured data from the tire pressure gauge with the manufacturer's specifications to see if it meets the standard. If the pressure is insufficient, inflate the tire promptly.
10
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.