What to Do When the Gear Shift Lever Light of BMW 5 Series Doesn't Work?

Is it necessary to replace the oil drain plug during car maintenance?

It is not always necessary to replace the oil drain plug during car maintenance. The specific circumstances are as follows: 1. Depending on the vehicle model: Some vehicle models require the oil drain plug to be replaced every time the oil is changed. 2. Reason for replacement: The main purpose of replacing the oil drain plug with a new one during each oil change is to prevent oil leakage. Relevant information about the oil drain plug is as follows: 1. Oil pan drain plug: This is a screw located at the bottom of the engine oil pan. 2. Function: When the engine requires an oil change during maintenance, this screw is loosened to drain the old oil from the engine. After tightening the screw, new oil is added through the engine's filling port.

4

2

Share

Is Antifreeze the Same as Coolant?

Coolant and antifreeze are the same, with no difference. The full name of antifreeze is antifreeze coolant, which serves two purposes: 1. When the vehicle is not running, it prevents freezing. Since the antifreeze is in the engine block, liquid turning into solid will expand in volume, which could crack the engine block. 2. After the vehicle starts, it cools the engine to prevent overheating, which could damage the engine. Not replacing the antifreeze for a long time will cause its quality to deteriorate, reducing its anti-rust properties and damaging components like the radiator and pipes. It will also affect the boiling and freezing points, impacting the antifreeze or cooling performance and potentially harming the engine.

7

4

Share

What car is the Buick SGM7240ATA?

Buick SGM7240ATA is a sedan under the Buick brand. Here are the specific details about the Buick SGM7240ATA: 1. Body dimensions: The car has a length of 4998mm, width of 1851mm, height of 1461mm, a wheelbase of 2807mm, and front/rear track widths of 1576mm and 1568mm respectively. 2. Powertrain configuration: The car is equipped with a 2.4L naturally aspirated engine, delivering a maximum horsepower of 170PS and a maximum torque of 225NM at 4480rpm, paired with a 6-speed automatic manual transmission.

16

4

Share

Why does the fuel dispenser run idle without dispensing fuel?

Here are the reasons why a fuel dispenser may not dispense fuel: 1. Failure of the oil-gas separator: When the oil valve of the oil-gas separator in the fuel truck gets stuck, it can cause the fuel dispenser to fail in dispensing fuel. 2. Failure of the vane pump: The overflow valve of the vane pump cannot close; the vane springs inside the pump, which rotate at high speed with the rotor for a long time, may wear out or break due to fatigue, leading to increased internal leakage of the vanes. In severe cases, this can cause the fuel dispenser to fail in dispensing fuel. 3. The solenoid valve of the fuel dispenser cannot open: If the wiring of the solenoid valve is disconnected or the relay or lamp valve board is damaged, the solenoid valve may fail to open, subsequently causing the fuel dispenser to not dispense fuel.

18

2

Share

What Causes the Car Fan to Stop Rotating and the Water Temperature to Rise?

Car fan not rotating and high water temperature are caused by a short circuit in the motor. The following are the specific reasons for high car water temperature: 1. Insufficient coolant: Coolant leakage or insufficient coolant can cause the engine water temperature to rise. In this case, the coolant level should be checked and topped up to the appropriate level if necessary. Check again after a few days to see if the level has dropped significantly. If it has, locate the source of the leak. 2. Faulty cooling fan: When the vehicle is running at high speeds, the heat generated cannot be transferred to the coolant in time, affecting heat dissipation and causing the coolant temperature to rise. This can also lead to issues like boiling over.

14

1

Share

What are the effects of scraping the car's chassis?

The impact of scraping the car's chassis is: it damages the protective paint on the chassis. Damage to the protective paint can easily lead to rust and deterioration of the chassis. If the car's chassis is severely scraped, it may affect various components underneath, resulting in the car being unable to drive. Below is some related information about the chassis: 1. About the chassis: The chassis refers to the combination of the transmission system, running system, steering system, and braking system on a car. It supports and installs the car's engine and its various components and assemblies, forming the overall shape of the car, bearing the engine's power, and ensuring normal driving. 2. The functions of the car chassis are as follows: (1) Corrosion prevention; (2) Stone impact prevention; (3) Vibration prevention; (4) Heat insulation; (5) Noise reduction; (6) Bottoming prevention.

4

5

Share

What to Do When the Gear Shift Lever Light of BMW 5 Series Doesn't Work?

Is it necessary to replace the oil drain plug during car maintenance?

Is Antifreeze the Same as Coolant?

What car is the Buick SGM7240ATA?

Why does the fuel dispenser run idle without dispensing fuel?

What Causes the Car Fan to Stop Rotating and the Water Temperature to Rise?

What are the effects of scraping the car's chassis?

Can Accident Vehicles Be Insured?

Is pressing the right corner during a right-angle turn due to turning the wheel too early or too late?

What are the symptoms of an air leak in a car engine?

What brand of spark plugs does the Roewe 350 come with from the factory?