Where are the drainage holes located on the Geely Boyue Pro?

3 Answers
DeJanelle
07/29/25 3:25pm
The Geely Boyue has drainage holes in the sunroof, all four doors, both sides of the rear bumper, and under the wipers. Below are the specific details about the Geely Boyue: 1. Body dimensions: The Geely Boyue measures 4519mm in length, 1831mm in width, and 1694mm in height, with a wheelbase of 2670mm. It has a fuel tank capacity of 58 liters and a curb weight of 1575kg. 2. Powertrain configuration: The vehicle features a MacPherson strut front suspension and a multi-link independent rear suspension. The Geely Boyue is equipped with a 1.8T 184hp L4 turbocharged engine paired with a 7-speed dual-clutch transmission. It delivers a maximum power of 135kW at 5500rpm and a maximum torque of 300Nm between 1750-4000rpm, with a top speed of 200km/h.
Was this review help?
17
5
Share
McVincent
08/14/25 8:18am
I've been driving a Geely Boyue Pro for three or four years, and the drainage holes are mainly located in several key areas. The sunroof drainage holes are at the four corners of the sunroof tracks, each with a small opening specifically designed to drain rainwater. If you look closely at the edges of the tracks, you'll notice the holes in the grooves. The door drainage holes are near the bottom sealing rubber strips of the doors—just lift the seals slightly to find small drainage holes that help drain water accumulated inside the doors. Sometimes, there are similar small holes along the edges of the trunk lid to prevent water buildup in the trunk. Once, I neglected cleaning, and the sunroof holes got clogged, causing rainwater to leak into the car and soak the seats. Since then, I've made it a habit to clean these holes every two or three months using a soft brush or compressed air to keep them clear. Maintaining proper drainage is crucial to prevent mold in the interior or rust on the body. When parking, I try to choose open spaces and avoid parking under trees to minimize leaf debris clogging the holes. Taking good care of these small holes can extend the car's lifespan by several years—it's definitely worth the effort.
Was this review help?
7
3
Share
Expand All
VanAbel
10/11/25 8:28am
As a new owner of the Boyue Pro, I was initially confused when searching for the drainage holes, but after studying the manual, I realized their crucial locations. The sunroof drainage holes are positioned at the ends of the sliding rails, featuring two small openings where water drains out. The door drainage holes are concealed beneath the bottom sealing strips—gently lifting them reveals the holes, which can be cleared with a light poke using a tool. I also discovered that the trunk may have drainage designs around the cover edges to prevent water leakage. After each rain, I quickly inspect these holes, using a cotton swab or needle to lightly remove any debris, avoiding blockages that could lead to moisture buildup and electrical damage. Relatedly, maintaining these small holes is hassle-free and prevents costly repairs. My routine includes a monthly check, combined with window cleaning, to enhance driving safety and comfort.
Was this review help?
15
0
Share
Expand All
More Forum Discussions

How to Replace the Cabin Air Filter of Baojun 510?

Baojun 510's cabin air filter is installed inside the glove compartment on the passenger side. You can replace it by opening the glove compartment. The replacement steps for Baojun 510's cabin air filter are as follows: 1. First, unscrew the two plastic screws on the outside. 2. Then remove the sponge protective panel. 3. Push the support plate under the filter firmly to remove it. 4. Take out the old filter and replace it with a new one. 5. Finally, reassemble by following the previous steps in reverse order. Tip: After absorbing impurities and dust for a period of time, the cabin air filter itself will become contaminated and can no longer purify or filter the air. Continued use will actually worsen pollution, leading to insufficient cooling, weak airflow from the vents, unpleasant odors, and other issues. Under normal circumstances, it is generally recommended to replace the cabin air filter every 10,000 kilometers or approximately once a year.
4
4
Share

What to Pay Attention to When Replacing a New Cylinder Head Assembly?

Ensure the cylinder gasket is properly installed and sealed to prevent oil leaks, and most importantly, the timing must be correctly aligned. Below are relevant details: 1. Composition: The engine is not a single unit; it consists of many parts. From top to bottom, the engine is composed of the valve cover, cylinder head, cylinder block, and oil pan. Inside the engine, there are components such as the crankshaft, connecting rod, piston, valves, and camshaft. 2. Performance: If the cylinder head of the engine is opened, it may affect the engine's performance because the installation process of an aftermarket cylinder head is not as precise as the original factory installation, which could impact the engine's performance. When installing the cylinder head, always use a specialized torque wrench to tighten the bolts according to the specified torque, and follow the prescribed sequence for tightening the bolts.
14
1
Share

How to reset tire pressure on Infiniti Q50?

Infiniti Q50 tire pressure needs to be restored to normal values before resetting the tire pressure data. The following is an introduction to vehicle tire pressure: 1. Service life: Both over-inflation and under-inflation will shorten the tire's service life. Under-inflation increases tire body deformation and tire contact area, leading to sidewall cracks, excessive heat generation, rubber aging, and accelerated shoulder wear. 2. Increased load: Over-inflation causes excessive stretching deformation of tire cords, reduces tire elasticity, and increases the load on the vehicle during driving. 3. Follow recommended values: The tire pressure should be set according to the manufacturer's recommended values. Recommended pressure values can usually be found in the following locations: vehicle user manual, label near the driver's door (B-pillar), drawer beside the driver's seat, or fuel tank cap door.
20
5
Share

How many seconds does the Elantra take to accelerate from 0 to 100?

The actual measured 0-100km/h acceleration time for the Hyundai Elantra 1.8L model is 10.41 seconds. The 0-100km/h acceleration time refers to the time taken to accelerate from standstill to 100km/h, which is the most intuitive reflection of a car's power. Below is some relevant information about it: 1. Global Model: The Elantra is a global model from Hyundai that was first launched overseas. The 'Elantra' has an undeniable 'international flair'—it has swept across four continents worldwide, achieving remarkable success. 2. Interior: The color scheme remains the standard gray upper and beige lower, with a yellowish tone, which is characteristic of Korean cars, emphasizing a homely atmosphere. The silver-gray bright strips adorned from top to bottom in the center are stylish yet not abrupt.
17
0
Share

How Many Days Does It Take to Check for Illegal U-Turns on Double Yellow Lines?

Violation information is generally received via SMS notification within 3-7 days. Below are the specific details for checking traffic violations of motor vehicles: 1. If a motor vehicle commits a violation: If a penalty is required according to regulations, the public security network usually publishes the violation information within 7 working days. 2. If a motor vehicle is involved in a violation captured by electronic monitoring: The processing time for electronic monitoring by traffic police is approximately 3-5 working days. Whether the vehicle is suspected of a violation can generally be checked after about a week. If no results are found, it can be reasonably assumed that no violation occurred. 3. Violations across provinces, municipalities, or autonomous regions: The time for publishing violation information mentioned above applies within the same province, municipality, or autonomous region. For violations across different provinces, municipalities, or autonomous regions, the query time may extend to more than 15 working days.
7
2
Share

How to Steer the Wheel When the Vehicle Skids in Subject 4?

Subject 4 methods for steering the wheel during vehicle skidding should be handled under the following situations: 1. Front-wheel skid: If the front wheels skid, maintain the throttle and correct the direction to drive out. 2. Rear-wheel skid: When the rear wheels skid, turn the steering wheel in the direction of the skid, and after the rear wheels straighten, return to the road. 3. Rear-wheel skid on a downhill slope: When encountering a rear-wheel skid on a downhill, gently press the throttle to increase speed slightly, and after the skid is eliminated, resume the original speed. Note: The key to handling a vehicle skid is to stay calm and avoid panic. If you are unaware of the correct handling methods for a skidding vehicle, improper operation can easily lead to a more severe crisis.
14
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.