When does the driving license points get updated?

1 Answers
DanteDella
07/25/25 4:24am
Driving license points are updated every 12 months. Here is relevant information about the C1 driving license: 1. Development: The C1 driving license evolved from the C driving license. In 2004, according to the "Road Traffic Safety Law" and its supporting policies, the older version of the C license (C driving license) held by drivers was automatically converted to a B1 license in the vehicle management office's database. If drivers did not wish to convert, they had to apply to the vehicle management office to downgrade to the new C1 license. Original holders of the C license could convert to B1 (with the additional condition that the driver must be at least 21 years old), C1, or C2. Previously, there was only one type of C license, which was later divided into the C1 license for driving manual transmission "small passenger" vehicles, the C2 license for driving automatic transmission "small passenger" vehicles, as well as the C3 and C4 licenses. Later, the C5 license was added. 2. Driving requirements: According to the "Regulations on the Application and Use of Motor Vehicle Driving Licenses," the C1 driving license permits driving small and micro passenger vehicles, light and micro cargo vehicles, and light, small, and micro special-purpose vehicles. Small passenger vehicles must have a seating capacity of 9 or fewer people. According to this standard, the C1 license does not permit driving vehicles with more than 9 seats.
Was this review help?
16
3
Share
More Forum Discussions

How to Adjust the Time on a Honda City?

Adjusting the time on a Honda City requires completing the process on the car's central console. The specific steps are as follows: 1. Press the function key (MENU) to select the time setting. 2. Use the knob to select the time, setting the hour and minute parameters separately. 3. Press the center setting key (SELECT) to confirm and complete the time adjustment. Below is an introduction to the all-new Honda City: 1. The interior of the all-new City has been upgraded with richer configurations. The interior features a clear and neat layout; it uses the Honda family's three-spoke multifunction steering wheel and mechanical pointer instrument panel, supporting CarPlay functionality, making it highly practical. 2. The all-new City is powered by the latest Earth-Dreams series engine, offering a choice between a 5-speed manual and a CVT continuously variable transmission, providing stronger driving operability. 3. The vehicle has strong fuel economy, with an average fuel consumption of 6-7L per 100 kilometers, making it very fuel-efficient.
19
1
Share

What are the differences between the X-Trail Smart Connect Edition and Comfort Edition?

The main differences between the X-Trail Comfort Edition and Smart Connect Comfort Edition are that the Smart Connect Comfort Edition comes with a larger central control screen, allowing users to download a mobile app to check vehicle status and location, as well as remotely control the vehicle. Remote control functions include remote engine start and remote air conditioning activation. The specific differences (taking the 2019 5-seater models as examples) are: 1. In terms of price, the official guide price of the Comfort Edition is slightly cheaper than that of the Smart Connect Comfort Edition. 2. The Comfort Edition has a 7.0-inch LCD screen, while the Smart Connect Comfort Edition has a 9.0-inch LCD screen. 3. The Smart Connect Comfort Edition includes GPS navigation, voice control, and WIFI connectivity. 4. The Comfort Edition offers smartphone connectivity (including CarPlay and Carlife) and an AUX external interface. Both models are equipped with a 2.0L inline 4-cylinder naturally aspirated engine, paired with a CVT transmission, delivering a maximum power of 113KW and a maximum torque of 204N·m. In terms of dimensions, both have a length/width/height of 4675/1820/1722mm and a wheelbase of 2706mm. Both models feature MacPherson strut front suspension and multi-link independent rear suspension.
10
5
Share

What are the installation steps for an external tire pressure monitoring system?

Installation steps for an external tire pressure monitoring system: 1. Prepare the installation tools, including hex nuts, dust covers, dust washers, cover openers, and nut wrenches; 2. The tire pressure sensor contains a button battery, which typically lasts 2 to 3 years under normal conditions. When the battery of the tire pressure sensor is depleted, the tire pressure display will provide a corresponding alert, and the owner should replace the battery promptly; 3. Remove the dust washer from the tire pressure sensor, then use a nut wrench to unscrew the outer shell, revealing the button battery inside the sensor; 4. The advantage of an external tire pressure monitor is that it does not require tire removal, debugging, or wiring for installation; 5. Unscrew the dust cap from the valve stem, then fit the dust cover, attach the hex nut, install the tire pressure sensor, and tighten the sensor with a nut wrench, completing the installation of one tire pressure sensor; 6. For the first installation, the vehicle needs to be driven at a speed of over 20 km/h before data begins to display. This external tire pressure monitoring device is powered by solar energy, and during the charging process, the display will show a small sun icon; 6. After successful installation on all four wheels, only the tire pressure values are displayed under normal conditions.
10
1
Share

How to Perform a Launch Control Start in an Automatic Transmission Car?

Here are the steps for performing a launch control start in an automatic transmission car (using the BMW M4 as an example): 1. A launch control start puts significantly more strain on the engine and transmission compared to normal driving. Many manufacturers impose a limit on the number of launch control starts allowed, and exceeding this limit may void the warranty for engine or transmission damage. Therefore, it's essential to warm up the car before attempting a launch control start. 2. Turn off the ESP (Electronic Stability Program), which is equivalent to disabling DSC (Dynamic Stability Control) in the BMW M4. 3. Shift the transmission into manual mode to lock it in first gear. This maximizes the torque output from the engine by utilizing the highest gear ratio in first gear, providing the strongest launch torque. 4. Press the brake pedal all the way down, then press the accelerator pedal all the way down. The KICK-DOWN function here is like unlocking the car's full potential—holding the accelerator pedal down activates this mode, signaling the car that you need maximum performance, which in turn activates the launch control function. 5. Use the cruise control to adjust the engine RPM—up to increase, down to decrease—to control the maximum RPM when the accelerator is fully depressed. The peak torque RPM for gasoline engines is not at the highest RPM; this varies depending on the specific model. For the BMW M4, the peak torque RPM is between 3000-3500, so set the cruise control to a maximum of 3500 RPM. 6. Once the engine reaches the set maximum RPM, release the brake immediately, and the car will 'zoom' forward.
18
0
Share

What is the Son of Wind car?

Son of Wind is a supercar under the Pagani brand, known for its extremely high price and rarity. The Son of Wind refers to the Zonda model, which comes in hardtop, convertible, and more powerful track-ready racing versions. Relevant information about Pagani is as follows: 1. Pagani manufactures hypercars, with all its models being limited editions priced over ten million. 2. Pagani currently produces only two models: the Zonda and the Huayra. The Huayra features exceptionally beautiful exterior design, and its interior resembles a work of art.
15
4
Share

How to adjust the timing on an old Passat?

Old Passat timing installation steps are as follows: 1. Align the crankshaft according to the marks on the crankshaft timing pulley, generally requiring the piston to be at top dead center position; 2. Install the camshaft timing pulley and align the marks on the camshaft, with dual camshafts aligning both camshaft positions separately; 3. Install the timing belt/chain properly. 4. Additional information: The main function of the engine timing belt is to drive the engine's valve train, ensuring the engine's intake and exhaust valves open or close at the appropriate times to guarantee normal cylinder intake and exhaust.
14
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.