When can the S gear in an automatic transmission be used?

1 Answers
VonNora
07/30/25 3:22am
Automatic transmission S gear can be used when overtaking, going up or down slopes, and in traffic jams. When overtaking: The S gear can instantly provide high torque, allowing the car to accelerate quickly in a short time. When going up or down slopes: Whether ascending or descending, on steep and long slopes, using the S gear to downshift can utilize engine braking, reducing reliance solely on the brakes and enhancing driving safety. In traffic jams: The S gear can lock the gear in a low position, reducing wear and tear on the transmission caused by frequent gear shifts. The S gear is a sports mode. When switched to S gear, the car's power increases directly, turning into an aggressive mode, which is different from the usual gear. Therefore, prolonged use of the S gear can accelerate the wear of high-speed rotating components inside the engine due to this more aggressive driving mode.
Was this review help?
11
0
Share
More Forum Discussions

What are the body dimensions of the Volkswagen Lavida?

The body dimensions of the Volkswagen Lavida are 4670mm in length, 1806mm in width, and 1474mm in height, with a wheelbase of 2668mm. The Lavida is a compact sedan under the Volkswagen brand, equipped with a 1.5L naturally aspirated engine and a 1.4L turbocharged engine. The 1.5L naturally aspirated engine delivers a maximum power of 85kw and a peak torque of 150nm. The 1.4T turbocharged engine produces a maximum power of 110kw and a peak torque of 250nm. The transmission options paired with the engines include a 5-speed manual, a 6-speed automatic, and a 7-speed dual-clutch transmission.
16
0
Share

What is the engine number of the BYD Tang?

The engine number of the BYD Tang is BYD487ZQA. This engine is a 2.0T turbocharged engine independently developed by BYD, with a vertical integration rate of up to 90% in its production. The BYD487ZQA engine features technologies such as exhaust gas turbocharging, full aluminum alloy construction, dual variable valve timing, direct fuel injection, dual balance shafts, and intercooled intake manifold. The BYD Tang is a mid-size SUV under the BYD brand, available in three different drivetrain configurations: gasoline, plug-in hybrid, and pure electric. Both the gasoline and plug-in hybrid versions offer five-seat and seven-seat variants. All three powertrain options are built on BYD's BNA architecture-based BLP large luxury vehicle platform, sharing similar exterior designs and incorporating BYD's signature Dragon Face design philosophy.
18
5
Share

Where is the crankshaft position sensor located on a Mercedes-Benz E240?

The crankshaft position sensor on a Mercedes-Benz E240 is generally installed on the transmission housing, receiving signals from the flywheel's ring gear. Definition of the speed sensor: It detects engine speed, hence also known as the speed sensor; it detects the top dead center position of the pistons, thus also referred to as the top dead center sensor, including detecting the top dead center signals of each cylinder for ignition control and the first cylinder's top dead center signal for sequential fuel injection control. Working principle and function: The function of the crankshaft position sensor is to determine the position of the crankshaft, i.e., the crankshaft's angle and the engine speed. It usually works in conjunction with the camshaft position sensor to determine the basic ignition timing.
14
3
Share

What to Do When the Engine Radiator Overheats?

Overheating is usually caused by insufficient water in the radiator, leaks, or the radiator fan not working. The solutions are as follows: 1. Immediately find a safe place to park, but do not turn off the engine right away. Let the engine idle to continue cooling down, and open the hood to increase the cooling speed. 2. After some time, check if there is any leakage under the car. 3. Once the temperature gauge needle drops to a suitable level, turn off the engine. 4. Use a wet towel to cover the radiator cap, then slowly open the first switch (about 1/4 turn). After the steam pressure is fully released, completely open the radiator cap. Check the water level and quality in the radiator, as well as whether the fan belt is abnormal. If the water level is insufficient, slowly add water until it reaches near the maximum mark.
10
5
Share

What are the specifications of motorcycle tires?

Example: If the tire specifications of a motorcycle are 205, 65, R17, 92V. The following explains their meanings in detail: 1. 205: The 205 refers to the width of the motorcycle tire, which is 205mm. 2. 65: 65 refers to the aspect ratio of the tire, meaning the section height is 65% of the tire height. 3. R17: R indicates that the tire is a radial tire, and 17 is the rim diameter of the tire in inches. 4. 92V: 92 refers to the load index of the tire, which means 92 multiplied by 4, indicating it can withstand a pressure of 368kg. V refers to the speed rating, indicating it can reach up to 240km/h.
17
5
Share

Is Crystal Coating Harmful to Car Paint?

Crystal coating does not harm car paint. The process involves deep cleaning the paint surface, performing mirror restoration, degreasing the vehicle, and then directly applying the crystal coating. Since new car paint has fewer contaminants and almost no scratches, the procedure is relatively quick for new vehicles. Below is a brief introduction to car crystal coating: 1. For cars that have been used for some time, the paint surface should first be polished, followed by mirror restoration, degreasing, and then crystal coating. 2. Car crystal coating provides reliable paint sealing technology, offering efficient and long-lasting protection to the paint, preventing environmental factors from affecting the paint color. 3. Car crystal coating is entirely different from car film coating, waxing, or glazing. Its base material is SIO2 inorganic substance.
15
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.