What to Do When Wuling Hongguang's Air Conditioning Has Poor Cooling Effect?

2 Answers
MacZoey
07/29/25 3:09am
Here are the specific reasons and solutions for the poor cooling effect of Wuling Hongguang's air conditioning: 1. Insufficient or low refrigerant: This may be caused by a minor refrigerant leak. You can observe it through the sight glass on the dryer tank. When the air conditioning is running normally, if there are continuous, slow bubbles in the sight glass, it indicates insufficient refrigerant. If obvious bubble flipping occurs, it means the refrigerant is severely insufficient. In this case, simply adding refrigerant will solve the problem. 2. Loose drive belt of the car air conditioning compressor: If the drive belt is loose, the compressor will slip during operation, leading to reduced transmission efficiency and a drop in compressor speed. This results in decreased delivery of compressed refrigerant, causing the car air conditioning to not cool properly. If the compressor drive belt is too loose, it should be tightened. If it cannot be turned by hand, it means the belt is too tight and should be loosened slightly. If tightening is ineffective or the belt shows signs of cracking, aging, or other damage, a new drive belt should be installed.
Was this review help?
3
0
Share
LaReese
08/12/25 7:02am
I've encountered air conditioning cooling issues with my Wuling Hongguang after prolonged use. Driving in summer feels like being in a sauna, and the lack of cool air is really annoying. Last time I checked, the air filter was clogged with dust. Simply removing it for cleaning or spending a few dozen yuan to replace it with a new filter immediately restored the airflow. If the refrigerant is low, the compressor noise increases but cooling is insufficient—this requires a shop visit to check for leaks and top up the refrigerant. Dirt on the radiator surface also affects heat dissipation; try rinsing it with a hose. A non-spinning or slow-running fan is another potential issue—test its operation yourself. Don’t underestimate these problems; timely action can prevent worse situations. I recommend regular maintenance of the AC system, checking the filter condition frequently to reduce sudden failures.
Was this review help?
13
4
Share
Expand All
More Forum Discussions

Which brand of carbon deposit cleaner is good to use?

Carbon deposit cleaners can be chosen from brands such as 3M, BASF, or Chevron. Below is extended information about carbon deposit cleaners: 1. Limitations of cleaners: Engine carbon deposit cleaners do have practical effects, but due to the short duration they remain in the engine for cleaning, combined with the inherent limitations of non-disassembly cleaning methods, their cleaning effectiveness is relatively limited. 2. How to use carbon deposit cleaners: The cleaner is directly added to the fuel tank to mix with the fuel, and then the vehicle is started. The cleaner will enter the combustion chamber along with the fuel, and while it does, it will clean the carbon deposits inside the engine to a certain extent. Due to the heavy workload and time-consuming nature, most 4S shops do not offer disassembly cleaning services.
2
4
Share

What causes gear shift jerking in the Mercedes-Benz GLK300 transmission?

Mercedes-Benz GLK300 transmission gear shift jerking may be caused by solenoid valve damage or transmission control module failure. The specific reasons and solutions are as follows: Solenoid valve damage: If sludge in the transmission oil circulates and blocks the oil passages in the valve body, gear shift jerking will occur. Prolonged operation under this condition can lead to a series of transmission issues such as overheating, impact, and slippage. The solution is to repair the solenoid valve. Transmission control module failure: The control module serves as the central heart of the transmission, responsible for communicating with the vehicle's main computer, collecting signals, and sending commands. Module failure primarily affects these instruction transmissions. The solution is to perform repair work.
13
2
Share

What causes the Audi A6L to shake when starting?

Audi A6L shaking when starting is caused by abnormalities in the intake system, engine carbon buildup, etc. The specific reasons and solutions are as follows: Abnormalities in the intake system: When the engine is running, the driver controls the throttle opening via the accelerator pedal to adjust the intake volume and regulate engine operation. Issues such as insufficient power and poor acceleration may result from damage to certain components of the intake system. The solution is to replace the relevant parts. Engine carbon buildup: Carbon deposits on the engine's valves and intake passages can absorb an appropriate amount of fuel, failing to achieve the required power performance, leading to shaking when the car starts. The solution is to perform a system cleaning.
13
5
Share

What is the solution for the 3008 burning engine oil?

To resolve the issue of burning engine oil, it is essential to address carbon buildup on the piston rings, wear between the pistons and cylinder walls, valve stem seals, and crankshaft seals, with particular attention to solving the crankshaft seal problem. Burning engine oil occurs when oil enters the engine's combustion chamber and mixes with the air-fuel mixture for combustion. The phenomenon of 'burning engine oil' in a vehicle can lead to premature failure of the oxygen sensor, increased carbon deposits in the combustion chamber, unstable idling, reduced acceleration power, higher fuel consumption, and excessive exhaust emissions. In severe cases, insufficient engine lubrication can cause irreparable damage or even complete engine failure, significantly increasing repair costs and posing potential safety hazards.
5
2
Share

What is the difference between second gear and reverse gear?

The difference between second gear and reverse gear lies in their different positions. Car owners need to pay attention to the positions of these two gears while driving. Below is a detailed introduction about car gears: 1. Speed range: First gear corresponds to a speed of 0-5km/h. Second gear corresponds to 5-20km/h, third gear to 20-40km/h, fourth gear to 40-60km/h, and fifth gear to 60-100km/h. 2. Gear shifting timing: Generally, the optimal time to shift gears is when the engine speed reaches 2000r/min, and should not exceed 2500r/min. For some high-displacement and high-power engines, shifting around 3000r/min is acceptable.
5
4
Share

Does the CS85 have a four-wheel drive model?

Currently, the CS85 does not have a four-wheel drive model. It is a front-engine, front-wheel-drive vehicle. Front-wheel drive refers to a car design where the engine only drives the front pair of wheels, a configuration used by most sedans today. Some urban SUVs are equipped with on-demand four-wheel drive technology, which means the vehicle is primarily front-wheel drive, but when the front wheels slip, power is distributed to the rear wheels. Urban SUVs with on-demand four-wheel drive have better off-road capability than front-wheel-drive SUVs, and they also have relatively lower fuel consumption. The Great Wall CS85 uses a MacPherson strut independent suspension for the front and a multi-link independent suspension for the rear.
15
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.