Where are the drainage holes located at the bottom of the Baojun 310?

2 Answers
McGriffin
08/31/25 7:04am
The drainage holes at the bottom of the Baojun 310 are located on the lower side rails. All vehicles are equipped with drainage holes: All vehicles are equipped with drainage holes, which serve as outlets to drain accumulated rainwater from the vehicle to the outside. The design principle and structure are relatively simple, and almost all vehicles are configured with drainage outlets. However, these drainage holes are prone to clogging, so drivers need to regularly check whether the vehicle's drainage outlets are functioning properly. Near the car doors: The drainage holes are usually located near the car doors. If they cannot be found, you can refer to the vehicle's user manual for assistance in locating them. Keeping these drainage holes clear helps maintain the vehicle's body dryness and prevents corrosion.
Was this review help?
20
4
Share
CollinDella
09/13/25 3:24am
The drainage holes of the Baojun 310 are mainly located at the bottom edges of the four doors and the bottom groove of the trunk. There are usually two or three coin-sized openings under the doors. Every time after washing the car, I noticed water accumulation in the door gaps, so I specifically asked a technician to teach me how to use thin wire to unclog the drainage holes. There’s also a small hole inside the fuel cap that’s easy to overlook—my friend’s car once rusted because it got blocked. Actually, the location diagram is marked on page 35 of the manual. I recommend cleaning these holes during routine maintenance by simply removing leaves and mud. It’s best to check them before the rainy season to avoid moldy interiors and costly repairs, especially since leaks can be a big hassle once the seals age.
Was this review help?
18
0
Share
Expand All
More Forum Discussions

What is the difference between Benben EC and EV?

The differences between Benben EC and EV: 1. Different tire models: Benben EC tire model is 165/60R14; Benben EV tire model is 175/60R15. 2. Different power: Benben EC motor has 61 horsepower; Benben EV motor has 75 horsepower. The body dimensions of Benben EV are: length 3730mm, width 1650mm, height 1530mm, wheelbase 2410mm, front track 1420mm, rear track 1430mm. The suspension system of Benben EV is: torsion beam non-independent suspension and MacPherson independent suspension.
2
3
Share

What is the method to reset the maintenance wrench on the Emgrand GS?

The method to reset the maintenance wrench on the Emgrand GS is: 1. Turn off the ignition switch, then press and hold both arrow buttons simultaneously, and turn on the ignition switch; 2. After the ignition switch is turned on for 3 seconds, release both arrow buttons; 3. Press and hold the SET button for more than 3 seconds, then press the MODE button; 4. Turn off the ignition switch to complete the reset. The Emgrand GS is equipped with a 1.5T turbocharged engine, delivering a maximum horsepower of 141 PS, a maximum torque of 235 Nm, a maximum power of 104 kW, a maximum power speed of 5200 rpm, and a maximum torque speed range of 1400 to 4000 rpm. It is paired with a 6-speed manual transmission.
8
3
Share

Can the engine start after bearing failure?

Engine bearing failure prevents startup. Engine bearing failure refers to abnormal noises in the crankshaft area of a car engine. If this condition occurs during normal driving, the vehicle should be stopped for inspection. The primary causes of engine bearing failure are wear or insufficient lubrication. Engine classifications: 1. According to the working method of the intake system, they can be divided into naturally aspirated, turbocharged, mechanically supercharged, and twin-charged engines; 2. Based on piston movement, they can be categorized as reciprocating piston internal combustion engines and rotary piston engines; 3. According to cylinder arrangement, they are classified as inline engines, V-type engines, and horizontally opposed engines.
12
3
Share

At what level of wear should brake discs be replaced?

Brake discs should be replaced when the wear exceeds 2mm. The method for removing brake discs is as follows: 1. Remove the wheel and take off the dust cover; 2. Disconnect the brake pad sensor plug from the bracket; 3. Unscrew the brake caliper fixing bolts; 4. Remove the brake caliper housing and secure it to the car body with a metal wire; 5. Remove the brake pads from the brake caliper housing. Brake disc maintenance: 1. Pay attention to protecting the brake discs when washing the car; 2. Reduce brake disc wear; 3. Minimize foreign objects entering the braking system and replace with qualified brake pads; 4. High-temperature protection for brake pads; 5. Lubrication maintenance for brake calipers.
19
4
Share

Is the xc60 domestically produced or imported?

xc60 is imported. Taking the 2021 Volvo xc60 as an example, it is equipped with a 2.0t inline 4-cylinder turbocharged engine, with a maximum horsepower of 190ps, a maximum torque of 300nm, a maximum power of 140kw, a maximum power speed of 5000rpm, and a maximum torque speed ranging from 1400 to 4000rpm. It is paired with an 8-speed automatic transmission. The dimensions of the 2021 Volvo xc60 are: length 4688mm, width 1902mm, height 1658mm, wheelbase 2680mm, and minimum ground clearance of 216mm.
13
0
Share

What are the available MPV models with four-wheel drive?

MPV models with four-wheel drive include: Honda Odyssey, Honda Elysion, Buick GL8, Toyota Alphard, Toyota Sienna, BYD Song MAX, Volkswagen Multivan, Volkswagen Sharan, etc. Taking the Buick GL8 as an example, it is equipped with a 2.0T direct-injection 4-cylinder turbocharged engine, with a maximum horsepower of 174ps, a maximum torque of 350Nm, and a maximum power of 237kW. The Buick GL8 has the following body dimensions: length 5219mm, width 1878mm, height 1805mm, wheelbase 3088mm, minimum ground clearance 190mm, and a body weight of 1930kg.
20
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.