What vehicles can a Class C license drive?

1 Answers
Hank
07/24/25 9:58pm
Small and mini passenger vehicles, light and mini trucks, light, small, and mini special operation vehicles. It also allows driving small and mini automatic transmission cars, or light and mini automatic transmission trucks. Below is extended information about Class C licenses: 1. Classification: Class C driver's licenses include C1, C2, C3, C4, and C5. 2. Validity period: Initially, a Class C license is valid for 6 years. If no more than 12 penalty points are accumulated within these 6 years, the license can be renewed for a 10-year validity period upon expiration. Similarly, after the 10-year period ends, it can be renewed for a long-term license.
Was this review help?
9
4
Share
More Forum Discussions

How to Replace the Key Battery for BYD?

The method to replace the key battery for BYD is as follows: 1. Remove the mechanical key; 2. Along the slot where the mechanical key is stored, forcefully pry open the key's outer shell; 3. Use a blade to remove the battery from the edge gap; 4. After installing the new battery, reassemble the key shell. Taking the BYD S6 as an example, it is a mid-size SUV with body dimensions of: length 4810 mm, width 1855 mm, height 1680 mm, a wheelbase of 2720 mm, and a fuel tank capacity of 72 liters. The BYD S6 is equipped with a 1.5L turbocharged engine, delivering a maximum power of 113 kW at 5200 rpm, paired with a 6-speed manual transmission.
15
3
Share

How to Distinguish Between Run-Flat Tires and Regular Tires?

Run-flat tires and regular tires can be distinguished by the following methods: 1. Appearance: Run-flat tires have special markings, while regular tires do not; 2. Structure: The sidewalls of run-flat tires are thicker than those of regular tires; 3. Performance: In addition to the functions of regular tires, run-flat tires can allow the vehicle to travel a certain distance even when the tire pressure is zero. Tire maintenance methods include: 1. Regularly check tire pressure; 2. Regularly check front wheel alignment; 3. Avoid dragging tires on the ground to reduce tread wear; 4. Control speed appropriately based on the gradient, length, and road conditions; 5. Drive according to road conditions.
20
5
Share

Where is the oxygen sensor located?

The oxygen sensor is located on the engine exhaust pipe. It uses a ceramic sensing element to measure the oxygen potential in the vehicle's exhaust pipe, calculates the corresponding oxygen concentration based on the principle of chemical equilibrium, and achieves the purpose of monitoring and controlling the combustion air-fuel ratio to ensure product quality and exhaust emission compliance. The functions of the oxygen sensor are: 1. To determine whether there is excess oxygen in the exhaust after engine combustion and convert the oxygen content into a voltage signal transmitted to the engine computer; 2. To enable the engine to achieve closed-loop control targeting excess air, ensuring that the three-way catalytic converter has high conversion efficiency for pollutants such as hydrocarbons, carbon monoxide, and nitrogen oxides in the exhaust, thereby maximizing the conversion and purification of emission pollutants.
8
4
Share

What to Do When an Automatic Transmission Car Runs Out of Battery?

The solution for an automatic transmission car running out of battery is: find a car that can start normally, position the two cars facing each other, open the hood and take out the jumper cables, connect positive to positive and negative to negative to charge. Reasons for an automatic transmission car running out of battery: 1. Battery is dead; 2. Spark plug failure; 3. Fuel filter failure; 4. Circuit failure; 5. Mechanical failure; 6. Severe engine carbon buildup. Methods to prevent an automatic transmission car from running out of battery: 1. Do not park the car in an open parking lot for a long time; 2. Avoid multiple uninterrupted starts of the vehicle; 3. Regularly check the battery accessories and connecting circuits; 4. Do not use car electronics after the car is turned off.
20
5
Share

What to Do If Wheel Balancing Was Not Performed After Tire Repair?

The solution for not performing wheel balancing after tire repair is: to redo the wheel balancing test to prevent abnormal wheel vibrations during high-speed driving. Wheel balancing is a process that corrects the balance of the wheel edges by adding counterweights while the wheel is in motion, ensuring the wheel remains balanced during rotation. The steps for performing wheel balancing are: 1. Remove the original counterweights before starting the balancing process; 2. Use a specialized wheel balancing machine to measure the weight distribution of the wheel; 3. Add counterweights of appropriate weight at the corresponding positions. Situations that require wheel balancing include: 1. After installing new tires or repairing collision damage; 2. Uneven wear on one side of the front or rear tires; 3. The steering wheel feels excessively heavy or shakes while driving; 4. The car pulls to the left or right when driving straight.
8
1
Share

How to adjust the time on a Volkswagen Polo?

To adjust the time on a Volkswagen Polo, follow these steps: 1. Press the down button on the right side of the steering wheel and select the clock option; 2. Press the OK button to enter the clock setting page; 3. Use the OK button and down button in the same way to enter the hour setting page - each press of the down button advances the hour by one, then press OK to confirm the hour; 4. Adjust the minutes using the same method as adjusting the hours. The Volkswagen Polo is a compact car with body dimensions of: length 4053 mm, width 1740 mm, height 1449 mm, wheelbase 2564 mm, and a fuel tank capacity of 42.5 liters.
5
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.