What transmission does the Tiida use?

1 Answers
SanElle
07/29/25 8:03pm
Tiida uses a 5-speed manual transmission and a CVT transmission. The functions of the transmission are: 1. To change the transmission ratio, expand the range of torque and speed variation of the driving wheels, and allow the engine to operate under favorable conditions; 2. To enable the car to reverse while keeping the engine rotation direction unchanged; 3. To use neutral gear to interrupt power transmission, allowing the engine to start and idle, facilitating gear shifting or power output. Taking the 2020 Tiida as an example, it belongs to the compact SUV category, with body dimensions of: length 4393mm, width 1766mm, height 1539mm, a wheelbase of 2860mm, a minimum ground clearance of 173mm, and a fuel tank capacity of 52 liters.
Was this review help?
2
3
Share
More Forum Discussions

How many liters of transmission oil should be added to the Peugeot 308 manual transmission?

Peugeot 308 requires approximately 2 liters of transmission oil for replacement. Relevant information is introduced as follows: 1. Peugeot 308 is a compact car: The first Peugeot 308 model is equipped with a 120 horsepower 1.6L inline 4-cylinder gasoline engine transplanted from the 207 model, fitted with 215/55R16 Michelin tires. 2. Automatic transmission oil: Generally, it should be replaced every 120,000 kilometers under normal driving conditions, and every 60,000 kilometers under severe driving conditions. 3. Classification of transmissions: Divided into manual and automatic types. Manual transmissions mainly consist of gears and shafts, achieving speed and torque variation through different gear combinations; while automatic transmissions (AT) are composed of hydraulic torque converters, hydraulic torque variation systems, and hydraulic control systems, achieving speed and torque variation through hydraulic transmission and gear combinations.
3
1
Share

How to Adjust the Time on a Wuling Hongguang Vehicle?

The steps to adjust the time on a Wuling Hongguang are: 1. Ignite the vehicle, at which point the time will be displayed on the radio in the center console; 2. Press and hold the button labeled 'h' until the clock on the radio starts blinking, then rotate the central power button left or right to adjust the hour; 3. After setting the hour, adjust the minutes by pressing and holding the button labeled 'm' until the minutes start blinking, then rotate the central power button left or right to set the minutes. Taking the 2020 Wuling Hongguang S as an example, its body dimensions are: length 4390mm, width 1660mm, height 1750mm, with a wheelbase of 2720mm and a body weight of 1185kg.
4
5
Share

Should a New Car Be Equipped with an Engine Guard Plate?

Should a new car be equipped with an engine guard plate? An engine guard plate is generally installed under the chassis at the front of the car to prevent the engine from being bumped. The types of car engine guard plates include: 1. Iron guard plate; 2. Aluminum alloy guard plate; 3. Plastic-steel guard plate; 4. Plastic guard plate. The reasons for installing an engine guard plate are: 1. The engine is one of the core components of a car. Installing a guard plate on its exterior can block the impact force caused by flying stones hitting the engine when driving over uneven road sections; 2. During vehicle use, a lot of mud or dust may be encountered. Driving in rainy weather can easily corrode the car's chassis. Installing an engine guard plate can provide better protection for the engine and the guard plate itself.
14
1
Share

Where is the Focus radio fuse located?

The fuse for the Focus radio is located on the rear side of the glove compartment on the passenger side. Below are specific details about the fuse: 1. Function: The fuse box is an overcurrent protection switch, primarily used to control circuit operation. There are many circuits in a car, and fuses serve to protect these circuits. When the circuit temperature is too high or the current is excessive, the fuse will blow to protect the circuit. 2. Impact of Blowing: The car fuse box contains many fuses and relays. When a fuse blows, certain functions of the car may be affected. After a fuse blows, it needs to be replaced with a new one. 3. Replacement Notes: When replacing a fuse, use a specialized tool to remove the fuse. The fuse box in the engine compartment is generally located near the battery, while the fuse box in the cabin is usually located near the driver's position or inside the passenger glove compartment.
10
2
Share

Do You Need to Press the Brake When Shifting from N to D Gear?

Shifting from N to D gear does not require pressing the brake, and switching between other driving gears also does not require pressing the brake. Situations where an automatic transmission car requires pressing the brake: 1. Shifting from P gear to other gears requires pressing the brake; 2. Shifting from N gear to D or R gear requires pressing the brake. Precautions for shifting gears in an automatic transmission car: 1. Ensure the gear is in N or P before starting the engine, and remember to press the brake when starting; 2. Gear shifting should be timely, accurate, decisive, and quick, avoiding any delay; 3. Upshift after accelerating, downshift after decelerating; 4. Use D gear when driving on flat and straight roads; 5. Shifting between N, D, and 3 gears does not require pressing the shift button.
8
5
Share

What is the purpose of cleaning the throttle body?

The purpose of cleaning the throttle body is to ensure smooth air intake, restore the vehicle's idle speed and emissions, and regain the vehicle's power. The throttle body's function is to control the air entering the engine. After the air enters the intake pipe, it mixes with gasoline to form a combustible mixture, which then burns to generate power. Effects of a clogged throttle body: 1. The vehicle may experience idle speed fluctuations, and cold starts may become difficult; 2. The engine may stall easily after rapid acceleration and sudden throttle release; 3. Increased fuel consumption and engine vibrations may occur. The method for cleaning carbon deposits inside the throttle body is as follows: 1. Remove the intake hose to expose the throttle body; 2. Disconnect the negative terminal of the battery and turn off the ignition switch; 3. Straighten the throttle plate and spray a small amount of carburetor cleaner into the throttle body; 4. Wipe clean using a polyester cloth or high-density non-woven fabric.
5
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.