What type of oil does the Verna use?

What to Pay Attention to When Driving on Flooded Roads in Ningbo

Precautions for driving on flooded roads in Ningbo: Observe the water depth: When the water depth is below half of the wheel, pass through using a low gear with high RPM. If the water level approaches half of the car's tire height, it is not recommended to drive. If the wading depth exceeds the hood, immediately turn off the engine, exit the vehicle, and push it to the roadside. Solutions when wading: When multiple vehicles are wading, do not enter the water simultaneously. Wait for the preceding vehicle to reach the opposite side before the following vehicle enters the water to prevent the preceding vehicle from stopping due to a malfunction, forcing the following vehicle to stop in the water. Avoid driving at high speeds; instead, pass through slowly using high RPM and low gear. Even in shallow water sections, it is best not to drive too fast, as water splashing into the engine compartment can damage the electrical system. If the engine stalls, do not attempt to restart it.

2

5

Share

Should I Replace the Hubcaps on a Base Model Sylphy?

The hubcaps on a base model Sylphy generally do not need to be replaced unless they are bent, cracked, or severely corroded. The base model Sylphy comes with steel hubcaps, which are durable and resistant to minor impacts due to their high strength and good toughness. Therefore, replacement is usually unnecessary. Additional Information: 1. Aluminum Alloy Hubcaps: Most family cars on the market use aluminum alloy hubcaps, which are lighter than steel hubcaps, offer better heat dissipation, and can extend tire life. Additionally, aluminum alloy hubcaps absorb energy more effectively, improving ride smoothness. 2. Steel Hubcaps: The advantages of steel hubcaps include low cost, high strength, and good toughness. However, they have poor heat dissipation, are heavier, which affects vehicle agility, and their limited design options are often a drawback for consumers.

5

1

Share

How to Tell If the Car Battery Is Dead

Methods to check the battery power: 1. Feel the feedback when starting the car. If it feels particularly difficult to start, it is likely due to a weak battery; 2. Battery warning light. If this light stays on, it indicates that the car battery is about to run out of power and needs to be charged promptly; 3. Press the car horn directly. If the horn is not as loud as before, it is likely caused by a weak battery. Car charging precautions: 1. Some cars cannot be completely powered off. Therefore, if using a charger to charge, connect directly to the battery without removing it, otherwise data loss may occur, requiring initialization, commonly known as decoding or code matching; 2. If the battery voltage is 10% lower than the rated voltage, i.e., below 10.8 volts, the battery is at risk of being weak and should be fully charged once a month.

14

2

Share

What Transmission Does the BYD F3 Use?

The transmission used in the BYD F3 is manufactured by Japan's Jatco. Established in 1943, Jatco is one of the world's top three automatic transmission suppliers, with operations spanning Europe, Asia, and the Americas. It primarily supplies automatic transmissions to mainstream automakers such as Nissan, Mitsubishi, Mazda, BMW, Volkswagen, Land Rover, Jaguar, Kia, Hyundai, Daewoo, Changan Ford, and Brilliance. The BYD F3 is equipped with a 5-speed manual transmission. A manual transmission is a gear-shifting device that alters the engine's speed and torque delivered to the drive wheels, enabling the vehicle to achieve varying traction and speed under different conditions such as starting, climbing hills, turning, and accelerating. For the BYD F3's transmission, the following points should be noted during daily use: Do not delay transmission oil changes for extended periods. Prolonged neglect can damage internal components like bearings and the housing. Avoid prolonged coasting in neutral. While some experienced drivers may coast in neutral with manual transmissions, doing so in an automatic can cause overheating and jarring when shifting back to Drive (D). Never engage Drive (D) or Reverse (R) before the vehicle comes to a complete stop. Some drivers shift prematurely to demonstrate smooth operation, but this harms transmission gears and may lead to grinding or other failures over time. Avoid frequent uphill climbs in Drive (D). On steep slopes, automatic transmissions may overheat due to high loads or upshift too early, reducing climbing power. Use manual mode to lock in lower gears or sport mode to protect the transmission. Do not tow over long distances. If the automatic vehicle breaks down, use a flatbed tow truck with the transmission in Neutral (N). Never tow directly with a rope or similar method.

8

4

Share

What does 88V on a tire mean?

88V on a tire refers to the load index and speed rating. The number 88 indicates the load index, while the letter V represents the speed rating. The main functions of tires include: 1. Supporting the entire weight of the vehicle, bearing the load of the car, and transmitting forces and moments in other directions; 2. Transmitting traction and braking torque to ensure good adhesion between the wheels and the road surface, thereby improving the car's power performance, braking performance, and off-road capability; 3. Working together with the car's suspension system to cushion the impact during driving and dampen the resulting vibrations; 4. Protecting the car's components from severe vibrations, adapting to the vehicle's high-speed performance, reducing driving noise, and ensuring driving safety, handling stability, comfort, and fuel efficiency.

6

5

Share

What is the maximum speed limit for driving on curves?

The maximum speed when driving on curves should not exceed 30 km/h. Turning path: Outside-inside-outside. Try to turn with a large arc that tends to be straight. Turning principles: Slow in, moderate throttle, fast out. Before entering the curve while still driving straight, you should first apply the brakes to slow down the car. If the curve is large, you should further reduce the speed and downshift one gear. Uphill curves: When navigating an uphill curve, release the throttle before entering the curve, allowing the vehicle to enter the curve at a relatively high speed along the outside. Then downshift one or two gears, choose your path and adjust direction while applying light throttle. After passing the apex of the curve, move back to the outside of the curve while increasing throttle, and finally exit the curve quickly along the outside.

17

0

Share

What type of oil does the Verna use?

What to Pay Attention to When Driving on Flooded Roads in Ningbo

Should I Replace the Hubcaps on a Base Model Sylphy?

How to Tell If the Car Battery Is Dead

What Transmission Does the BYD F3 Use?

What does 88V on a tire mean?

What is the maximum speed limit for driving on curves?

Can the Kawasaki Z900 carry a passenger?

What is the recommended speed for a new car during the break-in period?

What to Do When a Mercedes Key is Locked in the Trunk?

How to Use the Lynk & Co 06 Dash Cam?