Where is Great Wall Lubricant produced?

Is the Verna engine domestically produced?

The Verna engine is domestically produced, with the G4FA model engine manufactured at the engine plant located in Shunyi, Beijing. Below are relevant details: 1. As an advanced model in Beijing Hyundai's small car segment, the Verna is positioned higher than the Accent. This is primarily reflected in its overall configuration and mechanical capabilities, which rival those of its German competitors. 2. The Hyundai Verna utilizes an inline engine, which is the most widely used cylinder arrangement today, especially for engines with displacements below 2.5L. In this layout, all cylinders are aligned at the same angle in a single plane and share one cylinder head. Additionally, the engine block and crankshaft structure are relatively simple, resembling a single file of cylinders standing in a straight line. 3. For the steering system, the Verna comes standard with MDPS electric power steering across all variants, featuring an added steering angle sensor to enhance ECU processing speed for more responsive feedback. It employs a permanent magnet AC synchronous motor with faster dynamic response, ensuring smooth and safe operation while effectively reducing vibration and noise. The gear-to-rack rotation amplitude is increased for more direct steering response.

9

4

Share

Where is the fuel tank switch of the Buick Verano?

The fuel tank switch is located on the fuel tank cover. When the door lock is unlocked, simply press the fuel tank cover to open it. Below is some relevant information about the Buick Verano: 1. The manufacturer of the Buick Verano is SAIC General Motors Buick. The body structure is a 4-door, 5-seater sedan. 2. Body dimensions: The length, width, and height are 4723mm, 1802mm, and 1466mm respectively. The wheelbase is 2830mm. 3. Powertrain: Equipped with a 1.0T 125 horsepower engine, paired with a 6-speed automatic transmission and a CVT continuously variable transmission. 4. Chassis: The drive system is front-wheel drive, with a front suspension of MacPherson independent suspension and a rear suspension of torsion beam and Watt's linkage non-independent suspension.

18

3

Share

Where is the rear tow hook located on the Geely Emgrand?

The tow hook and other vehicle tools are stored under the trunk cover of the Emgrand. The front tow hook installation position is located behind a small cover on the lower left side of the front fascia. Simply press the left side of the cover to open it and reveal the installation point. The rear tow hook is already fixed to the rear chassis. The tow hook, also known as a tow ball, is a towing device connected to the vehicle's rear crash beam. It is mainly installed on ordinary household vehicles and self-propelled RVs. The purpose of the tow hook is to tow small trailers or towable RVs. It can also be used with rear-mounted bicycle racks or luggage carriers, increasing the vehicle's cargo space. How to use the tow hook: Locate the tow hook positions at the rear of the towing vehicle and the front of the towed vehicle. The tow hook is designed under the bumper, and you can find a hidden space by inspecting the front and rear bumpers. This space is usually covered by a round or square cover, indicating the tow hook location. When installing the towing equipment, whether using soft or hard towing tools, ensure the connection to the vehicle hook is secure. If the tow hook has a safety lock, make sure it is properly engaged. Precautions for using the tow hook: Take wide turns when towing. Since the towed vehicle extends the body length and increases the turning radius, making wider turns helps avoid accidents involving pedestrians or non-motorized vehicles. Pay attention to the tire pressure of small trailers. When passing over speed bumps, if the trailer's tire pressure remains at the normal 2.5 bar, it may bounce and cause the trailer to detach from the tow hook, which is very dangerous. Many small trailers use rubber torsion axles for suspension, resulting in poor shock absorption. It is recommended to reduce the tire pressure of small trailers to around 1.3 bar to allow the tires to act as shock absorbers. When reversing, it is advisable to first detach the trailer or RV from the tow hook. Towing while reversing can cause the trailer or RV to swing unpredictably, making it difficult to park properly. Additionally, when reversing a vehicle with a tow hook into a parking space, leave extra space if there are obstacles or other vehicles behind, as the tow hook may collide with them. Similarly, be mindful of the rear situation when parallel parking.

19

3

Share

What Causes Car Shaking at Idle?

There are several reasons why a car may shake at idle: 1. Normal vibration. When the air conditioner is turned on while the car is stationary in summer, the compressor's start and stop moments can cause idle speed fluctuations. This happens because the engine control unit automatically increases idle speed when the compressor is running and returns to normal when the compressor stops, resulting in noticeable vibration during idle speed transitions. This is a normal phenomenon. 2. Idle shaking caused by insufficient battery voltage. If the idle speed shakes when the headlights are turned on while the car is stationary, or if the window switch isn't released promptly after the window is fully raised, it may indicate insufficient battery charge. 3. Shaking caused by engine electronic control system faults. (1) Idle speed control valve issues. This fault typically occurs only in vehicles with cable-operated throttles, mostly older cars manufactured before 2010. This type of throttle regulates air intake through an idle speed control valve, which converts rotational motion into linear motion via a ball screw mechanism. If the ball screw mechanism malfunctions, it can cause operational deviations, leading to idle speed shaking. (2) Abnormal oxygen sensor signals. The oxygen sensor monitors oxygen levels in exhaust gases, and its signal is a crucial parameter for the engine to precisely adjust the air-fuel ratio. Abnormal oxygen sensor signals may cause irregular idle speeds. (3) Abnormal throttle idle switch signals. Poor contact in the idle switch can lead to unstable idle signals, resulting in idle speed fluctuations.

20

0

Share

What are the dimensions of the Nissan Sylphy?

The wheelbase of the Nissan Sylphy is: 2700mm, and the body length, width, and height come in two dimensions (mm), which are: 4631*1760*1503; and 4665*1700*1505. Here are some related details: 1. The front face of the Sylphy features more curved surfaces, with a U-shaped chrome trim and boomerang-style headlights on both sides, which are part of Nissan's latest design language. 2. In terms of body dimensions, the new Nissan Sylphy has a wheelbase of 2700mm, a body length of 4665mm, a width of 1700mm, and a height of 1505mm. Space is one of the highlights of the Sylphy, with ample room for normal seating and generous space for both passengers and storage. 3. For safety features, in addition to the more widespread ESC body stability system, higher-end models also include tire pressure monitoring. Furthermore, high-tech driving assistance functions such as lane departure warning and lane change assist are also available. The newly added 2019 Intelligent Edition is equipped with the "Intelligent Driving+" connectivity system independently developed by Dongfeng Nissan, which includes features like intelligent voice control, full-time in-car navigation, remote real-time monitoring, 24-hour entertainment, in-car Wi-Fi hotspot, and worry-free data usage. 4. The Sylphy is equipped with a classic combination of a 1.6L naturally aspirated engine and a CVT continuously variable transmission, delivering a maximum power of 91kW (124PS)/5600rpm and a maximum torque of 153N•m/4400rpm.

7

0

Share

How to Activate the Tire Pressure Monitoring in the Bora?

The tire pressure monitoring system in the Bora is located inside the tires, which contain sensors. The monitoring button is positioned on the multifunction steering wheel. The Volkswagen Bora is equipped with a tire pressure warning system. When the pressure in one or more tires is significantly lower than the set pressure or if there is a structural issue with the tire, the system emits a warning sound, and the instrument cluster display may show a corresponding text message. However, specific tire pressure values are not displayed. Additional information about the tire pressure monitoring system is as follows: 1. The tire pressure monitoring system automatically and continuously monitors the tire pressure while the vehicle is in motion, alerting the driver to leaks or low pressure. It is an active safety device that warns the driver of potential tire hazards, prompting them to take appropriate action. 2. There are two main types of tire pressure monitoring systems: indirect and direct.

1

Share

Where is Great Wall Lubricant produced?

Is the Verna engine domestically produced?

Where is the fuel tank switch of the Buick Verano?

Where is the rear tow hook located on the Geely Emgrand?

What Causes Car Shaking at Idle?

What are the dimensions of the Nissan Sylphy?

How to Activate the Tire Pressure Monitoring in the Bora?

Will Randomly Tapping the Brake in Subject Three Lead to Deduction?

What is the principle of an automobile throttle?

What are the installation steps for the ETC device?

What Causes False High Engine Coolant Temperature?