Where is Lynk & Co manufactured?

1 Answers
DelKendra
07/29/25 3:46pm
Lynk & Co is manufactured by Geely Auto. The models under the Lynk & Co brand include: Lynk & Co 03, Lynk & Co 01, Lynk & Co 02, Lynk & Co 01 New Energy, Lynk & Co 05, etc. Taking the 2021 Lynk & Co 03 as an example, it belongs to the compact car category with body dimensions of: length 4639mm, width 1840mm, height 1472mm, and a wheelbase of 2730mm. The curb weight is 1395kg. The 2021 Lynk & Co 03 features a MacPherson strut front suspension and a multi-link independent rear suspension. It is equipped with a 1.5T turbocharged engine, delivering a maximum horsepower of 156PS, a maximum power of 115kW, and a maximum torque of 245Nm, paired with a 6-speed manual transmission.
Was this review help?
2
4
Share
More Forum Discussions

What Are the Causes of Motorcycle Carburetor Fuel Leakage?

Motorcycle carburetor fuel leakage is caused by: 1. The main fuel needle being stuck, leading to continuously rising fuel level; 2. Wear of the needle valve resulting in incomplete closure; 3. The float being stuck and unable to close the needle valve; 4. Float damage or immersion in gasoline causing loss of buoyancy. The carburetor is a mechanical device that mixes a certain proportion of gasoline with air under the vacuum created by the engine operation. Motorcycles are two-wheeled or three-wheeled vehicles driven by gasoline engines, steered by handlebars for front-wheel turning. They are lightweight, flexible, fast-moving, widely used for patrol, passenger and cargo transportation, and also serve as sports equipment. Broadly speaking, motorcycles are categorized into street bikes, road racing motorcycles, off-road motorcycles, cruisers, and touring bikes.
5
2
Share

What is the top speed of an electric car?

The top speed of an electric car can reach up to 323 km/h. Taking the Tesla Model 3 as an example, here are the specific details of the Model 3: 1. Vehicle Positioning: The Model 3 is a mid-sized electric car with a wheelbase of 2875 mm, and its length, width, and height are 4694 mm, 1850 mm, and 1443 mm respectively. 2. Power: The Model 3 is available in both rear-wheel drive and all-wheel drive versions. The all-wheel drive version is a dual-motor model, while the rear-wheel drive version is a single-motor model. The total power of the all-wheel drive Model 3 is 340 kW, with a total torque of 639 Nm. The rear-wheel drive version has a maximum motor power of 202 kW and a maximum torque of 404 Nm. 3. Battery: The Model 3 uses ternary lithium batteries across all models, which have higher energy density and are lighter in weight.
9
5
Share

What are the length, width, and height of the Lavida?

The length, width, and height of the Lavida are 4605mm, 1765mm, and 1460mm respectively, with a wheelbase of 2610mm. The Lavida (LAVIDA) is an independently developed A-segment car by Shanghai Volkswagen, belonging to the sedan category. It features a MacPherson strut front suspension and a torsion beam rear suspension, with a front-engine, front-wheel-drive layout. In terms of power, the Volkswagen Lavida is equipped with a 1.6L inline-four-cylinder multi-point fuel injection engine, delivering a maximum power of 77 kW and a maximum torque of 155 Nm. It is paired with either a 5-speed manual transmission or a 7-speed dual-clutch transmission.
18
3
Share

What Causes Smoke from the Engine Hood?

Smoke from the engine hood can occur under the following circumstances: 1. Small fuel injection advance angle: This leads to incomplete combustion; slight leakage in the cylinder liner or water in the fuel can also cause it. White smoke during cold starts, especially in low temperatures, is normal and should disappear as the engine warms up. 2. Air-fuel ratio imbalance: Decreased cylinder pressure; early fuel injection (excessive fuel injection advance angle) can cause black smoke; failure of the smoke limiter on the fuel injection pump can also result in black smoke during rapid acceleration; malfunctioning exhaust brake system. 3. Burning engine oil: Blue smoke from the car engine is often due to "burning engine oil." In such cases, check for wear in the engine cylinder liner, "stuck rings," ring alignment, aging or deformation of valve seals, excessive valve guide clearance, etc. This condition is usually accompanied by blow-by in the crankcase.
13
1
Share

How often should the activated carbon canister be replaced?

The activated carbon canister generally needs to be replaced every 4 years or 60,000 kilometers. The carbon canister is prone to clogging, which can prevent fuel vapors from escaping, leading to excessive pressure from exhaust gases in the fuel tank. Its primary function is to reduce emission pollution. During daily use, it's important to note that the activated carbon canister should not be subjected to impacts or strong vibrations, as these can shorten its lifespan. The activated carbon canister is a container filled with activated carbon, designed to adsorb gasoline vapors escaping from the fuel tank and carburetor when the engine is turned off. When the engine is started, the adsorbed gasoline is then blown out and burned. The activated carbon canister is a crucial component in both the ignition and emission systems.
14
1
Share

Can Modified Mid-to-Rear Exhaust Pass Annual Inspection?

Without approval from the traffic management department, modified mid-to-rear exhaust systems cannot pass annual inspection. Below is a detailed introduction to the types of car modifications: 1. Exterior Modifications: The most common exterior modifications involve installing aerodynamic kits. These kits include components such as the intake grille, side skirts, rear diffusers, and spoilers. Other exterior modifications include roof racks, sunroofs, parking distance sensors, decorative lighting, specified lighting fixtures, and side mirrors. 2. Comfort Modifications: The goal of comfort modifications is to provide the driver with a more comfortable environment and improved stability. Examples include upgrading the suspension system, interior equipment, soundproofing, window tinting, installing wider wheels, and upgrading headlights. 3. Performance Modifications: A car's power comes from the combustion of an air-fuel mixture ignited by high-voltage sparks, which pushes the pistons. Therefore, enhancing a car's performance requires upgrading various systems to increase the combustion efficiency within the cylinders.
12
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.