···
Log in / Register

What to Do When There is Abnormal Noise When Opening and Closing Car Doors?

4 Answers
BennettDella
07/24/25 3:36pm
The solution to abnormal noise when opening and closing car doors is: Use a cloth or tissue to wipe off the dust on the door hinges and limiters, then use a cotton swab with a small amount of lubricating oil to repeatedly apply to the red-circled areas of the door hinges and limiters. After that, repeatedly open and close the car door, and repeat the steps of applying oil and opening/closing the door until the abnormal noise disappears. Be careful not to apply too much lubricating oil to avoid contaminating other parts of the door. The cause of abnormal noise when opening and closing car doors is: Issues with the door hinges and limiters. Due to years of use, the door hinges and limiters may experience wear and tear, and dust may enter the gaps, leading to a lack of lubrication. This results in vibration interference during the door opening and closing process, causing abnormal noise.
Was this review help?
20
2
Share
VanEmilia
08/10/25 7:26am
My own car's door makes a squeaking sound when opening and closing, usually due to issues with the hinges or door seals. Rusty hinges or lack of lubrication are the most common causes. You can spray some specialized lubricant, like WD-40 available at auto shops, lightly on the hinge joints and stoppers. If it still squeaks after spraying, try checking the door seals—aging seals can cause friction and noise, and wiping them clean with a damp cloth might solve the problem. Last time I had this issue, I found a loose bolt inside the door; tightening it fixed the noise. Parking in shaded areas and avoiding rain can help delay rust. It's best to check monthly—this noise isn’t just annoying but could also be an early sign of door lock issues. A repair shop visit is cheap, or you can DIY in 5 minutes. Don’t ignore small issues to avoid bigger repairs later.
Was this review help?
4
0
Share
Expand All
StLeilani
09/25/25 7:37am
The creaking sound from the door switch is really annoying, and I always pay attention to these small details from a safety perspective. The noise could be a sign of hinge wear, and not fixing it in time might lead to door deformation or poor sealing, which would be dangerous when driving at high speeds. You can try lubricating the hinges yourself first – buy a bottle of automotive lubricant and spray it a few times to see if it helps. If the noise persists, check if the door stopper or rubber seal is damaged. It's best to perform maintenance every quarter to prevent rust and dust buildup. If left unfixed, the noise could escalate into water leakage or lock failure. Last time I went out with my child, I heard the sound and immediately went to a professional shop. It only cost 100 yuan to fix, and I felt much more at ease. The key is not to delay, as it could affect driving safety.
Was this review help?
11
5
Share
Expand All
MacAlex
11/09/25 2:57am
Simply put, I've had squeaky car doors too, and spraying some lubricant on the hinges fixed it. Use a dedicated spray like WD-40, available at hardware stores. If that doesn't work, dirty weatherstripping can also cause noise—try cleaning it. Still no luck? Just visit a repair shop; it's a 10-minute job. Don't delay on such a minor issue.
Was this review help?
10
2
Share
Expand All
More Forum Discussions

What brand is the engine of the New Baojun RC6?

The engine brand of the New Baojun RC6 is SAIC-GM. The car is equipped with a 1.5T turbocharged engine, with a maximum power of 108 kW, a maximum torque of 245 Nm, a maximum power speed of 5,200 rpm, and a maximum torque speed ranging from 2,200 to 3,400 rpm. In terms of the transmission system, it is paired with a 6-speed manual transmission and a CVT continuously variable transmission. The New Baojun RC6 is a compact SUV launched by Baojun Auto, with dimensions of 4,925 mm in length, 1,880 mm in width, and 1,580 mm in height, and a wheelbase of 2,800 mm. The car's exterior adopts the design concept of 'Interstellar Geometry,' featuring a very stylish overall design, with a fastback silhouette that further highlights its sporty character.
7
5
Share

How to Reset the Tire Pressure Warning Light on the Honda Avancier?

The method to reset the tire pressure warning light on the Honda Avancier is: 1. Start the engine and keep the gear in P position; 2. Select 'Home' on the central control screen to enter the settings interface; 3. Choose the vehicle menu; 4. Select the 'Tire Pressure Monitoring System Calibration' option to complete the calibration. The Honda Avancier is a 5-door, 5-seater midsize SUV with body dimensions of 4858mm in length, 1942mm in width, and 1670mm in height, with a wheelbase of 2820mm. It is equipped with a 1.5T turbocharged engine and a CVT continuously variable transmission, delivering a maximum power of 142 kW and a maximum torque of 243 Nm. The suspension system features MacPherson strut independent suspension at the front and multi-link independent suspension at the rear.
6
2
Share

What are the reasons for the malfunction of the headlight range control?

Prompting a malfunction in the headlight range control is due to a failure in the adaptive cruise headlight steering. Below are the specific details about adaptive cruise headlights: 1. Function: The Adaptive Front-lighting System (AFS) adjusts the direction of the headlight beam according to current driving conditions, moving the beam left or right based on vehicle speed and steering wheel angle. The system works in conjunction with the headlight direction automatic adjustment system to improve visibility during turns and at intersections. 2. Usage: The system starts operating when the vehicle speed exceeds 10 km/h. It can operate within the maximum range of the steering wheel angle. If you do not wish to activate the system, press the "AFS OFF" button to turn it off. To turn it on again, press the same button. When the system is off, the "AFS OFF" indicator on the instrument cluster lights up. If the system malfunctions, the "AFS OFF" indicator on the instrument cluster will flash.
13
1
Share

How many liters of transmission oil does the Sagitar require?

The Sagitar 1.6 requires 4 liters of transmission oil for a standard refill, while 8 liters are needed if using a circulating oil change machine. The oil filler port is located on the right side at the rear of the transmission. It is essential to regularly check the automatic transmission fluid level. The method for checking transmission oil is as follows: 1. Start the engine and warm up the transmission oil to approximately 50°C. Then, move the gear selector through each position, pausing for 2 seconds in each, before placing it in the parking position. At this point, the oil level on the dipstick should be between the maximum and minimum marks. If it is insufficient, promptly add oil of the same quality. 2. For most automatic transmissions, the oil change interval is typically every two years or 40,000 to 60,000 kilometers (refer to the vehicle's manual for specifics). However, it is advisable to change the oil 2,000 to 3,000 kilometers earlier than recommended.
17
1
Share

Why Do Some Cars Have Antennas While Others Don't?

Car antennas are devices that intercept high-frequency radio waves transmitted by broadcasting stations and transmit them to the car's radio, mobile phone, or radio navigation equipment receiver for demodulation. Every car is equipped with an antenna, but the reason some don't have visible external antennas is mainly because certain models use glass antennas. Here are the relevant details: 1. External Antennas: In vehicles produced in earlier years, the in-car radio used manually pulled or electrically retractable rod antennas to receive radio waves, enabling the vehicle to receive radio signals while driving. Since these antennas protrude from the car body, they are more prone to damage when parking in lots or during car washes. 2. Glass Antennas: Also known as hidden antennas, these achieve signal reception by printing conductive lines on the rear windshield. They offer advantages such as low cost, low failure rates, and high reception quality, making them the future trend for car antennas. Glass antennas use metal coatings as antennas, coupling electromagnetic signals through metal patches or printed silver paste, which are then fed to the signal amplifier or radio via tabs.
13
0
Share

Reasons for the Right Front Wheel Crossing the Line in a 90-Degree Turn

The main reason for the right front wheel crossing the line in a 90-degree turn is an incorrect entry angle. Here is a detailed introduction to the techniques for a 90-degree turn: 1. Entering the turn: For a left turn, approach the corner, keeping 300mm from the side line, and enter the turn. 2. Steering: When the left rearview mirror aligns with the inner corner of the turn, turn the steering wheel fully to the left and proceed out of the corner. Before turning, try to drive as close to the outer side as possible. Only start turning inward slowly when the front of the car is about 500~700mm from the opposite side line. 3. Exiting the turn: Align the front of the car with the exit, straighten the steering wheel, and continue forward. While looking ahead, also observe the rearview mirror. When you feel the middle of the car is about to reach the vertex of the corner, slowly straighten the steering wheel and gradually adjust the car's direction until it completely exits the turn, completing the 90-degree turn.
16
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.