When Should Brake Discs Be Replaced?

1 Answers
DiEverly
07/29/25 6:14pm
Brake discs do not have a definitive replacement interval, as their replacement timing is influenced by the vehicle's operating environment and the driver's habits. Generally, front brake discs should be replaced approximately every 60,000 to 80,000 kilometers, while rear brake discs require replacement around every 100,000 kilometers. Relevant details are as follows: 1. The replacement of brake discs is not determined by usage time or mileage alone; it primarily depends on the driver's habits and the quality of the brake discs themselves, ultimately reflected in the remaining thickness of the brake discs and their radial runout value. 2. Replacing brake discs does not necessarily require replacing the brake pads. If the brake pads still have substantial thickness, they can be retained when replacing the brake discs.
Was this review help?
3
2
Share
More Forum Discussions

How to Replace the Wiper Blades on a Lavida?

The method for replacing the wiper blades on a Lavida is as follows: 1. After turning off the vehicle, do not remove the key immediately. Within 3 seconds, pull the wiper control lever inward, and the wipers will move to the maintenance position. 2. Gently pull the wiper arm toward the front of the vehicle until it locks into place. Press the silver button on the wiper arm, hold the wiper blade, and pull it outward with slight force to remove the old rubber blade. 3. Release the two clips and remove the old rubber blade. 4. When installing the new rubber blade, remember to stagger the two metal pieces and ensure it is inserted into the first groove. The process is slightly tedious and requires patience; install one side first before proceeding to the other. 5. After successful installation, follow the reverse order of the removal steps to complete the wiper blade installation.
20
1
Share

How Hard is Carbon Fiber?

Carbon fiber material is an ultra-hard substance that is 10 times harder than ordinary steel, second only to the hardness of diamond. Below is a relevant introduction to carbon fiber: 1. Composition of Carbon Fiber: Carbon fiber is formed by stacking organic polymer fibers with extremely high carbon content along the fiber bundle direction. The currently recognized high hardness and ultra-strong shear resistance are not entirely due to material properties. There is a decisive factor involved—the critical void. When the stacking between fibers is below a certain critical value, the void index between fibers determines the hardness, shear resistance, and tensile strength of the fiber. 2. Reasons for Hardness Reduction: The critical porosity that causes a decline in material mechanical properties is 1%–4%. When the void volume content is within the range of 0–4%, for every 1% increase in void volume content, the interlaminar shear strength decreases by approximately 7%. Moreover, higher porosity leads to larger void sizes, significantly reducing the area of interlaminar interfaces in the laminate. When the material is under stress, it is prone to failure along the layers, which is why interlaminar shear strength is relatively sensitive to porosity.
8
4
Share

Are Passat Seat Heating and Seat Ventilation the Same?

Passat seat heating and seat ventilation are not the same functions. Seat heating refers to the electric heating device inside the seat. Seat ventilation is the "summer cooling device" of the car seat air conditioning, which is divided into air supply type and air suction type. More details are as follows: 1. The car seat air conditioning system includes ventilation circulation, dehumidification and cooling/heating, and intelligent temperature control, completely eliminating the discomfort caused by the seat being hot and sticky in summer and cold in winter while driving. 2. As an effective supplement to the car air conditioning system, the car seat air conditioning system can adjust the temperature and humidity of the seat surface, maximizing the satisfaction of different drivers and passengers' requirements for seat surface temperature in different seasons, helping them maintain full energy and clear reaction ability. According to statistics, it can save fuel consumption by an average of 7-9%. 3. The car seat air conditioning system is divided into two types: external and built-in. Seat heating uses electric heating wires inside the seat to heat the seat interior and transfers the heat to the occupant through heat conduction, improving the discomfort caused by the seat being too cold after long periods of parking in winter.
13
2
Share

How to use the GAC GS3 navigation system?

GAC GS3 navigation system usage method is as follows: 1. The GAC GS3 center console panel adopts a snap-on design. For complete removal, a pry bar and a Phillips screwdriver are required. 2. Start prying from the bottom of the center console panel. After prying it open, remove the wiring harness and take out the original radio panel. 3. Install the navigation system by connecting the plugs. If unsure, refer to the car navigation manual for guidance. 4. Install the GPS receiving antenna and the rearview camera. 5. Route the rearview camera wiring harness along the door edge seal to the rear seats, then fold down the rear seats and pass it through to the trunk. 6. Install the rearview camera inside the license plate light, then route the camera wiring harness back and complete the installation. 7. Test for any issues. If everything is normal, reinstall in the reverse order of removal.
15
2
Share

What is the battery model for the Buick Encore?

The battery model for the Encore is a Varta 95D31 battery. Here is some relevant information: 1. The lifespan of a car battery is generally around 3 years. If the vehicle has fewer electrical appliances and you pay attention to charging it regularly to keep the battery fully charged, you can effectively extend its service life. 2. When a car battery is not used for a long time, it will slowly discharge on its own until it becomes unusable. Therefore, it is recommended to start the car periodically to recharge the battery. 3. Avoid leaving the car in an open parking lot for extended periods. If the vehicle is to be parked for a long time, the battery should be removed and stored to prevent it from freezing and getting damaged. Additionally, the battery's charge level can be monitored on the dashboard. When the ammeter indicates low charge, the battery should be charged promptly. 4. In winter, car engines are harder to start. Each attempt to start the engine should not exceed 5 seconds, and the interval between subsequent attempts should be at least 15 seconds.
9
3
Share

How many colors does the new Buick Excelle have?

Buick Excelle's color options mainly include Ruby Red, Piano Black, Skyline Blue, Glacier Silver, Titanium Gray, Khaki Gold, Latin Red, China Red, Deep Space Blue, Moonlight Silver, and more. Automobile colors can be divided into basic colors and trendy colors. More details are as follows: 1. Basic colors are essential hues with relatively stable market demand, evolving under the influence of new materials and technologies. Trendy colors belong to fashionable shades that change according to trends. In the sedan segment, the variation of trendy colors is particularly noticeable, catering to diverse demographics. 2. In the Chinese market perception, luxury cars and official vehicles predominantly feature black due to herd mentality and the pursuit of premium product characteristics, resulting in a higher proportion of black cars. 3. However, with the younger demographic's preference for personalization and the maturing automotive market, the concentration of black is diminishing. Different consumers have varied psychological needs that require corresponding colors to satisfy their inner preferences.
18
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.