What to Do When There's Noise When Braking?

1 Answers
Camille
07/30/25 10:55am
If it's a new car, it's normal to hear some noise when braking, and it should go away after driving for a while. If the car has been driven for a long time, the brake discs or brake pads might be rusty, and you can remove them to sand off the rust layer. Below are specific solutions for noise when braking: 1. Rust on brake discs or brake pads. After parking for a long time, especially in humid or rainy weather, some rust or dirt may appear on the brake discs or pads. This can usually be resolved by driving for a while, or you can apply butter or specialized lubricant to the connection between the brake pads and calipers. 2. New brake pads. New cars or recently replaced brake pads may produce similar noises. New brake pads and discs require a break-in period, and such noise during braking is completely normal. However, if the noise persists after driving for an extended period, there may indeed be an issue. 3. Excessive wear on brake discs or pads. Both brake discs and pads are high-wear items, as they constantly rub against each other during braking. Over time, they naturally wear out, and excessive wear can lead to noise. Therefore, regular maintenance and replacement are necessary. Typically, brake pads should be replaced every 60,000–80,000 kilometers, while brake discs should be replaced every 100,000–120,000 kilometers.
Was this review help?
16
3
Share
More Forum Discussions

How to Turn on the Heating in a Passat Car?

Here are the steps to turn on the heating in a Passat car: 1. Start the car and wait for about 5-10 minutes until the engine coolant reaches the normal operating temperature, then turn on the heating switch. 2. Adjust the air conditioning circulation mode to the internal circulation setting. 3. Rotate the air conditioning mode selector to the heating mode. 4. Do not press the AC button, as the heating system utilizes the car's own heat circulation and does not require the air conditioning compressor. 5. Adjust the air conditioning fan speed and direct the airflow by positioning the vents as desired. Additional information on how to turn on the cooling in a Passat: 1. For automatic air conditioning, simply press the AUTO button, and it will adjust according to the interior temperature. 2. For manual air conditioning, switch to the cooling mode.
4
5
Share

Does Replacing the Front Bumper Affect Future Car Sales?

The impact of replacing a bumper on a car varies depending on the vehicle. If the car's original value is relatively high, changing the bumper will have a greater effect on its resale value. However, if the car's original value is not high, replacing the bumper will have minimal impact. Function of the Bumper: Installing bumpers at the front and rear of a car not only serves a decorative purpose but also absorbs and mitigates external impacts, protecting the vehicle body and ensuring the safety of passengers inside. It acts as a safety device. Material of the Front Bumper: In the past, both front and rear bumpers of cars were made of metal materials, typically pressed from steel plates over three millimeters thick, with a chrome-plated surface. These were welded to the car's frame longitudinal beams, leaving a noticeable gap between the bumper and the body, which made the bumpers look quite unattractive. With the continuous development of the automotive industry, car bumpers have undergone innovation. Today, front and rear bumpers maintain their original protective functions while also pursuing lightweight design. Modern car bumpers are now made of plastic.
11
0
Share

What is the function of the engine tachometer?

The function of the engine tachometer is to monitor the working status of the engine. Ignition phase: A four-cylinder gasoline engine generally needs to reach about 80 revolutions per minute (rpm) to ensure successful ignition, but in practice, the speed is usually increased to 120 rpm to guarantee ignition quality. Without a tachometer, you wouldn't even know if the engine has a problem. Start-up moment: At the moment of engine start-up, the speed often reaches 1200-1500 rpm, and even higher in cold weather. However, the speed during cold start should not be too high because the lubricating oil hasn't reached the upper part of the engine yet. To reduce wear, it's best to keep it below 2000 rpm. Gear shifting timing: The tachometer can also indicate the optimal time for manual transmission gear shifting. Generally, shifting at around 2500 rpm is the smoothest and most fuel-efficient. If more power is needed, shift above 3000 rpm.
5
0
Share

Can a Motorcycle Jump-Start a Car?

Motorcycles cannot jump-start cars as doing so may damage the motorcycle's battery. Reasons why it's not possible: Car batteries typically have a capacity of around 50AH, while motorcycle batteries only have about 7AH. Although the voltage is the same, the instantaneous current when starting a car can reach approximately 200A, far exceeding the capacity of a motorcycle battery. This puts significant strain on the motorcycle battery, and after a few attempts, the battery may become depleted and eventually fail. It is recommended to use another car for jump-starting instead. Car batteries can jump-start motorcycles: The starting current of a car engine generally ranges from 200A to 400A or more, while a motorcycle engine's starting current is around 30A to 50A. The capacity and starting current output of their respective batteries differ: car batteries have a larger capacity and higher starting current output, whereas motorcycle batteries have a smaller capacity and lower starting current output. Therefore, a car battery can be used to jump-start a motorcycle, but a motorcycle battery cannot start a car. Otherwise, the high starting current could damage the motorcycle battery's plates, rendering it useless.
1
1
Share

What Happens If Engine Oil Is Underfilled?

If the amount of oil added is slightly low, as long as the level is between the upper and lower marks on the dipstick, there is no problem. Even if it is one liter short, it will not have any impact. However, if the oil level is below the minimum mark, even if there is some oil left in the tank, it is necessary to promptly visit a 4S shop or manually top up the oil. Below are some precautions when adding oil: 1. Avoid aggressive driving, as the engine temperature will rise under high-speed operation. When the oil level is low, it can easily cause the engine to overheat, and in severe cases, the engine may be completely damaged. 2. Overfilling the oil is also not advisable. Excess oil can easily enter the combustion chamber (due to excessive internal pressure) and produce gummy carbon deposits. Over time, these deposits will become increasingly severe, not only clogging the catalytic converter holes and causing excessive exhaust emissions (increased fuel consumption), but in severe cases, it may also lead to oil burning. Additionally, excessive oil can reduce the gas volume in the crankcase, increase pressure, and cause oil seals to leak.
14
3
Share

Is transmission fluid maintenance based on mileage or years?

Transmission fluid maintenance is based on both mileage and years, whichever comes first. Signs that transmission fluid needs replacement include: vehicle shaking, gear shifting hesitation; transmission overheating warning light on the dashboard; engine stalling; unusual noises. Different vehicle models have different replacement cycles. Below are the transmission fluid replacement cycles: Manual transmission: Manual transmission fluid is generally recommended to be replaced every 3 years or approximately 100,000 kilometers. Automatic transmission: Automatic transmission fluid is generally recommended to be replaced every 2 years or approximately 40,000 kilometers. Continuously variable transmission (CVT): CVT fluid is generally recommended to be replaced every 2 years or approximately 60,000 kilometers. The methods for replacing transmission fluid are as follows: Unscrew the drain plug at the bottom of the transmission to drain the old fluid before refilling. Remove the transmission oil pan directly to drain and refill: This method provides more thorough replacement than the previous one by removing impurities from the bottom of the oil pan. Using a circulation machine to replace automatic transmission fluid: Dynamic fluid replacement with an intelligent circulation machine can filter and clean sludge and impurities inside the automatic transmission.
17
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.