What to Do When Your Driver's License Points Reach 12?

1 Answers
LeonardoLynn
07/29/25 11:30pm
If your driver's license points reach 12, your license will be temporarily suspended, and you won't be able to drive on the road. Your legal driving rights will only be restored after the demerit point cycle ends. Below is some relevant information about vehicle violations: 1. Notification method: After a violation, you will usually receive a text message or letter notification, instructing you to go to the specified location within the given time to handle the violation. The ways to handle violations are either online or at the vehicle management office. 2. Online processing has certain limitations: It is only applicable to violations with fines not exceeding 200 yuan; the violation points do not reach 12 after deduction; and the violation is not a result of on-site law enforcement.
Was this review help?
14
0
Share
More Forum Discussions

How to reset the tire pressure of Haval H2?

Haval H2 tire pressure reset method: When the tire pressure light is on and needs to be reset, if the tire pressure sensor has not been replaced, the tire pressure light will automatically turn off after driving a certain distance; if the tire pressure sensor has been replaced, you need to go to a 4S shop and use a special computer for matching. Tire pressure refers to the air pressure inside the tire. In terms of car maintenance, if the engine is the heart of the car, then the tire pressure is the blood pressure of the car. The level of tire pressure plays a crucial role in the performance and power of the car. The Haval H2 is a compact SUV launched by the Haval brand under Great Wall Motors. The length, width, and height of this car are 4335mm, 1814mm, and 1695mm respectively, with a wheelbase of 2560mm. The Haval H2 adopts a new power combination of Great Wall's self-developed 1.5T high-efficiency and energy-saving engine and Getrag wet 7DCT transmission, and the automatic transmission model comes standard with an engine intelligent start-stop system.
3
3
Share

How to Reset the Low Tire Pressure Warning in a Car?

The method to reset the low tire pressure warning in a car is: 1. Park on a level road, turn off the engine, and then power on the vehicle; 2. Press and hold the tire pressure monitoring button for about 5 to 6 seconds until you hear an alarm sound; 3. Release the button, and the tire pressure will be reset. The methods to address the low tire pressure warning are: 1. Inflate the tires to the correct pressure; 2. Check for any air leaks in the tires; 3. Inspect the tires for any deformation. The reasons for the low tire pressure warning are: 1. Slow air leakage from the tire; 2. The tire is flat; 3. There is a gap between the tire and the wheel rim. The effects of low tire pressure are: 1. Increased friction coefficient with the road surface; 2. Heavy steering wheel and a tendency to drift, which are unfavorable for driving safety; 3. Increased movement in various parts of the tire, leading to excessive rolling and abnormal heat generation in the tire.
18
5
Share

What is the wading depth of the Qiao Ge i?

The Qiao Ge i does not have a specific wading depth data, but it can briefly exceed the engine side cover, but not the air filter. Below is the relevant introduction: Definition of maximum wading depth: The maximum wading depth refers to the distance between the tire contact point and the engine air intake, known as Wattiefe in English. The maximum wading depth is the greatest depth that can be safely traversed under safe driving conditions, also referred to as the safe depth. It is an important indicator for evaluating a vehicle's off-road capability; the greater the maximum wading depth, the stronger its wading ability. Factors determining wading depth: A vehicle's wading depth is determined by the height of the vehicle's chassis, which is listed as "ground clearance" in the model's parameter configuration table (some models may provide "maximum wading depth"). The greater the ground clearance, the higher the chassis, and the safer the vehicle is when passing through waterlogged roads.
9
0
Share

How to Apply Window Tint Film to Car Glass?

Steps for applying window tint film to car glass: 1. To avoid dust and impurities affecting the tinting effect, the first step is to thoroughly clean the car's glass before applying the film; 2. Areas that may be damaged during the tinting process should be covered in advance to prevent scratches on the car paint, interior, etc. Any accessories that might interfere with the installation should also be removed beforehand; 3. Cut the tint film according to the size of the glass for an initial fit; 4. Apply the roughly cut film to the car glass, then heat-shrink the film for the front and rear windshields to match the curvature of the glass. This ensures the film adheres smoothly to the glass without water marks; 5. After heating, the film will fit snugly on the glass. At this point, fine-tune the film by precisely cutting it to match the shape of the glass; 6. Window tint film is applied to the inside of the glass, so a crucial step is the final application. The interior side of the glass must be cleaned thoroughly, and the film must be applied quickly and accurately, with any moisture promptly smoothed out; 7. After completing the tinting for the entire car, inspect each window, especially the edges and corners. If any bubbles are found, address them immediately.
6
5
Share

Which Signal to Watch When Turning Left?

When there is a dedicated left-turn traffic light, proceed when it turns green. If there is no dedicated left-turn signal, you may turn left when the straight-ahead light is green. Precautions for using turn signals are as follows: While driving: When traffic in your lane is congested and you need to change lanes, check the adjacent lane through the rearview mirror to ensure it is clear. Without obstructing vehicles in other lanes, activate the corresponding turn signal before changing lanes. When making a U-turn: Activate the left turn signal and observe for any oncoming vehicles in front or behind before executing the turn. Honking: On road sections without a solid centerline marking, when overtaking, activate the left turn signal and honk. If being overtaken, yield by moving to the right. When pulling over to park: Activate the right turn signal in advance and observe the traffic situation to the right rear before pulling over. When leaving a parking spot: Activate the left turn signal in advance and observe the traffic situation to the left rear before merging into the traffic lane.
10
1
Share

What to Do If You Lack a Sense of the Car?

Observe the rearview mirror while driving. Make good use of the rearview mirrors to monitor the sides of the vehicle and the distance from the lane dividers. Pay attention to the distance of the vehicle behind you. Always check the rearview mirror when changing lanes. Additionally, during startup, especially for novice drivers, manual transmission cars are more prone to stalling. It's important to master the reverse gear.
12
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.