What to Do When the Rear Bumper Has Paint Cracks from Impact?

What does it mean when the airbag fault light comes on in the car?

The display of an airbag fault is usually caused by loose wiring or poor plug contact. It could also indicate a malfunction in the airbag itself, the airbag sensor, or the airbag computer board. Any of these three scenarios may trigger the airbag fault warning. Below is additional information: 1. If the airbag warning light continues to flash or stays illuminated for more than 6-8 seconds after starting the vehicle, or if it flashes for 5 seconds and then stays lit while driving, these are signs that the airbag system may be faulty. In such cases, it is advisable to visit a 4S shop for inspection as soon as possible. 2. An airbag system typically consists of sensors, a microprocessor, an electronic control unit, an airbag cover and support ring, the airbag itself, and the airbag module. When performing maintenance or diagnostics on the airbag system, it is crucial to follow the correct sequence of operations strictly. Failure to do so may result in accidental deployment of the airbag during the process, leading to serious accidents, or may cause the airbag system to malfunction.

8

2

Share

What are the reasons for the damage to new energy vehicle chargers?

Reasons for damage to new energy vehicle chargers: 1. Automatic charging after power restoration. 2. Pressing the charging connection device switch stops charging. 3. Excessive temperature of the power battery. 4. Malfunction of the vehicle or charging pile. Additional information: Precautions for charging new energy vehicles: 1. When storing the vehicle unused for a long time, first charge it to 100%, then discharge it to between 25% and 40%. 2. If the storage time exceeds three months, the battery must be charged; otherwise, battery performance will degrade.

12

0

Share

Does Crossing the Stop Line with Front Wheels Count as Running a Red Light?

Crossing the stop line with front wheels does not count as running a red light. Running a red light refers to the act of a motor vehicle violating traffic signal instructions by crossing the stop line and continuing to move when the red light is on, which prohibits passage. At least three pieces of photographic evidence are required to confirm a red light violation: the vehicle has not left the stop line when the red light is on; the vehicle has passed through the intersection when the red light is on; the vehicle has crossed the line and continued to move forward when the red light is on. Although crossing the line with front wheels does not count as running a red light, stopping after crossing the line is considered over-line parking. Article 26 of the Road Traffic Safety Law states: Traffic signals consist of red, green, and yellow lights. A red light indicates prohibition of passage, a green light indicates permission to pass, and a yellow light serves as a warning. Article 44 states: Motor vehicles passing through intersections shall do so in accordance with traffic signals, traffic signs, traffic markings, or the direction of traffic police. Item 2 of the first paragraph of Article 2 of the Scoring Standards for Road Traffic Safety Violations stipulates that driving a motor vehicle in violation of traffic signal instructions results in a deduction of 6 points. Ways to avoid running a red light: When there are arrow signal lights, follow the arrow lights; otherwise, follow the round lights; When the red light is on, the front of the vehicle must not cross the stop line; When the yellow light is on, the front of the vehicle must not cross the stop line; When the green light just flashes, if the distance is close and the speed is fast, you should pass through, as braking might not stop the vehicle in time to avoid crossing the stop line; if the distance is far, the speed is slow, or the intersection is congested, you should stop; When driving in the city, develop the habit of looking for traffic lights whenever you see a crosswalk or stop line and approach an intersection.

20

5

Share

What Causes a Car to Have No Idle Speed?

Reasons for a car having no idle speed: 1. Low car battery voltage; Specific detection method: Use a multimeter voltage range to test the battery voltage. If it's below 10V, replacement is recommended. If it's around 11V, it can barely be used; be prepared for replacement. Above 12V is usable. 2. Check if it's caused by carbon deposits; if the car has run about 20,000 KM, focus on inspecting and cleaning the throttle body. 3. Inspect, test, and replace the spark plugs. 4. The control unit receives incorrect signals and issues wrong commands, leading to inaccurate control of the engine idle air intake, causing abnormal engine combustion. 5. Faulty idle air actuator resulting in inaccurate idle air control.

10

3

Share

Why are the lights still on after the car is turned off?

Brake switch malfunction or car circuit failure. Detailed explanations for why the car lights remain on after turning off the power are as follows: 1. Brake switch malfunction: If the tail lights remain on after the car is turned off, it may be due to a faulty brake switch. If the brake switch is confirmed to be the issue, the owner can replace the brake light switch themselves. If unable to resolve it personally, it is advisable to visit a professional repair shop for more reliable service. 2. Car circuit failure: If the issue is not the brake light switch, it may be due to a circuit failure in the car. Since car circuits are complex, it is not recommended to handle this issue yourself. Instead, take the car to a 4S shop or a professional repair shop for proper handling.

15

5

Share

What does it mean when the Haval H6 displays a brake system malfunction?

The reasons for brake system malfunctions are: 1. Severe brake pad wear: Brake pads come in two types, with or without sensor lines. Those with sensor lines will automatically complete the circuit when worn to their limit, triggering the warning light. If the issue is worn brake pads, theoretically the vehicle can still be driven for a few hundred kilometers, but it's not recommended as it leads to longer braking distances, softer brakes, increased noise, and potential damage to the brake discs. It's advisable to regularly replace brake pads based on driving habits and road conditions. 2. Low brake fluid level: Brake fluid plays a crucial role in the vehicle's braking system. When the brake pedal is pressed, the force is transmitted by the master cylinder's piston through the brake fluid to the wheel's brake calipers, causing the brake pads to contact the wheels and stop the vehicle. Low brake fluid may also result in noticeably reduced braking power or even complete brake failure. This can be resolved by promptly replenishing the brake fluid. 3. Other issues: Besides the common faults mentioned, other possible causes for the brake system warning light include brake system oil leaks or false alarms. If the brake system warning light comes on while driving, remain calm, gradually slow down, pull over safely, and then diagnose the issue.

19

3

Share

What to Do When the Rear Bumper Has Paint Cracks from Impact?

What does it mean when the airbag fault light comes on in the car?

What are the reasons for the damage to new energy vehicle chargers?

Does Crossing the Stop Line with Front Wheels Count as Running a Red Light?

What Causes a Car to Have No Idle Speed?

Why are the lights still on after the car is turned off?

What does it mean when the Haval H6 displays a brake system malfunction?

Can Elderly Mobility Scooters Be Driven on Public Roads?

Will Small Scratches on the Car Body That Expose the Primer Rust?

Where to Add Coolant in a Volvo?

Why Does a Car Make Strange Noises After Passing Through a Puddle?