When will the 2020 new traffic regulations come into effect?

1 Answers
AliceMarie
07/29/25 11:09pm
It will come into effect on January 1, 2020. Here is the relevant introduction about the new traffic regulations: 1. Mandatory implementation of China VI a emission standards: According to the "Limits and Measurement Methods for Emissions from Light-duty Vehicles (China VI)" issued by the Ministry of Environmental Protection and the General Administration of Quality Supervision, Inspection and Quarantine in 2016, light-duty vehicles will mandatorily implement the China VI a emission standards from July 1, 2020, and the China VI b emission standards will be mandatorily implemented from July 1, 2023. 2. New standards for expressway tolls: Starting from January 1, 2020, all toll roads nationwide will uniformly charge tolls according to the new version of the "Toll Road Vehicle Toll Classification". Vehicles with 8 or 9 seats will be reclassified from Class II to Class I, and will be charged as Class I vehicles in the future. At the same time, vehicles without ETC will no longer enjoy the basic preferential policy of no less than 5% in principle for vehicle tolls. 3. Non-stop weighing monitoring on expressways: Previously, the State Council issued a policy stipulating that from January 1, 2020, non-stop weighing monitoring will be implemented at the entrances of closed expressway toll stations. Overloaded and overweight vehicles will not be issued cards, not allowed to pass, and will be advised to turn back, and will not be allowed to enter the expressway.
Was this review help?
11
0
Share
More Forum Discussions

How often should the Honda City's fuel filter be replaced?

The Honda City's fuel filter should be replaced every 40,000 kilometers. The fuel filter, also known as the gasoline filter or fuel filter, is essential because gasoline typically contains various impurities, and over time, the fuel tank accumulates sediment. These factors can affect fuel quality. The fuel filter's role is to remove these impurities, ensuring that the gasoline reaching the engine's combustion chamber is clean and pure. The Honda City is a model under the Honda brand, with body dimensions of 4440mm in length, 1695mm in width, and 1495mm in height, and a wheelbase of 2600mm. In terms of exterior design, the City's front fascia closely resembles that of the Honda Fit, with very pronounced lines on the front fenders. The body features a dual-waistline design, and the rear styling bears some resemblance to the Honda Crider.
4
3
Share

What Does Traction Control Failure Mean?

Traction control failure refers to the situation where the transmission system of wheeled vehicles such as cars, railway locomotives, and bicycles cannot generate sufficient torque to rotate the wheels. Causes of traction control failure and corresponding solutions: Fuel system malfunction: Reduced fuel injection due to fuel system issues, such as clogged injectors, low fuel pressure, or impurities in gasoline. Solutions include replacing fuel, injectors, spark plugs, or the fuel pump. Inaccurate air measurement: Discrepancy between detected and actual air intake due to inaccurate air measurement. This requires inspecting and replacing the air flow meter or oxygen sensor. How the traction control system works: The traction control system is managed by a computer that monitors the speed of all four wheels and the steering wheel angle. During acceleration, if the computer detects a significant speed difference between the driven and non-driven wheels, it immediately identifies excessive driving force and sends a signal to reduce the engine's fuel supply, thereby decreasing the driving force and reducing wheel slip. If the computer detects understeer or oversteer, it similarly reduces the driving force to align with the driver's steering intentions.
12
2
Share

How to identify reference points when exiting parallel parking in Subject 2?

Methods for identifying reference points when exiting parallel parking in Subject 2: 1. Turn your head 135 degrees to the right and look at the wide pillar between the front and rear doors on the right side of the vehicle. There is a black protruding cylindrical pull rod below the rear door window. When the cylindrical pull rod aligns with the front right corner of the parking space, that's the moment to turn the steering wheel fully to the right; 2. Using the rearview mirror, when the rear right corner of the parking space appears as an obtuse angle in the mirror, this position can also be determined by the intersection of the vertical bar of the rear door triangular window and the yellow line at the back of the parking space. When exiting, since the steering wheel is already turned fully to the left, proceed directly until the left front fender ridge of the car touches the right yellow line, then straighten the steering wheel and drive forward. When the right front corner of the car touches the right yellow line, immediately turn the steering wheel fully to the right. You can stick your head out of the window to check if the front wheel is pressing against the yellow line and make appropriate adjustments.
7
0
Share

What Are the Symptoms of a Damaged Car Air Conditioning Blower?

The symptoms of a damaged car blower include no air output, reduced airflow, or the blower not stopping. Below is a detailed explanation of the symptoms and solutions for a damaged car blower: No air output: Prolonged use of the blower can lead to excessive dust accumulation, increasing the friction coefficient between the rotor and bearings, causing the rotor to become obstructed or even jammed, resulting in overheating and damage to the coil. After disconnecting the power, open the blower's rear cover and add a few drops of lubricating oil to the bearing sleeves at both ends of the rotor. While adding oil, rotate the blades until they move freely, which should resolve the blower issue. Reduced airflow: If the blower motor operates normally but some air vents produce abnormal airflow (either too strong or too weak), check for any blockages in the corresponding air ducts, whether the air damper is stuck, or if there are any leaks due to damaged connecting ducts. Repair according to the specific situation after inspection. Blower not stopping: The reasons for the blower not stopping include a faulty compressor start capacitor, burned-out compressor coils, or a malfunctioning control circuit board. Professional inspection and repair at a 4S shop are required.
18
0
Share

What is the impact of toe-in size on handling?

When the toe-in is too small, the steering wheel cannot automatically return to the center, and the car tends to feel unstable at high speeds; when the toe-in is too large, the steering wheel becomes heavy. Looking down from above the car, the two front wheels form a V-shape opening upwards. Front wheel toe-in refers to the distance difference between the front and rear edges of the front wheels in the lateral direction of the car, or it can refer to the angle between the direction of the car's movement and the plane of the front wheels, which is also called the toe-in angle. Measuring toe-in: Before formal measurement, ensure that the front wheel hub bearings are properly tightened and the front tire pressure is normal. Then, park the car on a flat surface with the front wheels in a straight-ahead position, and push the car forward 1-2 meters to eliminate any gaps that may affect the measurement. Adjusting toe-in: Front wheel toe-in can be adjusted by changing the length of the tie rod. During adjustment, follow the measurement position specified by the car manufacturer to ensure that the distance difference between the front and rear of the wheels meets the prescribed toe-in value. Generally, a toe-in value between 0-12mm is considered normal. If the car's tie rod is straight, you can first loosen the lock bolts at both ends of the tie rod, then use a pipe wrench to twist the tie rod to extend or shorten it.
5
5
Share

What are the engine specifications of the 2018 Superb?

The 1.4T version of the 2018 Superb is equipped with an EA211 engine, with a maximum power of 110 kW and a maximum torque of 250 Nm. The 1.8T version features an EA888 engine, delivering a maximum power of 132 kW and a maximum torque of 300 Nm. The 2.0T low-power version also uses an EA888 engine, producing a maximum power of 137 kW and a maximum torque of 320 Nm. The 2.0T high-power version has a maximum power of 162 kW and a maximum torque of 350 Nm. The engines for the 2018 Superb are manufactured in the Changchun Automobile Economic and Technological Development Zone and are domestically produced. For daily maintenance of the 2018 Superb engine, the following methods can be used: Use lubricating oil of the appropriate quality grade. For gasoline engines, select SD--SF grade gasoline engine oil based on the additional equipment of the intake and exhaust systems and usage conditions. For diesel engines, choose CB--CD grade diesel engine oil according to mechanical load, with the selection standard not lower than the manufacturer's requirements. Regularly change the engine oil and filter. The quality of any grade of lubricating oil will deteriorate during use. After a certain mileage, its performance will degrade, leading to various engine issues. To avoid malfunctions, change the oil periodically based on usage conditions and maintain an appropriate oil level. When oil passes through the fine pores of the filter, solid particles and viscous substances accumulate in the filter. If the filter becomes clogged and oil cannot pass through, it may rupture the filter or open the safety valve, allowing dirty oil to bypass the filter and return to the lubrication system, accelerating engine wear and increasing internal contamination. Regularly clean the crankcase. During engine operation, high-pressure unburned gases, acids, moisture, sulfur, and nitrogen oxides from the combustion chamber enter the crankcase through the gap between the piston rings and cylinder walls, mixing with metal particles from component wear to form sludge. Small amounts remain suspended in the oil, while larger amounts precipitate, clogging filters and oil passages, making engine lubrication difficult and causing wear. Periodically use a radiator cleaner to flush the radiator. Removing rust and scale not only ensures normal engine operation but also extends the overall lifespan of the radiator and engine.
14
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.