Where are Wingu Tires produced?

2 Answers
EzraLee
09/05/25 6:49am
Wingu Tires are produced in Shandong Province. Here are some tire maintenance tips: 1. Regularly check wheel alignment and balance: Especially when you notice excessive vehicle vibration, which may indicate poor wheel alignment or imbalance. It's recommended to perform a dynamic wheel balance test. 2. Regular inspections: Check your tires at least once a month. Inspect the tire pressure when the tires are cold, including the spare tire pressure. 3. Check tire tread patterns: When tire wear reaches the wear indicator mark, the tire must be replaced. Driving with tires worn beyond the indicator mark is dangerous on wet surfaces.
Was this review help?
7
5
Share
DelBrantley
09/17/25 7:08am
Speaking of the production location of Stable tires, I find this question quite interesting. As someone who has been driving for over 20 years, I'm fairly familiar with tire brands, but I haven't heard much about the Stable name—it might be a smaller or emerging brand. In the tire manufacturing industry, production facilities are scattered worldwide. Major brands like Michelin have factories in France and the US, Bridgestone's main bases are in Southeast Asia, and China has also become a major hub, ranking among the world's top tire producers. To check a specific brand, I usually look at the DOT code on the tire sidewall, which contains production location and date information. If official website details are unavailable, the safest approach is to buy from reputable stores—safety first! Production locations can affect quality and durability—Chinese tires offer good value, but some smaller factories may have looser quality control. It's advisable to opt for tires produced by major manufacturers to reduce blowout risks. Remember, tires are critical for driving safety. Always check the production date and wear when replacing them—don't just go for the cheapest option.
Was this review help?
4
2
Share
Expand All
More Forum Discussions

Is Engine Oil Leak Covered Under Warranty?

Engine oil seal leakage falls within the three-year warranty period. The reasons for Passat engine oil leakage are as follows: Aging and hardening of sealing rings: Over 90% of oil leakage issues are caused by rubber sealing rings losing a significant amount of plasticizers and softeners due to prolonged exposure to alternating cold and warm temperatures, leading to corrosion, aging, and hardening problems. Incomplete combustion: Small fuel injection advance angle, incomplete combustion, slight water leakage in cylinder liners, water content in fuel, white smoke emission during cold starts which disappears as engine temperature rises. Smoke limiter failure: Air-fuel ratio imbalance, decreased cylinder pressure, premature fuel injection timing, failure of smoke limiter on fuel injection pump, malfunctioning exhaust brake system, engine cylinder liner wear, piston ring sticking, misalignment, aging and deformation of valve sealing rings, excessive valve guide clearance.
19
5
Share

Replacement Cycle for Magotan Transmission Control Unit?

The replacement cycle for the Magotan transmission control unit is every 3 years. Transmission: The transmission is a mechanism used to change the speed and torque from the engine. It can fix or change the transmission ratio between the output shaft and the input shaft in steps, also known as the gearbox. The transmission consists of a transmission mechanism and a control mechanism, and some vehicles also have a power output mechanism. The transmission mechanism mostly uses ordinary gear transmission, while some use planetary gears. Replacement Cycle: Remove the positioning screws, washers, springs, steel balls, and reverse light switch. Remove the shift control device and positioning pins. Remove the drain plug, fill plug, and vehicle speed sensor. Remove the transmission hanger. Cross and remove the transmission housing bolts in three steps. Remove the sealing screws. Spread the retaining ring and place it on the countershaft bearing, then remove it with a retaining ring pliers. Finally, pull out the transmission housing and positioning pins.
2
5
Share

Why Does the Rear Wheel Make Abnormal Noise When the Motorcycle Carries Two People?

Abnormal noise from the rear wheel when the motorcycle carries two people may be caused by insufficient lubrication of the wheel hub bearings, unstable tire pressure, or aging of the shock absorber bushings. Pay attention to tire pressure: Pressure is the lifeblood of a tire. Both too high and too low pressure will shorten its service life. If the pressure is too low, the tire body deformation increases, cracks are prone to appear on the tire side, and flexing motion occurs, leading to excessive heat generation, promoting rubber aging, fatigue of the cord layer, and cord breakage. Low pressure also increases the tire's contact area, accelerating wear on the tire shoulder. Excessive pressure causes the tire cords to be overstretched and deformed, reducing the tire body's elasticity and increasing the load the vehicle bears while driving. Regularly check front wheel alignment: Front wheel alignment significantly affects tire lifespan, with toe-in and camber being the main factors. Camber mainly accelerates shoulder wear, i.e., uneven wear, while incorrect toe-in (too large or too small) primarily accelerates wear on the inner and outer sides of the tire.
10
2
Share

Are all new vehicles exempt from inspection when being registered?

Newly registered vehicles are exempt from inspection for six years, but this only applies to non-commercial vehicles with seven seats or fewer. However, owners still need to collect the inspection sticker within each cycle (once every two years), which can now be done online. For newly registered small private passenger vehicles: They are exempt from on-site inspection for six years, but owners must still apply for the annual inspection and environmental labels on time (once every two years within the six-year period). This applies to non-commercial small private passenger vehicles with fewer than seven seats registered after August 31, 2010. No on-site inspection required for six years: According to the new regulations, no on-site inspection is required for six years. However, owners must still provide proof of compulsory traffic accident liability insurance, proof of vehicle and vessel tax payment or exemption, and resolve any traffic violations or accidents before applying for the inspection sticker directly from the traffic management department. (The vehicle must not have been involved in any fatal accidents during this period.) After six years, on-site inspection is required.
4
3
Share

Is it normal for a new automatic transmission car to make noise when stepping on the brake and turning the steering wheel?

It is normal for a new automatic transmission car to make noise when stepping on the brake and turning the steering wheel. This could be due to the break-in period of the new car, or it might be caused by sand particles getting between the brake pads and discs, resulting in friction noise. Automatic transmission gear classifications: Generally, the gears of an automatic transmission car can be divided into P, R, N, D, S, L, and M gears. Precautions for driving an automatic transmission car: Driving an automatic transmission car using only the parking gear P, reverse gear R, neutral gear N, and drive gear D can fully meet the needs of general driving. However, in some special driving environments, other functional gears may be required. Therefore, if the correct control method is chosen, an automatic transmission car can perform better than a manual transmission car. When waiting at a red light, whether to use N gear or D gear depends on personal preference. Temporarily stopping and holding the brake in D gear will not harm the car, because the torque converter in the transmission is equipped with a reaction wheel with a one-way clutch, which amplifies the torque from the engine crankshaft.
6
5
Share

Is It Normal for a New Car Engine to Have Sludge?

It is normal for a new car engine to have sludge. Reasons for sludge in the engine: When the car frequently operates at low speeds, the crankcase temperature remains low. Additionally, the fuel injection volume is higher during low-speed engine operation, causing some incompletely burned gasoline to enter the crankcase, resulting in low-temperature sludge. When the crankcase ventilation valve is partially or completely blocked by oil impurities or sludge, waste and water vapor inside the crankcase cannot be discharged in time, leading to sludge formation. To improve fuel economy, some high-performance direct-injection engines on the market use a technology called lean combustion, which reduces fuel injection. In China, due to poor fuel quality and lean combustion, exhaust gases entering the crankcase contain higher nitrogen oxide levels, contributing to sludge formation. Additionally, low-quality engine oil and gasoline can also cause sludge. Introduction to sludge: Sludge is a deposit formed in the engine during operation when impurities in the crankcase combine with thickened engine oil under high temperatures. It adheres to components such as the engine camshaft, crankcase, oil passages, and oil pan. Both sludge and carbon deposits are harmful substances that negatively impact engine performance.
6
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.