Where does the Xuguang Expressway run from and to?

2 Answers
PaisleyLynn
07/28/25 6:58pm
Xuguang Expressway runs from Xuchang City in Henan Province to Guangzhou City in Guangdong Province. Also known as the Xuguang Expressway, it is designated as G0421 (formerly G4W2) in the national expressway network and serves as one of the western parallel routes to the Beijing-Hong Kong-Macao Expressway (National Expressway G4), a radial trunk line in the national expressway network. The Xuguang Expressway spans approximately 1,130 kilometers, running from north to south and passing through four provinces: Henan, Hubei, Hunan, and Guangdong. It is primarily composed of the Lannan Expressway (Xuchang to Yexian section), the Lintong Expressway (formerly Jiaotong Expressway, Yexian to Tongbai County section), the Suiyue Expressway, the Yuelin Expressway, the Qinglian Expressway, and the Guangqing Expressway.
Was this review help?
10
3
Share
JasmineMarie
08/12/25 12:18am
The Xuguang Expressway stretches from Xuchang City in Henan Province all the way to Guangzhou City in Guangdong Province. It's quite a long expressway, roughly about 2,000 kilometers. As a seasoned long-haul driver, I'm very familiar with this route: it connects several provinces including Henan, Hubei, Hunan, and Guangdong, making north-south travel extremely convenient. However, when driving long distances, it's crucial to pay attention to vehicle maintenance—like checking tire wear and the brake system. Highways can easily lead to overloading, so don't skimp on these small expenses at the cost of safety. Also, if the engine overheats, you might end up stranded halfway. I make it a habit to take breaks at service areas to check the oil and coolant levels, ensuring a smooth and uninterrupted journey. This route has heavy traffic, and the road surface isn't always even, so maintaining a steady speed is more important than anything else.
Was this review help?
16
2
Share
Expand All
More Forum Discussions

What are the reasons for the power loss issue in BMW X6?

Reasons for the power loss issue in BMW X6: Contamination inside the transmission: When an automatic transmission experiences jerking, in many cases, it is not due to damage to the internal valve body but rather the presence of stubborn dirt and impurities inside. Especially when these contaminants accumulate inside the valve body, they can form blockages, preventing effective regulation of oil pressure and leading to issues like jerking, impact, and slipping. Transmission overheating: The problem of transmission overheating should not be overlooked. High temperatures can degrade the quality and friction characteristics of automatic transmission fluid, increasing friction and wear. This results in transmission noise, and sludge (impurities or dirt) can also form inside the transmission (e.g., in the valve body), causing jerking and impact.
20
0
Share

What is the reason for the BMW X3 welcome light not working?

The reason why the BMW X3 welcome light is not working: it is due to a fault in the control unit, and replacing the controller can solve the problem. Function of the welcome light: Its function is to enhance the aesthetic appeal, making the car look more noble and elegant. It can also be used to alert pedestrians and vehicles on the road, helping to avoid unnecessary accidents. Location of the welcome light: The door welcome light switch is usually located on the ceiling, along with the reading light and sunroof switches. Once activated, the welcome light can automatically sense and turn on or off by itself. Precautions: It is important to choose welcome lights from reputable brands, as these products are guaranteed in quality and have a more comprehensive after-sales service system.
4
4
Share

What does it mean when an Alto car displays a car with a lock?

When an Alto car displays a car with a lock, it indicates that the car's anti-theft lock is engaged. Categories: Based on technical principles, car anti-theft locks can be broadly classified into mechanical anti-theft locks, electronic anti-theft alarm locks, and networked anti-theft (positioning, tracking) systems. Car anti-theft locks include electronic car anti-theft locks, network car anti-theft locks, fuel line locks, clutch and brake anti-theft locks, wheel anti-theft locks, gear shift locks, steering wheel locks, and car anti-theft magnetic plates. Principle: When the ignition switch is turned on, the key transponder and the anti-theft controller exchange initial information. If the identification codes between the key and the chip do not match, the anti-theft controller will not continue to communicate with the ECU, keeping the ignition system and fuel injection system circuits in an open state, preventing the engine from starting.
18
1
Share

How to Break in a New Car for Better Fuel Efficiency?

The methods for breaking in a new car to save fuel are: 1. Warm up the engine before starting; 2. Avoid sudden braking; 3. Prevent overloading; 4. Avoid long-distance trips; 5. Do not drive at high speeds; 6. Use high-quality gasoline; 7. Do not remove the speed limiter prematurely; 8. Shift gears in a timely manner; 9. Properly adjust the ignition and fuel systems. The proper usage during the break-in period includes: 1. Preheat the engine when cold—proper warming allows the oil to lubricate the engine effectively, reducing wear; 2. Shift gears promptly while driving, especially for manual transmission cars—reasonable gear changes during the break-in period help avoid high-gear low-RPM or low-gear high-RPM situations; 3. Ensure timely maintenance during the break-in period.
13
4
Share

Why is the exterior door of the new Jetta difficult to open?

Reasons why the exterior door of the new Jetta is difficult to open: Central locking system engaged: The central locking system automatically activates when the vehicle speed exceeds 15km/h. Its purpose is to prevent passengers from accidentally opening doors while the vehicle is in motion, thereby avoiding potential accidents. Child safety lock: If the rear door cannot be opened when the central locking system is disengaged, it indicates that the child safety lock is engaged. Door lock malfunction: Possible issues with the remote control or RF transmitter, or problems with the main unit or door control module. Check if the remote control has power. If the battery is not the issue, test whether other buttons on the remote control function properly. If other buttons work, the problem lies with the door control module.
8
5
Share

What is the reason for the anti-skid light on the Volkswagen Sagitar indicating a sensor failure?

The reason for the anti-skid light on the Volkswagen Sagitar indicating a sensor failure is related to severe engine carbon deposits. It is recommended to go to a 4S shop to clean the internal carbon deposits in the engine, clean the fuel injectors, clean the dirty intake manifold, and remove the carbon layer on the exhaust valve. The car's anti-skid system: The car's anti-skid system is another set of anti-skid control systems following ABS, and it is a further development and supplement to the ABS system. The main purpose of the anti-skid system: The main purpose of the anti-skid system is to prevent the driving wheels from slipping when the vehicle starts and accelerates, effectively maintaining the stability of the car's driving direction. It controls the sliding within a certain range, thereby preventing the sliding wheels from rapidly losing direction.
7
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.