When to turn the steering wheel back when reversing into the garage?

3 Answers
SanCollin
07/28/25 5:06pm
When reversing into the garage, observe the state of the car's wheels through the rearview mirror to determine the time to straighten the steering wheel. Generally, you can straighten the steering wheel when the wheels pass the right-angle edge of the garage and there is no phenomenon of pressing the line. The following is a partial introduction about reversing: 1. Definition: Reversing refers to the behavior of a motor vehicle moving backward. It also refers to people "transferring" midway during a trip, that is, changing from one car to another. Reversing is more difficult than driving forward, mainly because the view is limited to a certain extent. 2. Safety measures: Before reversing, you should first see the situation behind the car, estimate the reversing route, and determine whether the front of the car will hit obstacles during the reversing process.
Was this review help?
17
5
Share
SanWeston
08/11/25 9:16pm
When I first started learning to drive, reversing into the parking space was quite a headache. The timing of turning the steering wheel back is crucial. It's best to start slowly straightening the steering wheel when the car body forms about a 45-degree angle with the parking space, allowing the car to drive straight in. Observe the rearview mirror; the most accurate moment is when the rear of the car is about to align with the rear corner or side line of the parking space. Common mistakes beginners make include turning the wheel back too early, causing the car to tilt or hit the wall, or turning back too late and crossing the line. I recommend reversing at low speed, using first gear to control the speed, and avoiding sharp turns of the steering wheel to prevent losing control. Another small tip is to adjust the seat height to ensure a full view of the parking space, which is safer. After practicing reversing into the parking space several times, you'll get the hang of it. Remember, safety first—don’t rush to finish.
Was this review help?
3
3
Share
Expand All
Adriel
09/29/25 8:15am
As a seasoned driver with ten years of experience, I rely on intuition when steering the wheel back during reverse parking. I usually start turning the wheel back when about half of the car has entered the parking space, roughly when the rear wheel covers the corner line of the spot. This way, the car smoothly glides in without leaving gaps or causing scrapes. It's also important to check the surroundings outside the car, especially to avoid hitting pedestrians or obstacles. I prefer setting the steering angle first and letting the car naturally align itself, avoiding forceful adjustments. The biggest no-nos in reverse parking are sudden acceleration or hard braking; gently controlling the speed with the clutch and brake is key. Regular practice in residential areas helps build experience and familiarity.
Was this review help?
14
2
Share
Expand All
More Forum Discussions

What does exam appointment location failure mean?

The reasons for exam appointment location failure are as follows: 1. May not meet the ministry's time limit requirements. 2. Too many applicants for a single test site. When the number of applicants for a single exam exceeds the planned number of examinees, students ranked lower will fail to make an appointment. 3. Too many exam sessions applied for. Students can apply for up to five exam sessions simultaneously for a single test, but may only successfully schedule one, with the system indicating failure for the other four sessions. Relevant information about the driver's license exam is as follows: 1. Introduction: The driver's test is a qualification examination organized by the Vehicle Management Office of the Public Security Bureau. Only by passing the driver's test can one obtain a driver's license and legally operate motor vehicles. 2. Content: The motor vehicle driver's test content is divided into the road traffic safety laws, regulations, and related knowledge test subject (also known as the "theoretical test", referred to as "Subject 1"), the site driving skills test subject (commonly known as the "pole test", referred to as "Subject 2"), and the road driving skills and safe civilized driving common sense test subject (commonly known as the "road test", referred to as "Subject 3"). The test content and passing standards are uniform nationwide, with corresponding test items specified according to different permitted driving vehicle types.
17
3
Share

Can maintenance records be checked if not serviced at a 4S shop?

If the vehicle is not serviced at a 4S shop, the maintenance records cannot be checked. Here are some precautions regarding vehicle maintenance: 1. Regularly clean body stains: The paint surface of the vehicle body will deteriorate over time if continuously exposed to stains, leading to dullness and reduced glossiness. Therefore, it is necessary to protect the paint surface by regularly cleaning the body to maintain its cleanliness. 2. Regularly change the engine oil: Engine oil has a limited service life. It is important to replace the vehicle's engine oil periodically, as prolonged use causes the oil to become increasingly turbid, which can damage the car's engine. Hence, special attention must be paid to engine oil maintenance during servicing.
6
0
Share

What does 96Y mean on a tire?

96Y refers to the maximum load capacity and speed rating of the tire. 96 indicates that each tire can bear a maximum load of 710kg, so four tires can support 2840kg in total. Y represents a maximum speed of 300km/h. These are common indicators for maximum load and speed ratings. Functions of tires installed on vehicles: 1. Load-bearing capacity: Supporting the weight of the vehicle and its cargo, known as load-bearing capacity. 2. Dynamic performance: Transmitting forces such as braking, traction, acceleration, steering, and braking to the ground, including driving force, traction force, braking force, and steering force. This is referred to as meeting the dynamic performance requirements of the vehicle, enabling its operation. 3. Safety: Ensuring the vehicle can be driven smoothly, stably, and safely under various weather, road, and speed conditions, known as safety performance.
3
4
Share

Can Small-Displacement Vehicles Drive on the Grassland Sky Road?

Small-displacement vehicles can drive on the Grassland Sky Road. Here are some precautions for driving: 1. Vehicle inspection before departure: Conduct a comprehensive check of the vehicle every day before setting off, including checking for oil or water leaks; measure tire pressure to ensure it is appropriate; inspect the engine oil condition; check if the spare tire is intact, etc. 2. Be cautious when wading: If encountering waterlogged roads, be aware of the water depth and the condition of the road beneath before deciding whether it exceeds the vehicle's capability. Avoid attempting to wade through water deeper than half the height of the car's tires. 3. Obey traffic rules: Especially on highways, do not speed. Speeding not only risks fines from traffic police but, more importantly, is unsafe.
13
5
Share

What is the difference between 1.5L and 2.0L displacement?

1.5L and 2.0L displacement differ in the following aspects: A 2.0L engine has a larger exhaust volume than a 1.5L vehicle. The power output of a 2.0L displacement engine is greater than that of a 1.5L displacement engine. Related explanations: 1. Introduction: Displacement (Swept-volume), a specialized term in hydraulic transmission, refers to the volume of fluid inhaled or discharged per stroke or cycle. Generally, a larger displacement means the engine releases more energy (converting chemical energy from fuel into mechanical energy) per unit time, resulting in better "power performance". 2. Extension: The displacement range for compact cars is typically 1.0L-1.6L, while mid-size cars usually have displacements between 1.6L-2.5L. The fuel consumption of a 2.0L displacement engine is generally higher than that of a 1.5L displacement engine.
8
3
Share

Where is the DCU located in Dongfeng Tianlong?

Dongfeng Tianlong's DCU is located next to the urea tank. Meaning of DCU: DCU stands for Diesel Control Unit, which is the core of electronically controlled fuel injection, commonly known as the engine computer. It is a type of traction control unit. DCU control principle: The Dosing-Control-Unit (DCU) monitors vehicle status in real-time through sensors and precisely controls actuators via software calculations to achieve accurate system control. It can be integrated into Bosch EDC17CV electronic control units.
20
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.