Where are the headlights located?

1 Answers
OBrantley
07/25/25 6:24am
Headlights are located on both sides of the front end of a vehicle. Below are relevant introductions: Requirements for illumination distance: To ensure driving safety, it is necessary for the driver to identify any obstacles on the road within 100 meters ahead. The high beam of a car is required to illuminate a distance of more than 100 meters. This data is determined based on the vehicle's speed. As modern vehicle speeds increase, the required illumination distance may also increase. The low beam of a car illuminates a distance of about 50 meters. The primary requirements for positioning are to illuminate the entire road surface within the lighting distance and to avoid deviating from the road surface. Anti-glare requirements: Vehicle headlights should be equipped with anti-glare devices to prevent the driver of an oncoming vehicle from being dazzled during nighttime encounters, which could lead to traffic accidents. During nighttime encounters between two vehicles, the beam is tilted downward to illuminate the road surface within 50 meters ahead, thereby avoiding dazzling the driver of the oncoming vehicle.
Was this review help?
5
3
Share
More Forum Discussions

How to Repair Scratches on Car Interior Plastic?

If the scratched area is smooth, first use sandpaper to roughen it, then clean it thoroughly. Apply shoe polish for coloring, let it dry slightly, and then apply silicone rubber, spreading it evenly. After about 10 minutes, gently press with a towel to create a matte effect. Check multiple times, and if it becomes smooth, press again with the towel.
6
3
Share

How to Remove the Steering Wheel of a BMW X1?

Turn off the vehicle and ensure it is stationary. Remove the screw on the left side of the steering wheel. Then, take out the screw at the bottom of the steering wheel. There is a hole underneath the steering wheel. Insert an object into it and push to remove the steering wheel.
12
1
Share

How to Use a Keyless Ignition System?

First, without pressing the brake, press the start button. At this point, the ACC light will illuminate. Press the button again, and the vehicle will begin its self-check. Press the brake and then the start button to ignite the engine; release the foot brake, and you can choose to warm up the car while stationary. Press the foot brake again, shift into D gear, and release the handbrake; release the foot brake, press the accelerator, and you can start driving normally.
1
1
Share

How to Repair a Seat Belt That Won't Pull Out

Adjust the height of the height adjuster to give the seat belt extra retraction capacity, thereby restoring its retraction performance. Smooth out the seat belt and gently pull it back and forth at the entry and exit points. Once the seat belt retracts smoothly, slowly pull it out. There may be a mechanical failure where the seat belt connects to the interior of the car. In this case, it is necessary to go to a 4S shop for disassembly, inspection, and repair.
10
3
Share

How to Turn On the Car Air Conditioning Cooling?

Generally, the buttons on the left side of the car steering wheel represent different temperature settings: blue for cold air, red for warm air, and the middle for a moderate temperature. Adjust the left button towards the blue area, set the fan control knob to the desired speed, and then press the A/C switch to turn on the cooling.
9
3
Share

How to Replace the Timing Belt on a Sonata?

Align the mark on the camshaft timing gear with the mark on the valve cover, and align the mark on the crankshaft timing gear with the mark on the front cover. Install the timing belt in sequence onto the crankshaft timing gear, water pump pulley, idler pulley, camshaft timing gear, and tensioner pulley. Compress the automatic tensioner pushrod to the lowest position, insert a steel pin into the hole, and adjust the pulley using a snap ring pliers. Rotate counterclockwise until the two adjustment holes on the pulley are parallel to the ground, tighten the fixing bolt, and remove the steel pin. Rotate the crankshaft clockwise two full turns and check if the timing marks are correctly aligned.
5
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.