What to Do When the Clutch Disc and Pressure Plate Stick Together?

1 Answers
MatteoMarie
07/30/25 7:07am
If the clutch disc and pressure plate are stuck together, it indicates an issue with the transmission's separation, most likely because the clutch is frequently in a semi-engaged state. If they are burnt out, replace them and then adjust the clutch's engagement point. Replacement may not be necessary; during installation, lightly sand the clutch disc with coarse sandpaper.
Was this review help?
2
1
Share
More Forum Discussions

How to Replace the Air Conditioning Filter in a Lexus RX?

Method for replacing the air conditioning filter in a Lexus RX: 1. Open the engine hood; the air conditioning filter is located near the passenger side, covered by a plastic panel. 2. Unscrew the bolts on this plastic panel, then peel off a section of the front rubber strip to remove the panel and reveal the air conditioning filter. 3. There are clips on both sides of the air conditioning filter; pull these clips outward to remove the filter. In terms of powertrain, the Lexus RX is equipped with a 2.7 to 3.5-liter inline four-cylinder double overhead camshaft (DOHC) engine. Thanks to the inclusion of a Dual Variable Valve Timing with intelligence (VVT-i) system, the Lexus RX achieves higher fuel efficiency and lower emissions.
7
5
Share

Is a Push-to-Start Car Easy to Steal?

A push-to-start car is not easy to steal, primarily because it comes with anti-theft features. The functions of push-to-start include: 1. Starting and turning off the engine; 2. Fully intelligent sensing start; 3. Intelligent sensing entry; 4. Intelligent sensing door closing; 5. Smart identity recognition between the driver and the car; 6. Anti-theft design that cuts off fuel and power. The steps to start a push-to-start car are: 1. When the driver sits in the cockpit, press the start button for the car to perform a self-check; 2. Press the brake and push the start button to ignite the engine; 3. Press the foot brake, shift to D gear, and release the handbrake to start moving. The steps to park a push-to-start car are: 1. After reaching the destination, press the brake and shift to N gear, and the electronic handbrake will automatically engage; 2. Once the electronic handbrake light is on, release the brake.
19
5
Share

How Can Deaf and Mute People Obtain a Driver's License?

Deaf and mute individuals can obtain a driver's license. However, according to the 'Regulations on the Application and Use of Motor Vehicle Driving Licenses,' they must wear hearing aids. They must be able to distinguish the direction of sound sources with each ear at a distance of 50 centimeters from a tuning fork. Those with hearing impairments who can meet the above conditions by wearing hearing aids can apply for a motor vehicle driving license for small cars and small automatic transmission vehicles. Applicants for a motor vehicle driving license should submit their applications to the vehicle management office according to the following regulations: 1. If residing in their registered permanent residence, they should apply there; 2. If residing outside their registered permanent residence, they can apply at their current place of residence; 3. Active military personnel (including armed police) should apply at their place of residence; 4. Foreign nationals should apply at their place of residence or stay; 5. Those applying to add permitted vehicle types should apply at the place where their current motor vehicle driving license was issued; 6. Those undergoing full-time driving vocational education and applying to add large passenger vehicles or tractor permitted vehicle types should apply at the place where they are receiving education.
10
0
Share

How to Adjust the Height of the Seat Headrest?

Introduction to Adjusting Seat Headrest Height: When adjusting the height of the headrest, ensure that the center of the headrest aligns with the center of the back of your head to provide effective protection. The primary function of the seat headrest is to protect the cervical spine of the driver and passengers in the event of a rear-end collision. Below are the detailed steps: 1. Adjust the Seat Back Angle: Before adjusting the headrest, first adjust the angle of the seat back. The seat back should be as upright as possible, allowing the neck to maintain a gentle angle. A flatter angle between the neck and the body helps reduce the risk of injury in sudden situations. To ensure the headrest fully supports the head during an emergency, the center of the back of your head should align with the center of the headrest. 2. Minimize the Distance Between the Head and the Headrest: The smaller the distance between the back of your head and the headrest, the better the cushioning effect in case of sudden impact. Typically, the distance should be less than 4 centimeters. After adjusting the seat and headrest, check if the locking mechanism is secure by gently shaking and pushing it.
3
2
Share

How to reset the tire pressure light on a BMW X1?

The method to reset the tire pressure light on a BMW X1 is as follows: On the BMW X1 control panel, select vehicle information, then choose vehicle status, and select confirm tire pressure. Start the engine but do not begin driving. Initiate the tire pressure reset process, and then start driving to complete the reset. There are many reasons why the tire pressure light may illuminate, with several main possible causes: 1. Abnormal tire pressure itself. This is an essential function of the tire pressure monitoring system to alert customers when tire pressure is abnormal, ensuring their safety. Abnormal tire pressure includes pressure that is too high or too low. Generally, automakers require a low-pressure alert below 160kpa and a high-pressure alert above 280kpa. 2. Abnormal tire pressure system. This refers to issues with the vehicle itself, where the tire pressure is normal but the system indicates a problem. Possible causes include abnormalities in the tire pressure module or the signal-sending sensors, also known as component malfunctions. It is recommended to visit an official 4S dealership for timely inspection and repair.
3
3
Share

Where is the memory card slot for the Binyue dash cam?

The memory card slot for the Binyue dash cam is located under the front passenger seat, where there is a raised area—that's the card slot. The Binyue is a compact SUV under the Geely brand. By July 2019, just over eight months after its launch, it had achieved sales exceeding 100,000 units, marking a remarkable success. Here’s an introduction to this model: 1. Exterior: The front features an aggressive, forward-leaning design, giving it a sporty, low-slung stance. The hood has two symmetrical raised lines with sharp edges. The side profile adopts a wind-wing-inspired fastback design, paired with dual five-spoke wheels for a dynamic look. 2. Interior: The cabin offers a wide field of vision with an integrated eco-friendly design. The 7-inch LCD instrument cluster comes in three different colors, exuding a high-tech feel. The star-ring textured center console area enhances the premium touch. The steering wheel, door armrests, and seats are wrapped in leather for added comfort. 3. Features: In terms of safety, the Binyue is equipped with an ACC intelligent adaptive cruise system, LKA lane-keeping assist system, ICC intelligent navigation system, and other features to improve driving comfort and safety.
18
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.