What to Do When the Windshield Wipers Leave a Blurry Streak?

How to Complete the Required Hours for Subject Three Quickly?

Dedicating four hours daily to practice is the fastest method. According to the "Motor Vehicle Driver Training and Examination Syllabus," the total training hours for Subject Three must reach 34 hours. This includes 24 hours of practical road driving skills training and 10 hours of safety and civilized driving theory. The daily training duration must not exceed 4 hours. Additional Information: 1. Road Driving Skills Test Content for Subject Three: Vehicle preparation, simulated lighting test, starting, driving in a straight line, gear shifting operations, lane changing, parking by the roadside, proceeding straight through intersections, turning left at intersections, turning right at intersections, crossing pedestrian crossings, passing school zones, passing bus stops, meeting oncoming vehicles, overtaking, making U-turns, and nighttime driving. 2. Safety and Civilized Driving Theory Test Content: Requirements for safe and civilized driving operations, safe driving knowledge under adverse weather and complex road conditions, emergency handling methods for situations like tire blowouts, and post-accident handling knowledge.

15

3

Share

What Causes the Classic Focus to Feel Sluggish and Lack Power During Acceleration?

Focus feeling sluggish and lacking power during acceleration may be due to an intake system malfunction or a fuel supply system issue. Here are some explanations regarding the Focus feeling sluggish and lacking power during acceleration: 1. Lack of Power During Acceleration and the Intake System: The air supply system primarily provides an appropriate amount of air to match the fuel, and the purity of the air directly affects combustion efficiency, which in turn influences power output. Therefore, when experiencing a lack of power during acceleration, the first step is to check whether the intake system is functioning properly. If it appears intact, consider whether the intake system needs cleaning. Remove the air filter and blow out the dust; if it cannot be cleaned thoroughly, replace it. Inspect the throttle body for cleanliness, and further examine the intake valves and intake manifold. Clean them if necessary. If the acceleration still feels sluggish after inspecting and cleaning the intake system, it can be concluded that the issue is unrelated to the intake system. General idle shaking can often be resolved by cleaning the intake system. 2. Lack of Power During Acceleration and the Fuel Supply System: The amount of fuel supplied directly determines the strength of the power output, and the complete combustion of fuel ensures consistent power. Therefore, when experiencing insufficient power, the fuel supply system should also be considered. First, ensure the fuel meets the vehicle's standards. If the fuel lines and connections are intact, inspect the fuel filter, fuel injectors, and fuel pump for any blockages in fuel delivery. Clean or replace them if necessary. Checking the fuel supply system ensures smooth fuel delivery and injection, and a properly functioning fuel pump will eliminate potential obstacles for subsequent operations.

20

1

Share

How to Correct Direction for Front Wheel Skid and Rear Wheel Skid?

When the front wheels skid, the steering wheel should be corrected in the opposite direction; when the rear wheels skid, the steering wheel should be corrected in the direction of the skid, and the vehicle should return to the road after the rear wheels are straightened. Vehicle skidding refers to the phenomenon of sudden acceleration or sudden lateral swinging, which is more likely to occur on curves or in rainy or snowy weather. If a skid suddenly occurs while driving, the driver should try to stay calm, hold the steering wheel firmly with both hands, quickly identify which tire is skidding, immediately release the brake pedal, and swiftly turn the steering wheel in the direction of the skid. On icy or snowy roads, drivers should never use emergency braking. Emergency braking not only fails to stop the vehicle but can also accelerate skidding or even cause the vehicle to roll over. If skidding occurs while going downhill, the driver can accelerate appropriately. If skidding occurs during a turn, the driver should slowly release the accelerator and turn the steering wheel to correct the direction, but be careful not to turn the steering wheel too much to avoid losing control and causing an accident. During a skid, do not abruptly turn the steering wheel or use the foot brake. Immediately release the brake pedal, turn the steering wheel toward the side of the skid, and promptly adjust and correct the direction before continuing to drive.

15

1

Share

What is the foot brake?

The foot brake is the service brake. The service brake is a braking device that stops or reduces the speed of a moving vehicle. It achieves braking through intense friction between the brake pads and the brake drum. In contrast, the handbrake is a parking device and should not be used for braking during driving except in emergencies. Here is a related introduction to the classification of braking systems: 1. Throttle control braking: When deceleration is needed, maintain the 3rd gear position and fully release the throttle. At this point, the engine tends to idle, creating resistance in the drivetrain that acts on the wheels to slow the vehicle down. 2. Exhaust brake: High-power diesel engines have a butterfly valve at the connection between the exhaust manifold and the exhaust pipe. In gear, operating the electromagnetic switch closes the valve, causing the engine to stall and achieve braking. It automatically opens when the throttle is pressed again. Simple in structure but harmful to the engine. Commonly used in heavy trucks and buses. 3. Hydraulic torque converter retarder: A turbine chamber is added at the rear of the transmission housing. When the braking circuit is activated, transmission oil generates damping in the turbine to achieve braking. No wear but requires additional cooling. Currently used in ZF transmissions for high-end buses. 4. Electric turbine retarder: Essentially a "generator" installed on the driveshaft. When not powered, there is no contact or wear. When braking is needed, the circuit is activated, and the driveshaft is subjected to electromagnetic resistance to achieve braking. No wear but bulky in structure. Optional for heavy trucks and buses. 5. Engine braking structure: The braking signal slightly opens the exhaust valve without closing it, creating airflow resistance during piston movement to generate braking force. Compact and non-damaging, currently not available domestically.

2

5

Share

What is the purpose of Subject 2 simulation training?

Subject 2 simulation is designed to mimic the formal Subject 2 driving test, aiming to improve the pass rate. The simulation covers the same test items as the actual exam, serving as a practice test. Below are some key points to note for the Subject 2 test: 1. Reverse parking into a garage: (1) Ensure accurate alignment with reference points and lines, and monitor the distance between the vehicle body and the line via the rearview mirror to prevent the body from crossing the line. (2) Do not stop the vehicle until it is completely inside the garage; pay attention to clutch control to avoid stopping midway or incomplete parking. 2. Parallel parking: (1) Maintain proper distance from the garage when aligning the vehicle, avoiding crossing the line, and be cautious not to run over the garage corner when exiting. (2) Remember to use the turn signal when exiting the garage.

1

4

Share

How to Solve the Problem of Car Compressor Starting and Stopping Intermittently?

Here are the solutions for the issue of car compressor starting and stopping intermittently: 1. Check if the car air conditioning's energy-saving mode is activated. 2. High exhaust pressure and low suction pressure. Moisture in the system may cause pipe blockage leading to icing. Use high-pressure nitrogen to flush the pipes for repair. 3. Check the remaining amount of refrigerant. The amount of refrigerant determines the system pressure, and abnormal pressure can cause frequent starting and stopping of the compressor. 4. Appropriately increase the limit value of the high-pressure relay and decrease the limit value of the low-pressure relay. If the limit values for high and low pressure are set too high, the relay will automatically disconnect and stop working when the voltage slightly exceeds the limit.

12

3

Share

What to Do When the Windshield Wipers Leave a Blurry Streak?

How to Complete the Required Hours for Subject Three Quickly?

What Causes the Classic Focus to Feel Sluggish and Lack Power During Acceleration?

How to Correct Direction for Front Wheel Skid and Rear Wheel Skid?

What is the foot brake?

What is the purpose of Subject 2 simulation training?

How to Solve the Problem of Car Compressor Starting and Stopping Intermittently?

Why Are Used Geely GX7 Cars So Cheap?

What is the speed when exceeding the 120 km/h limit by 10%?

What to Do When Your Driver's License Expires?

How Many Times Can You Take the Driving License Subject 4 Exam?