Where are the physical examination locations for driver's license renewal in Huizhou?

1 Answers
StAubree
07/30/25 8:11am
Driver's license renewal physical examination forms must be processed at county-level or military regiment-level medical institutions. Below is relevant information: Driver's License: The full name of a driver's license is motor vehicle driver's license, also known as "driving license," which is the certificate required by law for motor vehicle drivers. Regulations: Driving a motor vehicle requires certain driving skills. Without these skills, driving a motor vehicle arbitrarily may lead to traffic accidents. Generally, people cannot drive on the road without a license. However, for those who have mastered safe driving techniques, the document that permits them to drive vehicles on the road is the "driver's license." This indicates that a driver's license is a type of "permit."
Was this review help?
7
1
Share
More Forum Discussions

What are the functions of the center console buttons in the 2011 Highlander?

2011 Highlander center console button functions include the Electronic Stability Program (ESP). Below are the relevant details: 1. Functions: The 2011 Highlander features parking radar/camera, with the center display showing the rearview image and the radar emitting an alarm when detecting nearby obstacles. The internal circulation mode keeps the air inside the vehicle closed, while the external circulation mode allows air exchange between the inside and outside of the vehicle. It is generally recommended to use the internal circulation mode in congested traffic or poor external air quality. On highways, switch to external circulation approximately every hour to refresh the air inside the vehicle and prevent oxygen deprivation. The vehicle also includes auto hold and auto start-stop functions. 2. Door buttons: On the driver's door of the Highlander, there are buttons for rear window lock, one-touch window control switches, side mirror adjustment switches (for angle adjustment and folding function), and central lock buttons. The roof buttons include controls for the sunroof, lights, sunshade, and welcome lights.
13
2
Share

Why the high beam of the 2011 Cruze does not light up?

2011 Cruze high beam does not light up for the following reasons: 1. Check the fuse: You should check whether the fuse is in good condition. Most of the reasons are caused by the bulb fuse being blown. 2. Circuit failure: Poor or loose wiring connections, or connectors not being properly seated may cause the car headlights not to light up. 3. Wire overheating: Overheating of wires leads to increased resistance in the circuit, reducing the intensity of the headlights. In severe cases, the headlight circuit may short-circuit due to the insulation layer of the wires melting, or even cause the circuit to burn out or lead to a car fire. If the contacts of the lighting circuit control relay or combination switch are corroded or stuck, the circuit may not be able to turn off or on, resulting in weak or no lighting.
14
0
Share

What does the 'a' behind the electronic handbrake mean?

Electronic handbrake followed by 'a' refers to the auto-hold system. The auto-hold system is a technical application in automobiles that enables automatic handbrake functionality during operation. This technology allows drivers to avoid prolonged braking when the vehicle comes to a stop and prevents unnecessary vehicle sliding when the automatic electronic parking brake is activated. The functions of the auto-hold system are: 1. Replacing the driver's manual pulling of the parking brake lever with a single button press, making it simple and effortless, thereby reducing the driver's operational intensity; 2. Enabling basic functions such as static parking, static release (deactivation), and automatic release (deactivation).
20
2
Share

How to replace brake pads for an electronic parking brake?

The method for replacing brake pads on an electronic parking brake is as follows: 1. Locate the jacking point and use a jack to lift the section requiring replacement off the ground; 2. Remove the tire using tools; 3. Expand and loosen the brake caliper; 4. Remove the caliper screws and take out the old brake pads; 5. Install the new brake pads, ensuring they are securely and properly seated; 6. Tighten the caliper screws with a wrench; 7. Reinstall the tire and remove the jack. An electronic parking brake integrates the temporary braking function during driving with the long-term parking brake function, achieving parking brake technology through electronic control.
9
0
Share

How to Replace the Air Filter in Emgrand GS?

Emgrand GS air filter replacement method is: 1. Open the glove box cover on the passenger side; 2. Press the fixing buckle of the cover and pull it outward with force; 3. After removing the rear cover, take out the entire glove box to expose the air filter; 4. Pull the old air filter outward and replace it. Functions of the air filter: 1. Ensure the air filter fits tightly against the housing to prevent unfiltered air from entering the cabin; 2. Separate dust, pollen, and solid particles from the air; 3. Adsorb moisture, soot, ozone, odors, and carbon oxides from the air; 4. Prevent the car windows from fogging up, maintaining clear visibility for the driver and passengers; 5. Ensure clean air in the cabin, preventing bacterial growth and creating a healthy environment.
16
5
Share

Does a dead battery need to be replaced?

A dead battery does not necessarily need replacement; it can simply be recharged. The method for charging a car battery is as follows: 1. Turn off the engine; 2. Open the vent caps on the battery; 3. Attach the red clamp of the dedicated charger to the battery's positive terminal marked with a plus sign, and the black clamp to the negative terminal marked with a minus sign; 4. Set the charger to the 2nd gear and select the 12V power source; 5. Plug in the charger, turn on the switch, and begin charging. Car batteries use lead-acid batteries, which operate on the principle that when the load is connected, the lead on the negative plate reacts with sulfuric acid to form lead sulfate and lose electrons, while the lead oxide on the positive plate reacts with sulfuric acid to form lead and water, gaining electrons, thereby generating an electric current.
2
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.