What to Do When the One-Key Start Key of Emgrand Runs Out of Battery?

How to Activate ETC for the Second Time?

ETC second activation method: Insert and remove the ETC card twice consecutively until the electronic tag screen displays "Bluetooth is on". If it shows "Tag invalid" when inserting and removing twice without the electronic tag attached, this is normal and does not affect activation. Alternatively, you can directly press the button on top of the electronic tag to enable Bluetooth function. Turn on your phone's Bluetooth, open the corresponding mobile APP (usually there is a download QR code on the electronic tag), and enter the device activation interface. Click on device connection and wait patiently for the "Connection successful" prompt. After successful connection, upload a photo of the vehicle's front to complete activation. ETC installation positions: For small vehicles like cars and minivans, the ETC card and OBU device should be installed on the upper middle part of the front windshield. For large vehicles like trucks and buses, the installation position is on the lower middle part.

8

0

Share

Which Year Does China IV Vehicles Belong To?

China IV vehicles were produced after 2011, with some also manufactured in 2010. Here is more relevant information: 1. China IV Emission Standard: The China IV emission standard is the national fourth-phase motor vehicle pollutant emission standard. Compared to China III, it requires light-duty vehicles to reduce single-vehicle pollutant emissions by approximately 50%, heavy-duty vehicles to reduce single-vehicle emissions by about 30%, and particulate matter emissions by over 80%. 2. About Passenger Vehicle Emission Test Cycles: Different countries and regions adopt different emission standards based on their actual conditions. For example, the United States has the U.S. standard, Europe has the Euro standard (Euro IV, Euro V, etc.), and China has the China standard (China V, China VI, etc.). However, there are mainly three test cycles for passenger vehicle emissions: the EU's NEDC cycle, the U.S.'s FTP75 cycle, and Japan's JC08 cycle. The China standard is primarily formulated with reference to the Euro standard, while Japan's standard is more influenced by the U.S. standard.

13

2

Share

What are the reasons for the engine warning light in Citroen C-Quatre?

The engine warning light in Citroen C-Quatre may illuminate due to the following 7 main reasons: Sensor malfunction: This includes sensors such as coolant temperature, crankshaft position, air flow, intake temperature, and oxygen sensors. When these sensors are damaged, have poor contact, or signal interruption occurs, the vehicle's ECU cannot accurately obtain engine data, triggering the engine warning light. Fuel/oil quality issues: Failure to use fuel and engine oil as specified by the manufacturer may cause engine wear, leading to the warning light activation. Poor combustion of air-fuel mixture: This can cause engine carbon buildup or knocking. When detected by oxygen sensors and reported to the ECU, the warning light will illuminate as an alert. Causes include spark plug failure, ignition coil failure, fuel pump failure, or fuel line blockage. Turbocharging issues: Problems with intake boost pipes or turbochargers can trigger the engine light. The most common is turbocharger damage, often accompanied by oil leaks, high oil consumption, reduced power, metallic noises, or blue/black exhaust smoke. Intake problems: Engine pipe blockages caused by intake issues may trigger the warning light, especially when air filters are dirty or not regularly cleaned. Exhaust system issues: Exhaust faults like rear oxygen sensor failure, catalytic converter problems, or exhaust camshaft/bearing failures can activate the warning light. Leaded gasoline, improper lubricant additives, physical damage to the catalytic converter, or fuel system failures often cause catalytic converter issues. Anti-theft system malfunction: If the electronic anti-theft system fails or doesn't match the engine ECU, it may prevent normal engine operation while illuminating the warning light. When the engine warning light illuminates, follow these steps: 1. First check if the engine operates normally. If there's shaking, black smoke, etc. (especially with red warning lights), do not restart the engine. 2. If the engine can start, turn off for 5-10 minutes, then power on without braking (press start button or turn key halfway to ON position). After 5-10 seconds of self-check, observe if the warning light turns off. 3. If the light persists, visit a service center immediately. Technicians can read diagnostic trouble codes using portable scanners for targeted repairs.

10

2

Share

What is a Reverse Curve?

Reverse curve refers to two adjacent curves with opposite directions. Below is a detailed introduction about reverse curves in driving: Overview: The reverse curve traffic warning sign is appropriately placed before two adjacent curves with opposite directions. This warning sign alerts drivers to slow down, with a safe driving speed not exceeding 60km/h. Reverse curve traffic warning signs are mostly found in mountainous areas. Others: Road signs can generally be categorized into six types: warning signs, prohibition signs, directional signs, guide signs, tourist area signs, and road construction safety signs.

7

2

Share

Does Porsche have a 418 model?

No, here is more information about Porsche: 1. Overview: Porsche, also translated as Porsh, is a world-renowned luxury car brand under the German Volkswagen Group, headquartered in Stuttgart, Germany, and is one of the main representatives of European and American automobiles. Main models include the 911, 718, Boxster, Cayman, Panamera, Cayenne, and Macan. 2. Other Information: Founded in 1931 in Stuttgart, Porsche is renowned worldwide for producing high-end sports cars. The founder, Ferdinand Porsche, was a globally celebrated automotive designer.

19

2

Share

Can Water Enter the Transmission When Driving Through Water?

After driving through water, the transmission, differential, or front/rear axles and differential may take in water. Generally, transmission water ingress is mainly caused by the following two situations: Water level exceeds two-thirds of the wheel: If the water level surpasses two-thirds of the wheel, the probability of water entering the transmission is around 80% to 90%. If the water has reached the dashboard level, the transmission is 100% flooded. Water splash during oncoming traffic: When encountering oncoming vehicles, excessive road water can lead to water entering the transmission. Once water enters the transmission, the performance of the transmission fluid will be affected. The performance of the transmission fluid will also degrade, causing the clutch plates to slip.

14

5

Share

What to Do When the One-Key Start Key of Emgrand Runs Out of Battery?

How to Activate ETC for the Second Time?

Which Year Does China IV Vehicles Belong To?

What are the reasons for the engine warning light in Citroen C-Quatre?

What is a Reverse Curve?

Does Porsche have a 418 model?

Can Water Enter the Transmission When Driving Through Water?

Solutions for High Water Temperature in Diesel Engines

What does the white triangle exclamation mark on the Audi A6 dashboard mean?

How Long Does It Take to Perform a Car Maintenance?

How to Determine if a Car Needs to Refill Antifreeze?