Browse

Antiques Collectibles Apparel Baby Kids Items Books， Movies And Music Electronics Free Stuff Garden Outdoor Health Beauty Home Goods Home Improvement Supplies Musical Instruments Office Supplies Pet Supplies Sporting Goods Ticket Toys Games Transportation Others

Used Cars New Cars Others

Business Crafts Design And Web Events Home Improvement Legal Lessons Personal Pets Photography Repair And Technical Support Wellness Writing， Translation， And Transcription Others

Activities & Groups Artists & Musicians Classes & Lessons Events Friendship & Networking Lost & Found Rideshare Sports Teams Volunteers Travel & Travel Partners Skills & Language Swap Other

What to Do When the Transmission Fails?

2 Answers

Raymond

07/24/25 4:20am

Transmission oil temperature should not exceed 120 degrees, with 80 or 90 degrees being optimal. Prolonged exposure to temperatures higher than this can accelerate the degradation of the transmission oil's composition and usability. When the oil temperature reaches 143 degrees, the transmission oil is likely to lose its lubricating properties, which can cause internal transmission components to fail due to excessive friction and overheating. Below is additional information about transmissions: 1. As one of the "three major components" in a vehicle, the quality of the transmission directly affects the car's handling and safety. If the transmission fails, it can easily lead to traffic accidents. Many transmission failures are caused by high temperatures and overheating, requiring immediate cooling. 2. According to data analysis, over 90% of automatic transmission failures are due to high temperatures and overheating. Excessive transmission oil temperature can lead to a series of transmission problems, and in severe cases, it can cause transmission damage or even traffic accidents.

Was this review help?

7

1

Share

DeAugust

08/10/25 11:55pm

Transmission failure is no small matter, safety first! If you notice difficulty shifting gears or unusual noises, immediately pull over and turn off the engine. Never force the vehicle to keep going, or the transmission gears could be completely ruined. Next, check the transmission fluid: pop the hood, locate the fluid reservoir, and inspect if the fluid level is adequate and the color is clear. If it's too low or dirty, top it up with some automatic transmission fluid as a temporary fix. But don't attempt to repair complex components yourself—it's best to call a tow truck and have the vehicle taken to a professional repair shop for a technician's diagnosis. I've encountered similar situations before, and delaying repairs can lead to a chain reaction, causing repair costs to skyrocket to tens of thousands. Remember to perform regular maintenance and oil changes, and have it checked every two years to prevent major issues.

Was this review help?

20

1

Share

Expand All

More Forum Discussions

How to view tire pressure monitoring on Audi Q3?

The method to view tire pressure monitoring on Audi Q3 is: When there is insufficient tire pressure or a system malfunction, the tire pressure monitoring display will appear in the instrument cluster. The Audi Q3 is a compact 5-door, 5-seat SUV with body dimensions of: length 4481mm, width 1848mm, height 1616mm, wheelbase 2680mm, and fuel tank capacity of 60 liters. The Audi Q3 is equipped with a 1.4T turbocharged engine and a 7-speed dual-clutch transmission, with a maximum power of 110 kilowatts and a maximum power speed range of 5000 to 6000 revolutions per minute. Its drive system is front-wheel drive, with MacPherson strut independent suspension at the front and torsion beam non-independent suspension at the rear.

Does Using a Car Fan Damage the Battery?

Using a car fan does not damage the battery. The reasons are as follows: 1. When the vehicle is started, the car fan is powered by the engine, so using the fan during normal driving has no impact. 2. For the battery, the most damaging practices are leaving the headlights and air conditioning on when the car is turned off. Common habits that harm the battery include: 1. To save fuel, turning off the engine while waiting by the roadside and then continuing to use the air conditioning for cooling. This consumes a significant amount of power, leading to battery drain and shortening its lifespan. 2. Charging devices via USB cable after turning off the vehicle. This can cause the battery to lose charge. 3. Playing music through the car radio at high volume after turning off the engine. In general, most of the vehicle's electrical devices are powered by the battery when the engine is off, and prolonged high-volume music playback can lead to excessive battery drain.

What is the troubleshooting method for a car generator not generating electricity?

The troubleshooting method for a car generator not generating electricity is: 1. Tighten the adjustment device or replace the belt; 2. Check the condition of the wires; 3. Inspect whether the rotor part operates smoothly; 4. Use a multimeter to measure whether the coil resistance is normal; 5. Rewind the coil or replace the motor. The detection methods for a car generator not generating electricity are: 1. Use a multimeter in voltage mode for detection; 2. Use an external ammeter for detection; 3. The test lamp method; 4. Change the engine speed and observe the headlight brightness method; 5. Remove the battery ground connection to see if the engine works method. The function of a car generator is: Using the electromagnetic induction principle where conductors cut magnetic lines to generate potential, it converts the mechanical energy of the prime mover into electrical energy output.

Why is there water in the trunk?

The reasons for water in the trunk are as follows: 1. Poor rainwater drainage around the trunk lid. 2. Insufficient compression force on the sealing strip at certain positions after closing the trunk lid. 3. Deformation or leakage points in the trunk lid. 4. Corrosion of the sealing strip. Solutions for water ingress in the trunk: 1. Drain the water as soon as possible. There is a rubber drain plug at the bottom of the spare tire compartment in the trunk - remove it to drain the water. 2. Quickly locate the leak source. Check if the trunk lid is deformed, inspect the condition of the surrounding rubber seals, or observe light penetration points with the lid closed (mark these spots). 3. Ventilate the trunk. Remove all items and the trunk liner, then leave the lid open for an hour to prevent mold and rust formation.

What are the symptoms of a faulty plain bearing?

Here are the symptoms of a faulty plain bearing: 1. When turning the steering wheel while stationary or at low speeds, a "squeak... squeak" sound may be heard, and in severe cases, vibration in the steering wheel can be felt. 2. When driving on bumpy roads or over speed bumps, a "thud... thud" sound may be heard. 3. Tire noise becomes noticeably louder during driving, and in severe cases, a "hum... hum" sound may be present. 4. The vehicle may pull to one side. Here is a detailed introduction to plain bearings: 1. Plain bearings use high-precision cylindrical rollers (needle rollers) to increase contact length, allowing these bearings to achieve high load capacity and stiffness in a very compact space. 2. DF plain needle roller bearings and plain cylindrical roller bearings feature profiled surfaces on their needle rollers and cylindrical rollers, which reduce edge stress and improve service life.

Where is the windshield washer fluid added in the car?

Windshield washer fluid is typically added to the dedicated washer fluid reservoir in the engine compartment, which has a standardized windshield washer symbol on the cap. The functions of windshield washer fluid include the following points: 1. Anti-freeze function. During winter driving, due to the temperature difference between inside and outside, a lot of frost can accumulate on the windshield, impairing the driver's visibility. Spraying windshield washer fluid can solve this problem because it contains alcohol and other substances that have anti-freeze properties, helping to melt the frost. However, there are different types of windshield washer fluid. If you need anti-freeze functionality, please purchase a proper anti-freeze windshield washer fluid; otherwise, it may not be effective. 2. Anti-fog function. Windshield washer fluid can form a protective film on the glass, preventing fog from forming on the windshield, thus avoiding impaired driver visibility and potential traffic accidents. 3. Lubrication and anti-static function. Windshield washer fluid has a certain lubricating effect, reducing friction between the wiper blades and the glass, thereby extending the lifespan of the wipers and preventing scratches on the glass.

Trending Ranking

What Are the Reasons for the Brake Light Staying On?

How to Diagnose Abnormal Engine Noises?

What are the solutions for abnormal tire wear?

What brand of car is Buick?

Is Toyota Camry the Same as Camry?

How to Use the Automatic Transmission of Audi A6?

How to Use the Car's Internal Air Recirculation?

What are the symptoms of a faulty thermostat in the Excelle?

What are the differences between the Lexus NX and RX?

What are the items included in a car's first maintenance?

More Forum Discussions

How to Shift Gears in the Lynk & Co 02?

What Components Make Up an Engine Lubrication System?

Where is the key slot located on the Toyota Crown?

What Causes Abnormal Noise in Car Shock Absorbers?

Help

Cookie

Cookie Settings

© 2025 Servanan International Pte. Ltd.