What to Do When the Vehicle's Braking System Shows Abnormal Warning?

1 Answers
WilliamFitz
07/29/25 4:33pm
Here are the solutions when the vehicle's braking system shows abnormal warning: Solutions: It is recommended to promptly visit a 4S shop for inspection and repair if the braking system shows abnormalities. The operational condition of a vehicle's braking system determines the safety of passengers. Only when it's in proper working condition can it effectively decelerate or stop the vehicle according to the driver's commands. Symptoms of braking system abnormalities: There are various manifestations of brake system failures. A common symptom is when the brake pedal doesn't return after being pressed. This is usually caused by insufficient brake fluid, requiring inspection for leaks at the wheel cylinders, pipelines, and connectors, or checking whether the master cylinder or wheel cylinder components are damaged. Another scenario is when the braking effect remains poor even with the pedal fully depressed. This may indicate air in the brake system. If the braking improves after repeatedly pumping the pedal, the likely cause is excessive clearance between the friction pads and brake drums, necessitating inspection and repair at a 4S shop.
Was this review help?
6
3
Share
More Forum Discussions

How to Start an Accord with the Key?

Insert the key and turn it to the ACC position, then pause for 2-3 seconds to allow the main power relay contacts to stabilize and power the first set of components that require electricity. Continue turning the key to the ON position, then pause again for 6-10 seconds to allow the fuel pump relay to engage. After waiting for all sensors to adjust their states, turn the key to the START position until the engine runs continuously, then return it to the ON position. Under the guidance of the computer, the system will automatically adjust to the optimal position and parameters, enabling the engine to start.
16
0
Share

How to Fix One Daytime Running Light Being Dim?

Start the vehicle's engine and turn on the daytime running lights to observe. Check if the voltage at the connector of the non-functioning light is normal. If it is normal, it indicates that the daytime running light is damaged. If the voltage is abnormal, check for any short circuits in the wiring or if the fuse is blown. Replace the fuse if necessary. If there are no issues with the wiring, you can remove the light cover to inspect the bulb. Simply replace the daytime running light bulb. After completing the inspection, turn off the vehicle's engine and close the doors properly.
9
2
Share

What is the difference between parking radar and reversing radar?

The differences between parking radar and reversing radar are: 1. Different functions: Parking radar is used to detect the distance of obstacles in front of the car when parking or driving at low speed, providing information on the distance, direction, and area of obstacles; Reversing radar informs the driver of the surrounding obstacles through sound or more intuitive display. 2. Different components: Parking radar consists of a front controller, sensors, and an indicator; Reversing radar is composed of ultrasonic sensors, a controller, and a display or buzzer. Both parking radar and reversing radar are safety auxiliary devices for parking or reversing a car, which can relieve the troubles caused by the driver's need to look around when parking, reversing, or starting the vehicle, and help the driver eliminate blind spots and unclear vision.
2
4
Share

How to reset the tire pressure light on Chery 5x?

Press the left combination button on the steering wheel to switch the display page information to the tire pressure display interface and view the real-time information of the tire pressure monitoring system. If the tire pressure monitoring system still does not receive the wireless RF signal from one or more sensors after 10 minutes. At this time, if you need to reset it, first check whether the tires are normal. If there is no fault in the tires, you only need to drive a few kilometers. Let the computer re-record the tire information to reset the tire monitoring system.
16
4
Share

How to Use the Auto Hold Function in Haval Big Dog

When the vehicle comes to a complete stop, do not release the brake pedal. Instead, press the brake pedal further down (until it cannot be pressed any further). The "HOLD" indicator will appear on the instrument screen, indicating that the parking assist function is activated. At this point, you can release the brake pedal.
7
0
Share

How to Change the Vehicle Owner's Mobile Number?

The vehicle owner needs to bring their original ID card to the internet service window of the vehicle management office (located inside the fee payment hall) to make the change. Direct login for changes. If the phone number used for registration is different from the registered phone number, the registration will not be successful. If the vehicle owner forgets the registered phone number, they can call the vehicle management office to inquire about the details. If necessary, the owner may need to visit in person. If someone else is handling the process on behalf of the owner, they must also submit the original ID card of the agent and a written authorization from the owner.
3
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.