What to Do When the Three Temporary License Plates Are Used Up?

1 Answers
MacLucille
07/24/25 5:39pm
Once the three temporary license plates are used up, you cannot apply for temporary license plates anymore. The duration of a temporary license plate is generally 15 days (sometimes 30 days), and after using up the three temporary license plates, no more temporary license plates can be issued. During the period when the temporary license plate has expired but the official license plate has not yet been obtained, driving on the road is not allowed. Temporary license plates include: temporary license plates for administrative jurisdictions, temporary license plates for cross-administrative jurisdictions, temporary license plates for testing, and temporary license plates for special-type motor vehicles. A temporary license plate is a paper motor vehicle license plate that allows temporary road use, also known as a temporary driving license plate. It is a temporary vehicle driving certificate issued by the vehicle management department of the public security bureau for newly purchased vehicles before they are officially registered.
Was this review help?
9
1
Share
More Forum Discussions

Does the Toyota Corolla Have a Timing Belt?

Toyota Corolla does not have a timing belt; it uses a timing chain instead. Here is some information about the Toyota Corolla's timing chain: 1. Under normal circumstances, the timing chain is maintenance-free for life, whereas rubber timing belts, along with other components such as tensioners, idler pulleys, and water pumps, wear out or degrade over time with engine operation. 2. The timing chain serves the same purpose as the timing belt. The timing chain is a product of advancements in automotive technology and industrial development, essentially an "evolution" of the timing belt.
10
5
Share

How to Turn on the Fog Lights of a Buick Excelle?

Buick Excelle is only equipped with one left rear fog light. The method to turn on the rear fog light is as follows: 1. Rotate the light switch to position "3" to turn on the car's headlights. The rear fog light can only be turned on when the headlights are on. 2. Then press the "6" button to turn the rear fog light on or off. When the fog light is on, the indicator light on the instrument panel will illuminate. 3. The rear fog light can be turned off independently of any other lights. Here is some information about the fog lights of the Buick Excelle: 1. The Excelle is not equipped with front fog lights, and there is only one rear fog light, located on the left side. 2. Two rear fog lights can easily be confused with brake lights.
13
5
Share

How many liters of engine oil does the Mercedes-Benz E300 require?

The Mercedes-Benz E300 requires 7 liters of engine oil. The new Mercedes-Benz E300 uses engine oil with the specification 5W40. If you want to change the oil during later maintenance, you can choose from brands like Shell, Castrol, Great Wall, Tongyi, or Tianshan. The viscosity of engine oil changes with temperature, so special attention must be paid to its performance under both low and high temperatures. For example, in 5W-30, the first number indicates low-temperature fluidity. 5W means it can withstand temperatures as low as -30°C. The smaller this number, the better the low-temperature fluidity, making cold starts smoother. The latter number represents the kinematic viscosity of the oil at 100°C. A higher value means the oil can maintain its viscosity index better at high temperatures, which can also be understood as better lubrication performance under high-temperature conditions. The method for changing the engine oil in a Mercedes-Benz E300 is as follows: Wait for the engine temperature to cool down, allowing the oil to flow back into the oil pan. Use a wrench to loosen the oil drain plug and place an oil pan underneath to catch the old oil until it stops dripping. Start the engine and let it run for about 30 seconds to allow the oil in the main oil passages to drain out. Use a specialized wrench to remove the oil filter. Apply some oil to the seal of the new oil filter and tighten it clockwise by hand. Add the new oil through the oil filler cap on the engine valve cover. Generally, fill about three-quarters of a standard oil container. Start the engine and let it run for 5 minutes, then check for any leaks around the oil drain plug and oil filter. If leaks are found, perform necessary repairs. After stopping the engine, pull out the oil dipstick to check if the oil level is within the standard range.
20
4
Share

How to reset the engine oil for a 2017 Cruze?

Here are the steps to reset the engine oil for a 2017 Cruze: 1. Start the Cruze and press the "SET" button on the left side of the steering wheel; 2. Press the "OK" button on the right side of the steering wheel; 3. Observe the dashboard of the Cruze, and you will notice that the engine oil has been successfully reset. Below is some information about the Cruze: 1. The Chevrolet Cruze is a next-generation model developed by General Motors with the goal of creating a benchmark in design and performance for compact cars, integrating global resources. 2. The Cruze attracts attention with its avant-garde design style, and its precise manufacturing craftsmanship makes it a potential new benchmark for compact cars.
7
3
Share

Does the Volkswagen Jetta have an anti-collision beam?

Volkswagen Jetta only has a front anti-collision steel beam, but no rear anti-collision beam. Here is more information about the anti-collision beam: 1. The anti-collision beam is the first device to bear the impact force in a vehicle, playing a crucial role in the passive safety of the vehicle by distributing the force throughout the body to protect the vehicle; 2. The function of the anti-collision steel beam is to reduce the impact energy absorbed by the vehicle during a collision. It consists of a main beam, an energy absorption box, and a mounting plate connected to the vehicle. Both the main beam and the energy absorption box can effectively absorb collision energy during low-speed collisions, minimizing the damage to the vehicle's longitudinal beams and thus protecting the vehicle.
20
0
Share

What is the method for repairing rice grain-sized pits on the windshield?

The method for repairing rice grain-sized pits on the windshield is: 1. After drilling, clean out the glass debris inside the pit, otherwise it will affect the repair effect; 2. Use a repair tool to inject the repair fluid into the pit and apply pressure, allowing the repair fluid to gradually fill the pit; 3. Use a UV lamp to cure the repair fluid; 4. Remove the repair tool and scrape off any residual repair fluid on the surface with a blade to complete the repair. The principle of repairing rice grain-sized pits on the windshield is to fill the pit or crack with a repair fluid that has a refractive index similar to that of glass, which can cover the crack and prevent further cracking, thereby achieving the repair effect. Since the car's front windshield is made of double-layered glass, it is necessary to use a glass drill to penetrate the first layer of glass beforehand for better repair results. When drilling, control the force carefully to avoid enlarging the damaged area.
1
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.