When will the FAW-Volkswagen Jetta VS5 be launched?

What is the difference between China III and China IV motorcycles?

The main difference between China III and China IV motorcycles is the reduction in sulfur content, and more importantly, the decrease in pollutant emissions. The most significant distinction between China IV and China III motorcycles is the improved emission standards. Whenever emission standards are raised, both the price and performance of motorcycles will change. To meet the emission standards, China IV motorcycles have replaced the traditional carburetor with an electronic fuel injection system and upgraded the motorcycle's exhaust system. Electronic fuel injection is the core difference between China III and China IV motorcycles. However, many riders are aware that numerous China III motorcycles are already equipped with electronic fuel injection, so why don't they meet China IV standards? Therefore, while electronic fuel injection is the fundamental difference between China III and China IV motorcycles, there are other factors as well. The electronic fuel injection system in China IV models is superior to that in China III models. After a period of research and development, the performance of electronic fuel injection has improved significantly compared to when it was first introduced. After adjustments, it now meets the current China IV standards, whereas the original China III electronic fuel injection performance was slightly inferior. China III and China IV are both motor vehicle emission standards, also known as the third and fourth-stage emission standards. They are formulated with reference to Euro III and Euro IV standards, but some criteria are even stricter than Euro III and Euro IV, primarily aimed at limiting the content of harmful gases in exhaust emissions, reducing air pollution, and protecting the environment. Motorcycles that comply with Euro III and Euro IV standards require certain technical upgrades.

8

0

Share

What does the EPC light on a car indicate?

The EPC indicator light can illuminate in two scenarios: during the power-on self-test and under other circumstances. The power-on self-test is a diagnostic check of all vehicle sensors before driving. Typically, if the engine is not started, the light will turn off by itself after about 3 seconds. If the EPC light remains on after starting the vehicle or illuminates under other conditions, the possible causes include faults in the engine intake system, throttle body, fuel system, engine, ECU control unit, or brake lights. Here is a detailed explanation of the reasons for the EPC light illuminating under other conditions: Engine intake system fault: The EPC light will activate if the engine intake is obstructed or insufficient. Throttle body fault: Carbon buildup is a common issue with the throttle body. Additionally, dirt accumulation can affect intake, triggering the light. Fuel system fault: Issues such as substandard fuel, fuel degradation, or poor fuel atomization can cause the light to illuminate. Engine fault: Insufficient engine pressure or problems with components like the intake valves can also activate the EPC light. ECU control unit fault: Interference with the vehicle's computer signals or false alarms from the computer may trigger the light. Brake light fault: Malfunctions like non-functioning brake lights, faulty brake switches, or brake circuit issues can cause the EPC light to illuminate. Solutions for the EPC light: Troubleshoot intake system issues, use the correct fuel grade, clean the throttle body, etc. Remove carbon deposits from relevant components. Re-flash ECU data. If the EPC light comes on, the driver can first try turning off the engine and restarting it to see if the light remains illuminated. If it turns off, there may be no issue, and the light could have been triggered by a temporary glitch. If the light stays on or frequently illuminates, the vehicle should be taken to the nearest service center for professional diagnosis and repair to eliminate potential safety hazards. The full English name of EPC is Electronic-Power-Control, which translates to electronic power control. Most people refer to it as the engine electronic stability system. The EPC system primarily includes controllers and sensors related to the powertrain. When sensor data deviates from normal parameters, the EPC system takes predefined actions to manage the powertrain. The EPC indicator light typically appears in two colors: yellow and red. A yellow EPC light indicates a fault, but the vehicle can still be driven cautiously to a repair facility. A red EPC light signifies a severe issue, requiring immediate stopping of the vehicle and contacting a professional for repairs. Continuing to drive with a red EPC light can damage core components or compromise safety.

2

3

Share

What does the yellow exclamation mark warning light in CRV mean?

The exclamation mark on the car dashboard indicates that the system has an abnormality or malfunction. There are many indicator lights on the car dashboard with exclamation marks, such as the tire pressure indicator light, lighting fault indicator light, steering system fault indicator light, brake system fault light, transmission fault indicator light, and wiper fault indicator light. Below is a detailed introduction to the exclamation mark warning lights: General faults: An exclamation mark inside a triangle. If this symbol lights up, it indicates a fault in the car's general performance, components, or functions. Main issues include parking sensor faults, fuel cut-off system intervention or faults, external light faults, engine oil pressure sensor faults, etc. It is necessary to go to a 4S shop for inspection to identify the source of the fault. Automatic transmission fault: A yellow gear with an exclamation mark inside. This is the automatic transmission fault warning light, indicating that there is a fault in the transmission or the transmission lubricant is below the normal range. The transmission oil should be replaced promptly. Brake system fault: An exclamation mark inside a circle with parentheses. This represents a brake system warning, mainly indicating a brake system fault or low brake fluid level. The brake system should be inspected immediately to avoid accidents. Tire pressure abnormality: An exclamation mark with a horizontal line below parentheses. This represents the tire pressure monitoring warning light. When the car's tire pressure is too low, this warning light will come on. Check the car's tire pressure and restore it to the normal range. Lighting fault: A yellow bulb with an exclamation mark. This is the lighting fault indicator light, indicating that a car light has malfunctioned. Solution: Go to a 4S shop as soon as possible for inspection and repair, or check it yourself. Focus on commonly used bulbs such as turn signals, fog lights, and interior lights to identify the problem. In addition, during daily use of the vehicle, the warning lights displayed on the dashboard are divided into two different colors: yellow and red: Yellow indicates that there is a fault in the corresponding system, but the problem is not very serious. Reduce speed and proceed to the corresponding repair point for maintenance to eliminate potential safety hazards in time. Red indicates that there is a very serious problem in the corresponding system. If this happens, do not continue driving. Pull over immediately and call for professional assistance to prevent unpredictable dangers to the vehicle and personal safety caused by forced driving. It should be noted that when the car is started, all lights will turn on, and the system will perform an automatic check. After the check is completed, the lights will turn off automatically. If a light does not come on when the ignition is turned on, stays on continuously, or lights up while driving, it means that the related system has a fault. In such cases, seek professional help promptly for car inspection and elimination of safety hazards.

5

4

Share

How Much Fuel Can a 48V Mild Hybrid Save?

After multiple tests, it was concluded that 48V mild hybrid technology has no significant impact on vehicle emissions but greatly affects fuel consumption, ideally achieving around 15% fuel savings. The principle of 48V mild hybrid involves adding a 48V auxiliary motor between the engine and transmission without altering the engine compartment layout. It serves two main purposes: first, to save fuel and improve engine smoothness during low-torque phases; second, to reduce the vehicle's electrical load. Below is more related information: Advantages of 48V Mild Hybrid: 1. Electrical Load: Many drivers encounter situations where they idle the car while waiting, listening to music or the radio to pass the time. The vehicle's electrical system operates at only 12V, and turning on the air conditioning, audio system, or other electronics further increases the load. Without the engine running, the battery might drain in just a few minutes, making it impossible to start the car. A 48V mild hybrid system, however, comes with a higher-capacity battery, allowing drivers to listen to music with the engine off and use more onboard electronics without worry. The system will start the engine when the battery is nearly depleted to prevent a complete discharge. 2. Fuel Savings and Low-Torque Smoothness: Engines often lack power during low-torque phases, especially small-displacement turbocharged engines, requiring drivers to press the accelerator harder to compensate. This results in higher fuel consumption. The 48V mild hybrid auxiliary motor addresses this issue by intervening during vehicle startup to reduce engine load and smooth out the jerky feeling caused by insufficient low-torque output. During driving, the 48V mild hybrid, like plug-in hybrid models, performs energy recovery to further save fuel. 3. Performance: The Changan CS55 equipped with a 48V mild hybrid system feels noticeably more responsive during startup compared to conventional models. As for fuel savings, the effect is impressive. The advantage in electrical load management is particularly evident, eliminating concerns about battery drain.

10

0

Share

What brand is MRXUS?

MRXUS is a vehicle under SAIC Maxus, whose full name is SAIC Maxus Automobile Co., Ltd., a wholly-owned subsidiary of SAIC Motor Corporation Limited. SAIC Maxus models include the wide-body light passenger V80, MPV G10, SAIC Maxus RV RV80, SUV D90, and pure electric wide-body light passenger EV80. Taking the SAIC Maxus MRXUS V80 manual classic city delivery king short wheelbase medium roof as an example, its body dimensions are: length 4950 mm, width 1998 mm, height 2345 mm, wheelbase 3100 mm, and fuel tank capacity 80 liters.

20

0

Share

What kind of car is the Axela?

Axela is a compact sedan produced by Changan Mazda. Taking the 2020 Axela as an example, its body dimensions are: length 4662mm, width 1797mm, height 1445mm, with a wheelbase of 2726mm and a fuel tank capacity of 50 liters. The 2020 Axela is equipped with a 1.5L naturally aspirated engine, delivering a maximum horsepower of 117ps and a maximum power of 86kw, paired with a 6-speed manual transmission. It features a MacPherson strut front suspension and a torsion beam rear suspension.

10

0

Share

When will the FAW-Volkswagen Jetta VS5 be launched?

What is the difference between China III and China IV motorcycles?

What does the EPC light on a car indicate?

What does the yellow exclamation mark warning light in CRV mean?

How Much Fuel Can a 48V Mild Hybrid Save?

What brand is MRXUS?

What kind of car is the Axela?

Under what circumstances will the car alarm go off?

Reasons for the Brake Pedal of Changan CS35 Being Hard to Press

What is the fuel tank capacity of the Mercedes-Benz B200?

What Happens If a Car Is Left Unused for a Week?