When will the China VI emission standards be implemented?

1 Answers
Leonard
07/25/25 6:55am
Currently, the country has divided the "China VI Standard" into two phases: "China VIa" and "China VIb", which will be uniformly implemented nationwide in 2020 and 2023 respectively. Here is an introduction to the China VI Standard: 1. The China VI Standard, also known as the "National Sixth Stage Emission Standards for Motor Vehicles", is established to implement environmental protection laws, reduce and prevent pollution from vehicle exhaust, protect the ecological environment, and ensure human health. 2. The China VI Standard was issued by the Ministry of Environmental Protection and the General Administration of Quality Supervision, Inspection and Quarantine on December 23, 2016, and June 22, 2018, respectively. The "Limits and Measurement Methods for Emissions from Heavy-Duty Diesel Vehicles (China VI)" came into effect on July 1, 2019. The implementation of the China VI Standard will impose stricter requirements on emissions such as carbon monoxide, nitrogen oxides, and hydrocarbons. 3. Based on past experience, when the China V Standard was implemented, vehicles meeting the China II Standard were phased out. Therefore, it is highly likely that vehicles meeting the China III Standard will also be phased out after the implementation of the China VI Standard. The timing of the phase-out will depend on national policies and the actual conditions of each region.
Was this review help?
6
0
Share
More Forum Discussions

What are the causes of abnormal brake noise?

The causes of abnormal brake noise are: 1. Metal particles or small gravel between the brake pads and brake discs; 2. Excessive wear of brake discs or brake drums; 3. Overly hard brake pads; 4. Rust in the brake calipers; 5. Inflexible handbrake cables; 6. Slow return of the master brake cylinder. Solutions for abnormal brake noise in cars include: 1. Checking if there are lubrication issues with the top rubber or buffer rubber of the shock absorbers; 2. Running-in new brake friction pads; 3. Timely replacement of brake pads; 4. Removing foreign objects from the surface of the brake discs. The car's brake pedal is located below the steering wheel. Pressing the brake pedal causes the brake linkage to be pressurized and transmitted to the brake pads on the brake drum, which then clamp the brake rotor, slowing down or stopping the car.
20
5
Share

How Long Does a Driver's License Take to Expire and Become Invalid?

The obtained driver's license will become invalid after three years of expiration, at which point you need to retake the driver's license test. If the expiration is less than one year, you can renew the license normally. If the expiration is between one and three years, the license will be canceled, but you can renew it by passing the subject one test. If the expiration exceeds three years, the license becomes invalid and cannot be renewed. During the expiration period, you are not allowed to drive a motor vehicle; otherwise, it will be treated as driving without a license, resulting in a fine and possibly up to 15 days of detention. Therefore, a driver's license that has been expired for more than three years will become invalid. Latest Deadline for License Renewal: There is no need to worry too much about an expired driver's license because there is a latest deadline for renewal. However, it is important to note that you cannot drive a motor vehicle after the license expires; otherwise, it will be treated as driving without a license. If the license has been expired for less than one year, the renewal process follows the normal procedure. If the license has been expired for more than one year but less than three years, the license will be canceled, but you can renew it by passing the subject one test. If the expiration exceeds three years, the license becomes invalid and cannot be renewed. Documents Required for Renewal: ID card and its copy; original driver's license; recent 1-inch color photos with white background (3 copies); application form for motor vehicle driver's license (available at the processing location, filled out by the agent if applicable); medical examination certificate (issued by a local county-level or higher medical institution, or a military medical institution at the regiment level or above, or a designated vehicle management office); if you are not a local resident, you also need to provide the original and copy of your local residence permit.
17
3
Share

What are the steps for driving and parking a manual transmission car?

Manual transmission driving steps are: 1. Fully depress the clutch pedal; 2. Push the gear lever to engage 1st gear (starting gear); 3. Gently press down the turn signal lever to activate the left turn signal, alerting vehicles front and rear; 4. Press the horn button to notify pedestrians ahead of the vehicle's imminent movement; 5. Release the vehicle's handbrake; 6. Gradually lift the left foot until the clutch reaches the half-engaged position, feeling slight vehicle vibration; 7. As the vehicle begins moving, fully release the clutch while gently pressing the accelerator. Manual transmission parking steps are: 1. When stopping, first depress the brake pedal to decelerate, then press the clutch pedal when speed becomes very low; 2. After complete stop, shift to neutral and engage the handbrake (neutral position prevents accidental throttle input - even if the accelerator is pressed, the vehicle won't lurch forward); 3. Turn the key to shut off the engine.
16
0
Share

How to Turn on the Heater in a Nissan Sylphy?

The method to turn on the heater in a Nissan Sylphy is: 1. If the AC indicator light is on, press the AC button to turn off the cooling switch; 2. Rotate the temperature control dial to the red zone, where the temperature adjustment range is between 18 to 32 degrees Celsius; 3. Adjust to your desired temperature, but do not set it lower than the outside temperature to avoid incorrect temperature control; 4. Rotate the fan speed switch to adjust the appropriate airflow speed. Do not turn on the heater immediately after a cold start. The correct method is to start the engine for preheating first, wait until the water temperature gauge needle points to the middle position, then turn on the heater. Set the air conditioning to external circulation for 2 to 3 minutes to replace the air inside the car, and then switch to internal circulation. The Nissan Sylphy is a compact 4-door, 5-seater sedan with body dimensions of 4631mm in length, 1760mm in width, and 1503mm in height, a wheelbase of 2700mm, and a fuel tank capacity of 50 liters.
16
5
Share

Is It Normal for the Area Under the Rear Car Seats to Feel Hot?

It is normal for the area under the rear car seats to feel hot, which may be due to the high temperature of the exhaust pipe. Types of car seats are as follows: 1. Fabric Seats: Fabric seats, as the name suggests, are primarily made from a chemical fiber material. In simple terms, materials like velvet, cotton, and linen fall into this category. Cleaning these fabric seats is very straightforward. Owners only need to use a vacuum cleaner to remove dust attached to the seats, followed by a gentle wipe with a neutral fiber cleaner and a damp cloth. 2. Genuine Leather Seats: Genuine leather seats, made from real leather, are simple, comfortable, and elegant. Unlike fabric seats, genuine leather seats require regular maintenance. The first point is to avoid direct sunlight; it's best to keep them in shaded areas to prevent UV rays from accelerating fading or cracking. The second point is to use a soft leather cleaner for wiping during cleaning. 3. Synthetic Leather Seats: Many people mistakenly believe that genuine leather and synthetic leather are the same material. In reality, most so-called genuine leather seats on the market are actually synthetic leather. After all, genuine leather seats are quite expensive. This 'synthetic leather' is usually made with a small amount of genuine leather mixed with a certain proportion of artificial or recycled leather. With heavy marketing by some businesses, these synthetic leather seats have quickly secured a place in the market and become the choice for most people.
5
1
Share

What Are the Reasons Why a Car Suddenly Can't Accelerate While Driving?

If a car suddenly can't accelerate while driving, it may be due to dirty fuel, clogged fuel injectors, a faulty fuel pressure regulator, or poor performance of the electric fuel pump. Below are some precautions to take when refueling a car: 1. Refuel in the morning or evening: Gasoline is charged by volume rather than weight, and it expands with heat and contracts with cold. Refueling in the morning or evening when temperatures are relatively lower allows the same volume of gasoline to have a higher mass, saving a significant amount. For example, a 15-degree temperature difference between morning and evening can result in a difference of 0.62 liters. Additionally, the risk of danger is lower at lower temperatures. 2. Avoid filling the tank completely: When driving in the city, there's no need to fill the tank to the brim. A full tank increases the engine's load. It's best not to exceed two-thirds of the tank's capacity, as overfilling can cause overflow. Gasoline may flow into the intake manifold through the pipes, leading to spark plug "flooding," which can cause the car to stall when refueling. In severe cases, the car may fail to start normally, and gasoline may even leak from the carbon canister, posing a significant fire hazard if exposed to open flames. 3. Don't wait until the tank is empty to refuel: The fuel pump in the tank relies on gasoline for cooling. If the fuel level is too low and doesn't cover the pump, prolonged operation under such conditions may reduce the fuel pump's lifespan. This is less of an issue in winter but poses a higher risk in the hotter summer months. Additionally, if the fuel level is too low, the pump may draw sediment from the bottom of the tank, which can clog the pump or block the fuel lines.
17
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.