Where is Mitsubishi Motors produced?

What Causes Car Brake Pulling?

The reasons for car brake pulling are: 1. Uneven braking force on the left and right sides of the same axle; 2. Different braking torque on the left and right sides of the same axle; 3. Differences in tire pressure, tread patterns, or wear levels between the two sides; 4. Incorrect wheel alignment; 5. Deformation of the front shock absorber springs; 6. Failure of the front shock absorbers; 7. Excessive chassis wear; 8. Overall deformation of the vehicle frame. Solutions for car brake pulling include: 1. Properly adjusting the brake clearance on both sides or resurfacing the contact surface of the brake shoes; 2. Avoiding driving over curbs and slowing down when encountering large potholes; 3. Rotating tire positions every 20,000 kilometers; 4. Using a specialized shock absorber tester to measure the absorption rate and assess the condition of the shock absorbers.

2

1

Share

What is the difference between longitudinal and transverse engines?

The differences between longitudinal and transverse engines are as follows: 1. The placement direction of the engine and transmission is different. A transverse engine is placed horizontally, requiring the transmission to also be placed horizontally side by side. A longitudinal engine is placed vertically, with the transmission positioned behind the engine. 2. The power output direction is different. The power transmission direction of a transverse engine is usually perpendicular to the direction of the car's movement, while the power transmission direction of a longitudinal engine is parallel to the car's movement direction. 3. The car's drive system is different. Transverse engines are typically front-engine, front-wheel drive, while longitudinal engines are usually front-engine, rear-wheel drive. 4. The suspension systems differ. Models with a longitudinal engine layout often feature more advanced multi-link or double-wishbone shock absorbers for the front suspension. Models with a transverse engine layout mostly use MacPherson struts for the front suspension.

4

1

Share

Should the Clutch Be Released Slowly When Shifting to Second Gear?

There are two scenarios regarding whether the clutch should be released slowly when shifting to second gear, as detailed below: 1. Shifting from a lower gear to a higher gear: In this case, there is no need to release the clutch slowly. However, it is important to remember that the shift should only occur when the vehicle speed reaches the appropriate shifting speed. At this point, releasing the clutch quickly or slowly during upshifting will not significantly affect the vehicle, as the speed has already increased and the car won't stall. Therefore, in this scenario, whether the clutch is released quickly or slowly has minimal impact on the shifting process, and the transition will be relatively smooth. 2. Shifting from a higher gear to a lower gear: In this situation, the clutch should be released slowly. Downshifting requires the speed to decrease, and releasing the clutch too quickly can cause a noticeable jerk. Hence, after shifting, it is advisable to release the clutch slowly to allow the car a transition period. Additionally, if the vehicle speed is relatively high when downshifting, it is best to lightly apply the brakes to reduce the speed first, which is also beneficial for the transmission.

2

1

Share

What are the reasons for the failure of the automatic parking function?

The reasons for the failure of the automatic parking function: The parking brake lever cannot be fixed; the parking brake fails; the parking brake makes abnormal noises or is aging; the gap between the friction plate of the automatic parking system and the brake drum is too large, the friction plate and the brake drum are contaminated with oil or severely worn, the rivets are exposed, and the surface is hardened, causing slippage and failure; the parking brake shaft is severely worn, the gap is too large, and the parking brake lever is adjusted too long. Additional information: 1. Automatic parking function: The automatic parking function is a feature that allows the driver to avoid unnecessary vehicle sliding without the need for prolonged braking or activating the electronic parking brake. 2. Principle: The automatic parking function provides precise parking force through a slope sensor controlled by the controller. When starting the vehicle, the parking control unit calculates information provided by the clutch distance sensor, clutch engagement speed sensor, and throttle pedal sensor. When the driving force exceeds the running resistance, the parking brake is automatically released, enabling the car to start smoothly.

6

2

Share

What Are the Environmental Hazards of Automobile Exhaust?

Automobile exhaust poses environmental hazards including the greenhouse effect, photochemical smog, and impacts on plant growth. Greenhouse Effect: Automobile pollution has become a global nuisance, and its 'contribution' to the increase in greenhouse gas concentrations cannot be ignored. The internal combustion engine of a car is essentially a mini chemical plant, consuming vast amounts of petroleum resources. Gasoline combustion generates driving force but also produces many complex chemical reactions, emitting large quantities of greenhouse gases that exacerbate the greenhouse effect. Photochemical Smog: Under certain conditions, these pollutants can form secondary pollution—photochemical smog, which poses even greater harm to human health. Photochemical smog is a complex type of smog generated when hydrocarbons and nitrogen oxides from vehicle exhaust react under specific temperature conditions, such as calm winds, low humidity, high temperatures, and prolonged sunlight exposure. Impact on Plant Growth: Automobile exhaust can also affect plant growth, especially when the concentration of exhaust reaches a certain level, leading to the acidification of soil and water sources, which naturally impacts the growth of certain plants.

5

3

Share

Does Coasting in Neutral Save or Waste Fuel?

Not necessarily fuel-saving, and may even waste fuel. Many modern vehicles are equipped with electronically controlled fuel injection systems. When the car is shifted into neutral, the ECU defaults to assuming the car is idling, thereby increasing fuel injection to maintain idle speed. The electronic fuel injection control system inherently has fuel reduction or cutoff functions. Shifting to neutral in such scenarios not only disables these functions but also increases fuel injection. Fuel-saving tips: 1. Smooth Driving: One of the most practical and effective fuel-saving methods is maintaining steady driving. For small-displacement vehicles, it's best to keep speeds between 60 to 80 km/h, while for larger-displacement vehicles, maintain speeds between 80 to 100 km/h. 2. Avoid Congested Routes: Before driving, check the route. If it's congested, it's best to detour. In traffic jams, the car not only can't move but also remains in an operating state, which wastes fuel. 3. Reduce Vehicle Weight: The weight of the car also increases fuel consumption. Therefore, if some items in the car are temporarily not needed, try to remove them to reduce the vehicle's weight.

19

3

Share

Where is Mitsubishi Motors produced?

What Causes Car Brake Pulling?

What is the difference between longitudinal and transverse engines?

Should the Clutch Be Released Slowly When Shifting to Second Gear?

What are the reasons for the failure of the automatic parking function?

What Are the Environmental Hazards of Automobile Exhaust?

Does Coasting in Neutral Save or Waste Fuel?

Why is the sound of closing the left and right car doors different?

How Many Kilograms is One Liter of Gasoline?

What Causes the Clicking Sound When Starting a Car?

What Causes the Car to Shake When Releasing the Clutch in Second Gear?