What type of engine oil is suitable for the 2018 Vision?

How Much Engine Oil Should Be Added During Maintenance?

For small-displacement vehicles, approximately 3.2 to 3.6 liters of engine oil should be added during each maintenance, while larger-displacement vehicles require around 4.5 liters. Below is expanded information about engine oil: 1. Engine oil is extremely important for engine operation as it performs two major functions: lubrication and heat dissipation. 2. Excessive oil can increase the rotational resistance of the crankshaft, reduce engine output power, and cause the excess oil to enter the combustion chamber, leading to oil burning, blue smoke emission, and increased fuel consumption. 3. The residue from burned oil can accumulate on the walls of the combustion chamber, reducing its space and thereby lowering the engine's compression ratio. It can also accelerate wear on the cylinders and pistons, shortening the vehicle's lifespan. 4. When adding lubricating oil, it is advisable to keep the oil level slightly below the mark on the dipstick. Additionally, factors such as oil type, season, climate, engine displacement, and technical performance should be considered. 5. It is best to choose a professional automotive maintenance center where experts can carefully assess the vehicle, select the appropriate oil, and perform maintenance procedures meticulously to prevent potential faults.

8

5

Share

How to Align the Timing Belt on a Santana?

The method for aligning the timing belt on a Santana is as follows: 1. Ensure that the No. 1 piston is at the top dead center of the compression stroke, the camshaft timing marks are aligned with the marks on the timing belt cover, and the crankshaft sprocket timing mark is aligned with the mark on the oil pump housing. 2. Install the timing belt onto the crankshaft sprocket, then route it past the left camshaft sprocket to the right camshaft sprocket. Ensure the old belt is installed in its original rotation direction, and the letters on the new belt can be read from the rear of the engine. 3. Loosen the timing belt tensioner nut, lift and support the vehicle, install the intermediate timing belt cover, ensure the crankshaft sensor wiring harness is correctly routed, install the lower timing belt cover, and install the crankshaft damper. 4. Rotate the crankshaft clockwise approximately two turns until the yellow mark on the crankshaft damper aligns with the 0 mark on the lower timing belt cover. Remove the plastic access door on the lower timing belt cover, tighten the timing belt tensioner nut to the specified torque, and install the plastic access door. 5. Rotate the crankshaft clockwise 60 degrees until the white mark on the crankshaft damper aligns with the 0 mark on the lower timing belt cover. Ensure the camshaft timing marks are aligned with the marks on the timing cover, and install the remaining components in the reverse order of removal.

18

0

Share

How many points will be deducted for a 7-seater car carrying 9 people?

A 7-seater car carrying 9 people is considered overloading behavior and will result in a penalty of 6 points. Driving a commercial passenger vehicle with more than 20% over the approved capacity will result in 12 points deducted at once; driving a commercial passenger vehicle with less than 20% over the approved capacity, or driving other passenger vehicles with more than 20% over the approved capacity, will result in 6 points deducted at once. Driving passenger vehicles other than commercial passenger vehicles and school buses with less than 20% over the approved capacity will result in 3 points deducted at once. Hazards of overloading: Vehicle overloading severely damages road infrastructure. Since the load of overloaded vehicles far exceeds the design load of roads and bridges, it leads to pavement damage, bridge fractures, and significantly shortens the service life. Overloaded vehicles have increased mass and inertia, longer braking distances, and higher risks. Severe overloading may cause tire blowouts, sudden deviation, brake failure, rollovers, and other accidents due to excessive tire load and deformation. Additionally, overloading affects the vehicle's steering performance, making it prone to accidents due to loss of steering control. Drivers operating overloaded vehicles often experience increased psychological stress and mental pressure, leading to operational errors, affecting driving safety, and causing traffic accidents. Overloaded vehicles cannot maintain normal speeds, occupying lanes for extended periods, directly affecting road traffic flow.

3

5

Share

What to Do When There's Oil on the Spark Plug?

If there is oil on the spark plug, it needs to be replaced with a new one. Steps to replace the spark plug: Open the hood, lift the plastic cover of the engine, remove the high-voltage ignition wires, and mark each cylinder's position to avoid confusion. Use a spark plug socket to remove the spark plugs one by one. While removing them, check for external debris like leaves or dust and ensure everything is cleaned thoroughly. Place the new spark plug into the spark plug hole, hand-tighten it a few turns, and then use the socket to tighten it further. Reinstall the high-voltage ignition wires according to the firing order, and secure the cover. Methods to determine if the spark plug is damaged: Remove the spark plug and observe its appearance. A normal spark plug's insulator skirt and electrodes should appear gray-white, gray-yellow, or light brown. A properly functioning spark plug will have a reddish-brown insulator skirt, with an electrode gap between 0.8-0.9mm and no signs of electrode burn. If the spark plug is contaminated with oil or deposits but not damaged, it can continue to be used after cleaning off the oil and deposits. If the spark plug is severely damaged, showing signs like blistering, black streaks, cracks, or melted electrodes, the cause of the damage should be identified. After troubleshooting, replace the spark plug with a new one. Additionally, if the spark plug appears black as if smoked, it indicates the wrong heat range was selected or the air-fuel mixture is too rich, causing oil to rise.

15

4

Share

What causes high engine temperature in Ford Focus?

High engine temperature in Ford Focus is generally caused by a malfunctioning temperature controller, issues with the thermostat, or blockages in the cooling circulation system. Below are relevant details: 1. Ford: Ford is a world-renowned automobile brand, one of the many brands under the American Ford Motor Company. The company and brand name "Ford" originates from the surname of its founder, Henry Ford. 2. Notes: High engine temperature is a normal phenomenon as long as the engine coolant is sufficient.

12

3

Share

Does the 2016 Qashqai have ESP?

Qashqai 2016 comes standard with ESP across all models. Here is an introduction to the ESP system: 1. Maintains vehicle stability: ESP, or Electronic Stability Program, helps the vehicle maintain optimal stability under various conditions, with particularly noticeable effects in cases of oversteering or understeering. 2. Related control: ESP primarily controls the longitudinal and lateral stability of the vehicle, ensuring it follows the driver's intended path. 3. Function: When the tires are about to lock up during braking, the Electronic Stability Program performs high-frequency braking in the form of mechanical point braking within one second, allowing the vehicle to maintain steering control via the steering wheel even during full braking.

14

2

Share

What type of engine oil is suitable for the 2018 Vision?

How Much Engine Oil Should Be Added During Maintenance?

How to Align the Timing Belt on a Santana?

How many points will be deducted for a 7-seater car carrying 9 people?

What to Do When There's Oil on the Spark Plug?

What causes high engine temperature in Ford Focus?

Does the 2016 Qashqai have ESP?

What is a CRD car?

How to reset the oil check reminder on Audi A3?

What happens if a diesel car is filled with 92 gasoline?

Where is the fuel filler switch of Wuling Hongguang?