Where can the vehicle production date be accurately viewed?

What are the symptoms of a torque converter failure?

The symptoms of a torque converter failure are as follows: 1. No working fluid in the torque converter: Since there is no mechanical connection between the pump impeller and the turbine in the torque converter, power is transmitted through the fluid as a medium. Without fluid, power naturally cannot be transmitted. 2. Loose or stuck connection between the turbine and the turbine shaft: Cracks at the welding point between the turbine blades and the turbine spline hub, damage to the spline connection between the spline hub and the turbine shaft, or bearing failure inside the torque converter can cause the turbine to become loose or stuck to the turbine shaft, preventing power from being output through the turbine. 3. White smoke: The engine operates normally, but fuel consumption increases. The transmission and transmission oil temperature rise significantly, and the transmission oil is prone to deterioration. In severe cases, white smoke may emerge from the oil filler port.

17

4

Share

What's the reason for a diesel engine not being able to restart after stalling?

Main reason is that the engine temperature is too low. As long as the engine is kept warm and the biting cold wind is prevented from blowing directly into the engine compartment, the failure to start can be avoided. Specific information is as follows: 1. Parking precautions: When parking in winter, pay attention to the direction of the front of the car. It is best to point the front of the car towards a building, using the building to block the wind and prevent the engine from becoming too cold due to the cold wind. When parking at night, you can point the front of the car towards the direction of the rising sun, so that the first rays of sunlight in the morning can shine on the front of the car, helping the engine to warm up. This makes starting the car much easier. 2. Extended information: If the engine stalls when shifting gears, it may be due to the idle speed being too low at the time, or the idle cut-off valve not being tightened properly, or it could be caused by shifting into too high a gear, or the oil-gas separator being severely clogged.

3

5

Share

Does a Dead Car Battery Need Replacement?

1. Jumper Cables: These are essential items for jump-starting a car. Never attempt to use random wires as a substitute, because the instantaneous current during vehicle startup can reach 200-600A, and even up to 1000A for diesel vehicles. Calculated, a 10-square-millimeter copper wire is required to ensure smooth and safe startup. Therefore, always purchase branded, high-quality car battery jumper cables—don't compromise on safety to save money. This is one of the must-have items in your car; it can be used when your battery dies or to help others in need. 2. Emergency Power Source: This is a new portable device similar to a power bank, available in lead-acid and polymer lithium-ion versions. It can assist in jump-starting a depleted battery and also functions as a multi-purpose tool for lighting, charging mobile phones, and inflating tires with an air pump. Typically compact and lightweight, having one eliminates the need to seek help for a jump-start. After use, always recharge it promptly to ensure sufficient power for emergencies. 3. Positive to Positive, Connect Positive First: First, turn off all electrical devices in the car and ensure the key is in the 'off' position. Open the hood and locate the battery, which is clearly marked with positive (+) and negative (-) terminals (usually red '+' for positive). Jumper cables typically come in pairs. Take out the red cable first, open the battery cover, and firmly clamp one end to the dead battery's positive terminal. Then, attach the other end to the positive terminal of the rescue vehicle's battery. Always connect the positive terminal first, followed by the negative. Never reverse this order or let the clamps touch anything other than the battery terminals. 4. Negative to Negative, Connect Negative Last: After securing the red positive cable, take out the other jumper cable. First, clamp it firmly to the dead battery's negative terminal (usually marked with a black '-'). Then, while ensuring the clamp doesn't touch anything else, attach the other end to the rescue vehicle's negative terminal. Don't be alarmed if sparks appear during this step—it confirms the connection is correct. The reason for connecting the negative last is that most conductive metal parts of the car are grounded (i.e., connected to the negative). If the negative is connected first, accidentally touching any conductive part of the car body while attaching the positive clamp could cause a short circuit, damaging vehicle components. 5. After Starting the Vehicle, Remove Negative First, Then Positive: Once the batteries are connected, start the rescue vehicle to charge the dead battery. Then, the driver of the dead vehicle should turn the key to power the dashboard lights and attempt to start the engine (for no more than 5 seconds). If unsuccessful, gently press the rescue vehicle's accelerator to maintain around 2500 RPM, then try starting again. If the starter and fuel supply are functional, the car should start. After the dead vehicle is running, first remove the negative clamp, then the positive clamp—the same logic as in step 4 applies here. Never reverse the battery's positive and negative connections. For safety, strictly follow the order: connect positive first, then negative; remove negative first, then positive.

6

3

Share

What is a Vehicle Emergency Power Supply?

Function of emergency power supply vehicles: They can be used for emergency power supply at airports, communication facilities, telecommunications, coal mines, and oil fields, playing a crucial role in emergency repairs and power supply during unexpected incidents. An emergency power supply vehicle is a special vehicle equipped with a power supply device. It mainly consists of a vehicle chassis, diesel generator set, power transmission and distribution system, high-efficiency sound insulation and noise reduction box, intake and exhaust noise reduction system, exhaust muffler system, lighting system, hydraulic support system, cable winch, and tool equipment compartment. Main features of emergency power supply vehicles: Emergency power supply vehicles offer multiple types of voltage outputs, providing 48V, 110V, or 220V DC outputs, which can meet the emergency power needs of 110kV, 220kV, and 500kV power plants. They have large capacity and long working hours, with a capacity of at least 400Ah, ensuring the power supply duration meets the emergency power demands of power plant control systems during emergencies. Additionally, their continuous operation time is no less than 2 hours. They are capable of normal operation under various environmental conditions. In harsh temperature environments, they ensure the normal functioning of battery packs and elevator components inside the vehicle. Moreover, for severe weather conditions such as thunderstorms and strong winds, the operation panel is designed to be windproof and waterproof. The circuit power supply equipment is equipped with lightning protection modules, providing lightning protection characteristics for the output power, ensuring the safety of equipment and personnel during thunderstorms.

16

5

Share

What does Black Warrior mean?

The basic meaning is to modify the car to be all black. Here are some considerations regarding car modification: Car modifications are subject to restrictions: Modifications must be carried out in compliance with relevant regulations, otherwise the vehicle may fail the annual inspection. Some parts cannot be modified: The car model, engine model, and chassis number cannot be altered, and the body structure must not be damaged; changing the car color, replacing the engine, body, or chassis requires inspection of the vehicle, and for replacing the engine, body, or chassis, a motor vehicle safety technical inspection certificate must be submitted; installing windshields, radiators, toolboxes, spare tire racks, front and rear bumpers, or adding interior decorations requires registration of changes.

19

3

Share

What is the fuel consumption of a 1.5L engine idling with AC on for one hour?

1.5L engine idling with AC on for one hour will increase fuel consumption by about 20% compared to normal driving. Here are some methods to reduce fuel consumption: 1. Strengthen vehicle maintenance: Car adjustments and maintenance affect engine performance and driving resistance. Owners should regularly perform routine maintenance at auto repair shops, such as checking tire pressure, wheel alignment, adjusting brake pad and brake drum clearance, lubricating chassis points, timely oil changes, and filter inspections. 2. Avoid prolonged engine idling: Fuel consumption during parking idling is much higher than during normal driving. Therefore, it's best to turn off the engine when the vehicle is stationary for extended periods, such as waiting for someone.

14

1

Share

Where can the vehicle production date be accurately viewed?

What are the symptoms of a torque converter failure?

What's the reason for a diesel engine not being able to restart after stalling?

Does a Dead Car Battery Need Replacement?

What is a Vehicle Emergency Power Supply?

What does Black Warrior mean?

What is the fuel consumption of a 1.5L engine idling with AC on for one hour?

Why does the car suddenly lose power?

Why does the car alarm go off for no reason?

What to Do When the Battery Light Turns Red on the Dashboard?

Is Mobil 1 Silver 5w40 a Full Synthetic Engine Oil?