What type of engine oil should a Jetta use?

1 Answers
FranciscoLynn
07/29/25 6:33pm
Jetta uses engine oil with the specification VW50200, and you can also use 5W-40 or higher grade oil. Here is the method to check the engine oil level: 1. Pull the oil dipstick out of the tube and wipe off the oil marks on the dipstick with a clean cloth; 2. Insert the oil dipstick back into the tube, pushing it in as far as it will go. If there is a mark on the oil dipstick, this mark must align with the groove at the top of the tube after insertion; 3. Pull out the oil dipstick again and read the engine oil level (the level should be between max and min). If there is a slight shortage, you can add an appropriate amount of oil. If there is an excessive amount, visit a service center as soon as possible to determine the cause; 4. After reading the oil level, insert the oil dipstick back into the tube and push it in as far as it will go.
Was this review help?
9
0
Share
More Forum Discussions

How to Deal with Squeaky Brakes on a Vios?

The solutions for squeaky brakes on a Vios are: 1. Replace the brake pads; 2. Replace the brake discs; 3. Clean the brake discs; 4. Clean the brake calipers; 5. Top up the brake fluid. Taking the Vios 2021 model as an example, its body dimensions are: length 4435mm, width 1700mm, height 1490mm, wheelbase 2550mm, minimum ground clearance 160mm, and fuel tank capacity 42l. The Vios 2021 model is equipped with a 1.5l naturally aspirated engine, with a maximum power of 81kw and a maximum torque of 138nm, paired with a 5-speed manual transmission.
15
4
Share

What car has a logo resembling a galloping horse?

The car with a logo resembling a galloping horse is the Ford Mustang. Taking the 2020 Ford Mustang as an example, it is a 2-door, 4-seater hardtop sports car with the following dimensions: length 4794mm, width 1916mm, height 1391mm, and a wheelbase of 2720mm. The fuel tank capacity is 58.9 liters. The 2020 Ford Mustang is equipped with a 2.3L turbocharged engine, delivering a maximum power of 220kW and a maximum torque of 434Nm. It is paired with a 10-speed automatic transmission. The front suspension uses a MacPherson strut independent suspension, while the rear suspension employs a multi-link independent suspension.
12
2
Share

Where is the OBD interface of Dongfeng 330 located?

The OBD interface of Dongfeng 330 is located behind the glove compartment on the passenger side. You can access it by removing the glove compartment. Below is a detailed introduction about the OBD system of Dongfeng 330: 1. OBD stands for On-Board Diagnostics, which is a system that continuously monitors the engine's operating conditions and the working status of the exhaust after-treatment system. If it detects any condition that may lead to excessive emissions, it will immediately issue a warning. 2. When a fault occurs in the system, the OBD system stores the fault information in memory. This information can be read in the form of fault codes using standard diagnostic tools and interfaces. Based on the fault codes, maintenance personnel can quickly and accurately identify the nature and location of the fault. 3. The OBD interface can provide various operational data of the vehicle.
20
2
Share

Is it necessary to apply film to the front windshield of a car?

Applying film to the front windshield of a car: It is necessary. Here is a relevant introduction to the functions of applying film to the front windshield: 1. Heat insulation and sun protection: The film can effectively block a large amount of heat generated by infrared rays. 2. UV protection: Medium and long waves of ultraviolet rays can penetrate thick glass, but applying heat-insulating film can block most UV rays, preventing skin damage and slowing down the aging of car interiors. 3. Safety and explosion-proof: The base layer of car film is polyester film, which has excellent tear resistance and penetration prevention functions. Combined with the adhesive layer of the film, the strength of the glass after applying the film can prevent injuries to passengers caused by accidental glass breakage.
6
0
Share

How Does an Automatic Transmission Work in a Car?

Automatic transmission in a car operates by utilizing planetary gear sets to change gears automatically based on the throttle pedal position and vehicle speed. The transmission, also known as a gearbox, is a mechanism designed to alter the speed and torque from the engine, either maintaining a fixed ratio or changing the gear ratio between the output and input shafts. The functions of a transmission include: 1. Changing the gear ratio to expand the range of torque and speed variations for the driving wheels; 2. Enabling the vehicle to reverse while maintaining the engine's rotational direction; 3. Utilizing neutral gear to interrupt power transmission, allowing the engine to start, idle, and facilitating gear shifts or power output.
5
4
Share

How to reset the tire pressure light on Baojun 510?

To reset the tire pressure light on Baojun 510: 1. Depress the brake pedal; 2. Press the one-touch start button; 3. The instrument panel will illuminate, indicating full vehicle power is activated; 4. Inflate all four tires to standard pressure; 5. Press and hold the tire pressure reset button located below the cigarette lighter for 3 seconds to clear the warning light. Taking the Baojun 510 2021 model as an example, it features a 5-door, 5-seat SUV body structure with dimensions: length 4220mm, width 1740mm, height 1615mm, wheelbase 2550mm, fuel tank capacity 45L, and trunk capacity ranging from 318L to 1210L.
11
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.