What type of oil is used in rotary vane vacuum pumps?

1 Answers
VanEvangeline
07/28/25 7:45pm
Introduction to oil for rotary vane vacuum pumps: 1. General conditions: For applications requiring a total pressure above 6X10-2 Pa, high-speed vacuum pump oil produced in Shanghai is recommended. For small pumps below 4L/s, No.1 vacuum pump oil can be used as a substitute. For direct-drive pumps above 8L/s, No.3 diffusion pump oil can be used as an alternative. 2. If the vacuum requirement is not high: and oil contamination and replacement are frequent, or vacuum pump oil supply is difficult, No.50 mechanical oil can be used as a substitute. 3. If the ambient temperature is low: and starting is difficult with no high requirement for ultimate vacuum, vacuum pump oil or mechanical oil with slightly lower viscosity can be used.
Was this review help?
15
1
Share
More Forum Discussions

What are the differences between A-segment and B-segment cars?

The differences between A-segment and B-segment cars are introduced as follows: 1. Different wheelbase: The wheelbase of A00-segment cars is between 2.0 meters and 2.3 meters, A0-segment cars between 2.3 meters and 2.5 meters, and A-segment cars between 2.5 meters and 2.7 meters. Therefore, the wheelbase of A-segment cars should range from 2.0 meters to 2.7 meters. In contrast, B-segment cars have a wheelbase ranging from 2.6 meters to 2.9 meters. 2. Different body dimensions: The body length of A00-segment cars is under 4 meters, A0-segment cars between 4 meters and 4.3 meters, and A-segment cars between 4.2 meters and 4.6 meters. Meanwhile, B-segment cars have a body length ranging from 4.5 meters to 4.9 meters. 3. Different engine displacement: A00-segment cars have a displacement of around 1 liter, A0-segment cars between 1.0 liter and 1.5 liters, and A-segment cars between 1.6 liters and 2.0 liters. B-segment cars, on the other hand, have a displacement ranging from 1.8 liters to 2.4 liters. However, this displacement is just a reference, especially under the development trends of vehicle miniaturization, lightweighting, and turbocharged engines. Many mid-size cars now use 1.4T or 1.5T turbocharged engines, making it difficult to distinguish between A-segment and B-segment cars based solely on displacement.
4
0
Share

What Octane Gasoline Should a Sagitar Use?

Volkswagen Sagitar should use 95 octane gasoline, as this fuel grade is recommended in the vehicle's official user manual. In addition to checking the appropriate gasoline grade in the user manual, you can also find it on the fuel tank cap, which will be clearly marked. Generally, the gasoline grade can also be determined based on the engine's compression ratio. Vehicles with an engine compression ratio between 8.6-9.9 should use 92 octane gasoline, while those with a compression ratio between 10.0-11.5 should use 95 octane gasoline. If the compression ratio is higher, 98 octane gasoline is recommended. However, with the application of new technologies, the compression ratio alone cannot determine the gasoline grade, as high compression ratios can also be tuned to use lower octane gasoline. Other factors, such as ignition timing, turbocharging technology, and Atkinson cycle technology, also play a role. Generally, the higher the gasoline octane number, the higher the octane value and the better the anti-knock performance. 92 octane gasoline contains 92% isooctane and 8% n-heptane, while 95 octane gasoline contains 95% isooctane and 5% n-heptane. If you occasionally use the wrong gasoline grade in a Volkswagen Sagitar, simply switch back to the correct grade after the current tank is used up. However, long-term use of the wrong gasoline grade can have the following effects: For vehicles recommended to use lower octane gasoline, using a higher octane grade will not cause damage, but the increased octane value can alter the fuel's ignition point, leading to delayed combustion in the engine. This reduces the engine's power output and thermal efficiency, resulting in poorer performance. For vehicles recommended to use higher octane gasoline, using a lower octane grade can cause engine knocking. Due to the significantly lower octane value, the gasoline's ignition point decreases, causing premature ignition during the compression stroke. If the fuel ignites before the spark plug fires, resistance occurs during the upward stroke. This resistance makes the engine run very unstably. If the knocking is mild, it may only increase noise without significant engine damage. However, noticeable knocking indicates severe engine conditions, affecting not only driving stability but also causing abnormal wear on pistons and cylinders, potentially leading to cylinder scoring in severe cases.
13
2
Share

Are Tire Pressure Sensors Universal?

Tire pressure sensors are not universal, as different brands of sensors may operate on different transmission frequencies. A sensor is a detection device that can sense the measured information and convert it into electrical signals or other required forms of information output according to certain rules, to meet the requirements of information transmission, processing, storage, display, recording, and control. Tire pressure monitoring systems can be divided into: 1. Indirect tire pressure monitoring systems, which determine tire abnormalities by detecting differences in tire rotation speed; 2. Direct tire pressure monitoring systems, which involve installing four tire pressure monitoring sensors inside the tires.
5
4
Share

What does mid-cycle facelift mean?

Mid-cycle facelift refers to some modifications made to a car's exterior design, enhancing its recognition through detail changes while also providing consumers with a fresh visual experience. Essentially, a mid-cycle facelift aims to keep up with automotive trends and narrow the gap with newer models by implementing certain updates. Vehicle updates are typically divided into three stages: initial, mid-cycle, and major. Initial updates primarily address issues that arise after a new car's launch, most of which are essential fixes based on accumulated experience over time. Major updates refer to comprehensive redesigns, during which higher-end models may be introduced, with optimizations to both exterior and interior designs.
7
3
Share

What is the maximum wading depth of the BMW X3?

The official maximum wading depth of the BMW X3 is 400mm. Here are some precautions regarding water ingress in the BMW X3: Vehicle balance: When driving into water, try to maintain vehicle balance as much as possible to avoid splashing water onto electrical components or allowing water to enter the engine's intake system. Avoid sudden acceleration: Rapidly increasing engine load in a short time may cause water droplets to be sucked in due to the sudden increase in air intake. If you notice wheel slippage or sinking, remember not to accelerate abruptly. Instead, keep the engine running and seek assistance from manpower or other vehicles to drive out of the water channel.
8
0
Share

Why are used Audi Q7 cars so cheap?

Because the Audi Q7 has a very low resale value in the used car market, its price is quite cheap. Here are the specific details regarding this: Factors affecting resale value: Resale value is determined by many factors, including brand, model, market share, quality reliability, price fluctuation range, parts cost, and maintenance convenience, all of which influence the resale value. Q7 resale value: The resale rates for the first five years of the Audi Q7, a luxury SUV, are 67%, 60%, 53%, 46%, and 38% respectively. It can be seen that the Q7's resale value decreases year by year with the age of the car.
3
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.